91.100.50 粘合料、密封材料 标准查询与下载

ASTM D2171/D2171M-22 用真空毛细管粘度计测定沥青粘度的标准试验方法

1.1 This test method covers procedures for the determination of the apparent viscosity of asphalt binder by vacuum capillary viscometers at 60 °C [140 °F]. It is applicable to materials having viscosities in the range from 0.0036 to over 20 000 Pa·s [0.036 to over 200 000 P]. NOTE 1—This test method is suitable for use at other temperatures, but the precision is based on determinations on asphalt binders at 60 °C [140 °F]. NOTE 2—Modified asphalt binders or asphalt binders that have been conditioned or recovered are typically non-Newtonian under the conditions of this test. The apparent viscosity for non-Newtonian asphalt binders varies with shear rate. When the flow is non-Newtonian in a capillary tube, the shear rate determined using this test method may be invalid. The presence of non-Newtonian behavior for the test conditions of this test can be verified by measuring the viscosity with viscometers having different-sized capillary tubes or with different pressure heads. The defined precision limits in Section 11 may not be applicable to nonNewtonian asphalt binders. Test Method D4957 may be a more applicable method for testing non-Newtonian asphalts. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 Warning—Mercury has been designated by the United States Environmental Protection Agency (EPA) and many state agencies as a hazardous material that can cause central nervous system, kidney, and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercurycontaining products. See the applicable product Material Safety Data Sheet (MSDS) or Safety Data Sheet (SDS) for details and the EPA’s website—http://www.epa.gov/mercury/ faq.htm—for additional information. Users should be aware that selling mercury, mercury-containing products, or both, in your state may be prohibited by state law. 1.4 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Viscosity of Asphalts by Vacuum Capillary Viscometer

ASTM D5602/D5602M-18(2022) 屋顶薄膜试样抗静态刺穿性的标准试验方法

1.1 This test method covers evaluation of the maximum static puncture load that roofing membrane specimens can withstand without allowing the passage of water. 1.2 This laboratory test is conducted at any desired temperature using sheet membrane specimens manufactured in a factory or prepared in a laboratory. 1.3 Roof membrane specimens to which the test method is applicable include bituminous built-up, polymer-modified bitumens, vulcanized rubbers, non-vulcanized polymeric, and thermoplastic materials. 1.3.1 The applicability of this test method to these membrane specimens includes their use in vegetative roof systems. 1.4 This test method is not applicable to aggregate-surfaced membrane specimens, but it is applicable to specimens having factory-applied granules. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Static Puncture Resistance of Roofing Membrane Specimens

ASTM D6380/D6380M-03(2022) 沥青卷材屋面（有机毡）标准规范

1.1 This specification covers asphalt roofing in sheet form, in widths agreed upon between the purchaser and the producer/ supplier, composed of asphalt-saturated organic felt coated on both sides with asphalt. Class M and WS rolls are surfaced on the (exposed) weather side with mineral granules, except for any selvage. Class S rolls are surfaced with powdered talc, mica, or other fine mineral matter to prevent sticking. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Asphalt Roll Roofing (Organic Felt)

ASTM D5636/D5636M-94(2022) 毛毡或薄板屋顶和防水材料低温展开的标准试验方法

1.1 This test method covers the procedure for the physical testing and analysis of surface cracking due to low-temperature unrolling of roofing composed of bituminous impregnated felts and reinforced polymer-modified bituminous sheet materials. These products may employ various surfacing materials on one side. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Low-Temperature Unrolling of Felt or Sheet Roofing and Waterproofing Materials

ASTM D1461-17(2022) 沥青混合物中水分或挥发性馏分的标准试验方法

1.1 This test method covers the determination, by direct measurement, of moisture or volatile fractions of the asphalt in asphalt mixtures. 1.2 The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard. 1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Moisture or Volatile Distillates in Asphalt Mixtures

ASTM D3289-17(2022) 半固体和固体沥青材料密度的标准试验方法（镍坩埚法）

1.1 This test method covers the determination of the density of semi-solid and solid asphalt materials by weighing in air and in water. NOTE 1—An alternate method for determining the density of semi-solid and solid asphalt materials is Test Method D70/D70M. For materials which are too fluid for use of this method, use Test Method D3142/ D3142M. 1.2 The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard. 1.3 Warning— Mercury has been designated by the United States Environmental Protection Agency (EPA) and many state agencies as a hazardous material that can cause central nervous system, kidney, and liver damage. Mercury or its vapor may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury-containing products. See the applicable product Safety Data Sheet (SDS) for details and EPA’s website—www.epa.gov/mercury/ faq.htm—for additional information. Users should be aware that selling mercury, mercury-containing products, or both, in your state may be prohibited by state law. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Density of Semi-Solid and Solid Asphalt Materials (Nickel Crucible Method)

ASTM D5635/D5635M-18(2022) 屋顶薄膜试样动态抗穿刺性的标准试验方法

1.1 This test method covers the evaluation of the dynamic puncture energy that roofing membrane specimens can withstand, without allowing the passage of water, when subjected to impact from a rigid object having a sharp edge. 1.2 This laboratory test can be conducted at any desired temperature using membrane specimens manufactured in a factory or prepared in a laboratory. 1.3 Roof membrane specimens to which the test method is applicable include bituminous built-up, polymer-modified bitumens, vulcanized rubbers, non-vulcanized polymeric, and thermoplastic materials. 1.3.1 The applicability of this test method to these membrane specimens includes their use in vegetative roof systems. 1.4 This test method is not applicable to aggregate-surfaced membrane specimens; however, it is applicable to specimens having factory-applied granules. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Dynamic Puncture Resistance of Roofing Membrane Specimens

