91.100.40 纤维增强水泥制品 标准查询与下载
共找到 362 条与 纤维增强水泥制品 相关的标准，共 25 页
The document establishes an agreed method for evaluation of pull through resistance (tension/compression for fasteners through the sheets), shear resistance, bending strength and bending modulus of elasticity and suggests an approved safety concept of fibre-cement flat sheets for internal and external wall and ceiling finishes based on the experiences obtained over the last number of years in different countries. The results are only applicable to the fibre-cement product and not to the complete fixing assembly. NOTE 1 For design purposes of fibre-cement flat sheets in the final application, the failure modes pull-out and breaking of the fixing or substructure are not in the scope of this standard. They might become decisive and need to be tested or calculated according to the relevant design standards for fixings (e.g. EN 14592) or ETA and substructure (e.g. Eurocode 3 for steel, Eurocode 5 for wood and Eurocode 9 for aluminium substructures) and compared with the results for pull-through and shear resistance. The results are also applicable for: — Coated or uncoated sheets manufactured at the same production facility as the tested sheets provided that the sheets are of the same type, have at least the same declared class according to EN 12467:2012+A2:2018, Table 6 and at least the same nominal thickness. — The test method can be applied to textured or non-textured fibre-cement flat sheets. The results of non-textured sheets are only applicable for textured sheets if the nominal minimum thickness of the textured sheet is at least the nominal thickness of the non-textured sheet. — The same type of fixing head or washer assembly where applicable if the diameter of the fixing head or washer is 0 mm to 2 mm larger than in the test. — The Shore A hardness of the sealing washer, where applicable, is ± 5 that of the washer used in the test, given that the washer thickness is at least as thick, the washer material at least as strong and the shape (dome or flat) of the washer equal to what has been tested. NOTE 2 A) For pull-through resistance, if the diameter of the drilled hole through the fibre-cement sheet is 0 mm to 2 mm smaller or equal than in the test up to the diameter of the shank of the fastener, providing, during the test there is the required clearance hole around the shank of the fastener. B) For shear resistance, if the diameter of the drilled hole is equal to what has been tested. It applies only to products as delivered.
Fibre cement products - Determination of pull through and shear resistance and bending strength calculations - Part 1: Flat sheets
- ICS
- 91.100.40
- CCS
- 发布
- 2022-04-27
- 实施
- 2022-07-31
本规程适用于城市轨道交通工程用结构混凝土，包括地下结构含围护结构、高架结构、道床结构与附属地面建筑结构的主体结构用现浇混凝土和预制构件混凝土。
Technical specification for urban rail transit engineering concrete
- ICS
- 91.100.40
- CCS
- Q14
- 发布
- 2022-04-24
- 实施
- 2022-06-01
为推广纤维增强复合材料在混凝土结构加固工程中的应用，规范其设计、施工与验收工作，由安徽工业大学和马鞍山钢铁建设集团有限公司会同有关单位共同编制了团体标准《纤维增强复合材料加固混凝土结构技术规程》（简称规程）。 在规程编制过程中，编制组查阅了大量文献资料，开展相关试验研究、理论分析与数值模拟，总结近年来在纤维增强复合材料加固领域的实践经验，并与相关标准进行参考和协调，在广泛征求意见的基础上，编制本规程。 本规程分为9章14个附录，其主要技术内容有：总则、术语和符号、基本规定、材料、FRP片材加固混凝土构件计算、FRP筋加固混凝土构件计算、裂缝修补技术、施工、验收。
Technical Regulations for Strengthening Concrete Structures with Fiber Reinforced Composite Materials
- ICS
- 91.100.40
- CCS
- C302
- 发布
- 2022-03-29
- 实施
- 2022-05-01
本文件规定了超高性能混凝土外墙板的分类与标记、一般规定、原材料、要求、试验方法、检验规则、标志、运输、贮存与出厂合格证。 本文件适用于非承重超高性能混凝土外墙板。
Ultra-high performance concrete（UHPC) panel for exterior wall
- ICS
- 91.100.40
- CCS
- B109
- 发布
- 2022-03-22
- 实施
- 2023-02-10
本文件规定了超高性能混凝土外墙板的分类与标记、一般规定、原材料、要求、试验方法、检验规则、标志、运输、贮存与出厂合格证。
Ultra-high performance concrete（UHPC) panel for exterior wall
- ICS