ASTM D3617/D3617M-17(2022) 应用过程中组合屋顶系统的取样和分析

1.1 This practice is a guide for removing specimens for built-up bituminous roof systems during application, but before the application of flood coating and top surfacing, for determining the approximate quantities of the components and the possible presence of moisture, or dry spots between plies, in the field. Components may consist of: 1.1.1 Insulation, when part of the roof membrane system, 1.1.2 Plies of roofing felt, 1.1.3 Interply layers of bituminous material, and 1.1.4 Top coating, if present, before any surfacing aggregate has been applied. 1.2 This practice is applicable to both 914 mm [36 in.] and 1000 mm [393⁄8 in.] wide felt rolls. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Sampling and Analysis of Built-Up Roof Systems During Application

T/CXY 0010-2022 强力瓷砖胶

本文件规定了陶瓷砖胶粘剂的术语和定义、一般要求、要求、试验方法、检验规则及标志、包装、运输和贮存。 本文件适用于陶瓷砖胶粘剂。

Strong Tile Adhesive

T/CBMF 204-2022 地坪行业绿色工厂评价要求

本文件规定了地坪行业绿色工厂评价的总则、评价要求、评价方法及程序、判定和评价报告。 本文件适用于地坪企业的绿色工厂创建与评价。

Requirements for assessment of green factory in floor coatings industry

ASTM E1612/E1612M-94(2022) 建筑物和停车场结构的预制建筑压缩密封标准规范

1.1 This specification covers the physical requirements for the fully cured elastomeric alloy and the movement capabilities of preformed architectural compression seals used for sealing expansion joints in buildings and parking structures. The preformed architectural compression seal is a rectangular elastomeric extrusion, having an internal baffle system produced continuously and longitudinally throughout the material. The architectural compression seal functions under compression and is usually chemically bonded in place with an adhesive. NOTE 1—Movement capability is defined in Test Method E1399/ E1399M. 1.2 This specification covers all colors of architectural compression seals. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Preformed Architectural Compression Seals for Buildings and Parking Structures

ASTM D3909/D3909M-22 矿物颗粒表面的沥青卷材屋顶（玻璃毡）

1.1 This specification covers asphalt-impregnated and coated glass felt roll roofing surfaced on the weather side with mineral granules, for use as a cap sheet in the construction of built-up roofs. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Asphalt Roll Roofing (Glass Felt) Surfaced with Mineral Granules

ASTM D6495/D6495M-18(2022) 土工合成粘土衬里验收试验要求的标准指南

1.1 This guide covers guidelines for the acceptance testing requirements for geosynthetic clay liner (GCL) materials, describing types of tests, test methods, and recommended verifications. 1.2 This guide is intended to aid purchasers, installers, contractors, owners, operators, designers, and agencies in establishing a minimum level of effort for product acceptance testing and verification. This is intended to ensure that the supplied GCL rolls meet accepted material specifications. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.4 This guide offers an organized collection of information or a series of options and does not recommend a specific course of action. This guide cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this guide may be applicable in all circumstances. This guide is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this guide be applied without consideration of a project’s many unique aspects. The word “Standard” in the title of this guide means only that the guide has been approved through the ASTM consensus process. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Acceptance Testing Requirements for Geosynthetic Clay Liners

JC/T 942-2022 丁基橡胶防水密封胶粘带

本文件规定了丁基橡胶防水密封胶粘带（以下简称“丁基胶粘带”）的分类、一般要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于建筑防水工程中接缝密封用丁基胶粘带。 本文件规定的丁基胶粘带适用于高分子防水卷材、水泥混凝土及砂浆、金属板等基材。

Butyl Rubber Waterproof Sealing Adhesive Tape

JC/T 482-2022 聚氨酯建筑密封胶

本文件规定了聚氨酯建筑密封胶的分类、一般要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于以氨基甲酸酯聚合物为主要成分的单组分和多组分聚氨酯建筑密封胶。

Polyurethane building sealant

JC/T 483-2022 聚硫建筑密封胶

本文件规定了聚硫建筑密封胶的分类、一般要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于以液态聚硫橡胶为基料的室温硫化多组分建筑密封胶。 本文件不适用于中空玻璃二道密封用聚硫密封胶。

polysulfide building sealant

KS F 2368-2022 沥青和波特兰水泥混凝土路面接缝和裂缝热涂密封剂和填料的测试方法

Testing method for sealant and filler, hot-applied, for joints and cracks in asphaltic and portland cement concrete pavements

BS ISO 11617:2022 建筑和土木工程密封剂 测定静态固化样品暴露于人工风化和机械循环后弹性防风雨密封胶的内聚力和外观变化

1   Scope This document specifies laboratory exposure procedures for determining the effects of cyclic movement and artificial weathering on cured, elastic weatherproofing joint sealants (one- or multi-component).

Building and civil engineering sealants. Determination of changes in cohesion and appearance of elastic weatherproofing sealants after exposure of statically cured specimens to artificial weathering and mechanical cycling

T/CABEE 039-2022 建筑外围护结构缝隙用气密性膜系统 技术规程

本技术规程适用于民用建筑工程中外围护结构缝隙处的气密性膜系统设计、施工和验收。《规程》明确了膜系统的定义，重点研究了膜系统关键性能，提出了技术指标，完善了膜系统的设计要求、施工工艺和验收方法。

Technical specification for air-tight membrane system for gaps in building envelope

ASTM D8052/D8052M-22 低斜面屋顶组件空气泄漏定量的标准测试方法

1.1 This test method provides a laboratory technique for determining air leakage in low-sloped membrane roof assemblies under specified negative air pressure differences. 1.2 This test method is intended to measure air leakage of a roof assembly with rooftop penetrations. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Quantification of Air Leakage in Low-Sloped Membrane Roof Assemblies