- 91.100.40
- CCS
- C302
- 发布
- 2022-03-22
- 实施
- 2022-05-12
本文件规定了超高性能混凝土装饰制品的分类与标记、一般规定、原材料、要求、试验方法、检验规则、标志、堆放、装卸、运输与出厂合格证。
Ultra-high performance concrete (UHPC) decorative products
- ICS
- 91.100.40
- CCS
- C302
- 发布
- 2022-03-22
- 实施
- 2022-05-12
本文件规定了超高性能混凝土装饰制品的分类与标记、一.般规定、原材料、要求、试验方法、检验规则、标志、堆放、装卸、运输与出厂合格证。 本文件适用于非承重超高性能混凝土装饰制品。
Ultra-high performance concrete (UHPC) decorative products
- ICS
- 91.100.40
- CCS
- B109
- 发布
- 2022-03-22
- 实施
- 2022-07-22
本文件规定了短切玄武岩纤维混凝土预制构件的术语和定义、原材料要求、性能要求、配合比设计要求、生产施工要求。
Technical requirements for chopped basalt fiber reinforced concrete precast components
- ICS
- 91.100.40
- CCS
- Q13
- 发布
- 2021-10-20
- 实施
- 2021-11-20
承载力、抗拉伸强度、断裂延伸率、撕裂强度、耐酸、耐碱、抗老化、耐磨
Vulcanized rubber anti falling net
- ICS
- 91.100.40
- CCS
- E489
- 发布
- 2021-10-16
- 实施
- 2021-10-16
产品结构、材料要求、外观、结构尺寸、总间隙（总缝宽）、承载能力、残留变形、专用硫化橡胶原材料性能要求
The groove cover made of vulcanized rubber steel frame composite material is provided with a cone-shaped leak proof bucket and a water grate connected with a flexible buckle
- ICS
- 91.100.40
- CCS
- E489
- 发布
- 2021-10-16
- 实施
- 2021-10-16
Fibre-cement products - Determination of pull through and shear resistance and bending strength calculations - Part 2: Profiled sheets
- ICS
- 91.100.40
- CCS
- 发布
- 2021-10-00
- 实施
1.1?This test method compares the surface cracking of fiber reinforced concrete panels with the surface cracking of control concrete panels subjected to prescribed conditions of restraint and moisture loss that are severe enough to produce cracking before final setting of the co
Standard Test Method for Evaluating Plastic Shrinkage Cracking of Restrained Fiber Reinforced Concrete (Using a Steel Form Insert)
- ICS
- 91.100.40
- CCS
- 发布
- 2021-06-01
- 实施
1.1?This test method determines the quasi-static longitudinal tensile strength and elongation properties of fiber reinforced polymer matrix (FRP) composite bars commonly used as tensile elements in reinforced, prestressed, or post-tensioned concrete. Note 1:?Additional procedure
Standard Test Method for Tensile Properties of Fiber Reinforced Polymer Matrix Composite Bars
- ICS
- 91.100.40
- CCS
- 发布
- 2021-05-15
- 实施
外观、结构尺寸、嵌入深度、井座、承载能力、专用硫化橡胶原材料性能要求、特殊防漏防臭井盖防水等级
Vulcanized rubber steel frame composite manhole cover
- ICS
- 91.100.40
- CCS
- E489
- 发布
- 2021-04-16
- 实施
- 2021-04-17
1.1?This test method describes the apparatus and procedure for evaluating the pull-off strength of wet lay-up or pultruded (shop-fabricated) Fiber Reinforced Polymer (FRP) laminate systems adhesively bonded to a flat concrete substrate. The test determines the greatest perpendic
Standard Test Method for Pull-Off Strength for FRP Laminate Systems Bonded to Concrete or Masonry Substrates
- ICS
- 91.100.40
- CCS
- 发布
- 2021-01-01
- 实施
Method for tension test of steel fibers for concrete
- ICS
- 91.100.40
- CCS
- 发布
- 20201112
- 实施
- 20201112
本标准规定了防火用硅酸钙板的术语和定义、分类、等级、规格和标记、原材料、要求、试验方法、检验规则、标志、包装、运输和贮存。
Calcium silicate boards for fire-resistance
- ICS
- 91.100.40
- CCS
- C302
- 发布
- 2020-03-26
- 实施
- 2022-05-12
本标准规定了工业涂装及贴面用纤维水泥板的术语和定义、分类、等级、规格和标记、原材料、要求、试验方法、检验规则、标志、包装、运输和贮存。
Fiber cement flat sheets for industrial coatings and veneering
- ICS
- 91.100.40
- CCS
- C302
- 发布
- 2020-03-26
- 实施
- 2022-05-12
本标准规定了工业涂装及贴面用纤维水泥板的术语和定义、分类、等级、规格和标记、原材料、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于工业涂装及贴面用纤维水泥板。工业涂装及贴面用硅酸钙板可参照本标准执行。
Fiber cement flat sheets for industrial coatings and veneering
- ICS
- 91.100.40
- CCS
- C302
- 发布
- 2020-03-26
- 实施
- 2020-04-24
本标准规定了防火用硅酸钙板的术语和定义、分类、等级、规格和标记、原材料、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于防火用途的硅酸钙板。
Calcium silicate boards for fire-resistance
- ICS
- 91.100.40
- CCS
- C303
- 发布
- 2020-03-26
- 实施
- 2020-05-14
