91.100.50 粘合料、密封材料 标准查询与下载

ASTM C1737-22 评估在配施前后温度对气溶胶泡沫密封剂的影响的标准指南

1.1 This guide covers the general effects of temperature from the aerosol foam sealant (either polyurethane or latex types) under the use temperatures. 1.2 The guide is intended to estimate the observed product dispensing characteristics and foam quality of aerosol foam dispensed or cured, or both, at specific temperatures and standard conditions. 1.3 Such foam sealants are primarily intended to reduce air movement in and out of building enclosures. 1.4 Currently two main foam sealant types are applicable to this standard: single component polyurethane and latex. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 There are no other known test methods specific for measuring the product temperature range for aerosol foam sealant. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Evaluating Temperature Effects to Aerosol Foam Sealant During and After Dispensing

22/30454331 DC BS EN 17872 用于防水的柔性片材 用于不连续屋顶覆盖物的衬垫 人工老化程序

BS EN 17872 Flexible sheets for waterproofing. Underlays for discontinuous roof coverings. Artificial ageing procedure

22/30454770 DC BS EN 17388-1 用于防水的柔性片材 环保产品声明 用于（屋顶）防水的沥青和合成柔性板材的产品类别规则 第 1 部分：从摇篮到坟墓

BS EN 17388-1. Flexible sheets for waterproofing. Environmental product declaration. Product Category Rules for bituminous and synthetic flexible sheets for (roof) waterproofing - Part 1. Cradle to grave

22/30454773 DC BS EN 17388-2 用于防水的柔性片材 环保产品声明 沥青和合成柔性板材的产品类别规则 第 2 部分：从摇篮到大门的选项

BS EN 17388-2. Flexible sheets for waterproofing. Environmental product declarations. Product Category Rules for bituminous and synthetic flexible sheets - Part 2. Cradle to gate with options

ASTM C1248-22 用接缝密封剂染色多孔基材的标准试验方法

1.1 This test method covers four types of laboratory tests to determine if a joint sealant has a probability of staining a porous substrate (such as marble, limestone, sandstone, granite, or other similar material). The tests are on compressed samples and include (1) storage under standard laboratory conditions, (2) storage in an oven, and (3) exposure in a fluorescent UV/condensation device, and (4) exposure in a xenon arc device. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This standard is similar, but not identical, to ISO 16938-1. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Staining of Porous Substrate by Joint Sealants

ASTM D7944-22 使用真空炉回收乳化沥青残留物的标准实施规程

1.1 This practice is suitable for recovery of the residue of emulsified asphalts composed principally of a semisolid or liquid asphaltic base, water, and an emulsifying agent. Asphalt base may be pre-modified with polymeric modifiers or latex polymer modifiers may be incorporated into the emulsified asphalt through co-milling or post emulsified asphalt production blending. 1.2 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Recovery of Emulsified Asphalt Residue Using a Vacuum Oven

ASTM C1489-15(2022) 结构用石灰腻子的标准规范

1.1 This specification covers lime putty products made from hydrated lime or quicklime products. Lime putty is suitable for use in masonry, plaster and stucco applications. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Lime Putty for Structural Purposes

ASTM D7703-22 使用水枪法在外露土工膜上确定漏电位置的标准实施规程

1.1 This practice is a performance-based standard for an electrical method for locating leaks in exposed geomembranes. For clarity, this practice uses the term “leak” to mean holes, punctures, tears, knife cuts, seam defects, cracks, and similar breaches in an installed geomembrane (as defined in 3.2.6). 1.2 This practice can be used for geomembranes installed in basins, ponds, tanks, ore and waste pads, landfill cells, landfill caps, canals, and other containment facilities. It is applicable for geomembranes made of materials such as polyethylene, polypropylene, polyvinyl chloride, chlorosulfonated polyethylene, bituminous geomembrane, and any other electrically insulating materials. This practice is best applicable for locating geomembrane leaks where the proper preparations have been made during the construction of the facility. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Electrical Leak Location on Exposed Geomembranes Using the Water Lance Method

ASTM D6630/D6630M-16(2022) 低坡度隔热屋顶膜组件性能的标准指南

1.1 This guide lists test methods intended to establish a minimum level of performance for insulated roof membrane assemblies, and lists pertinent design guidelines and installation methods in a unified manner. Material tests and evaluations are included with and without roof insulation. 1.2 It is not possible to establish a precise correlation between laboratory tests on roof assemblies and natural weathering due to variations in geographical climate, design, material, and installation. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Low-Slope Insulated Roof Membrane Assembly Performance

22/30454337 DC BS EN 13416 用于防水的柔性片材 用于屋顶防水的沥青、塑料和橡胶板 抽样规则

BS EN 13416. Flexible sheets for waterproofing. Bitumen, plastic and rubber sheets for roof waterproofing. Rules for sampling

ASTM D1188/D1188M-22 使用涂层样品测定压实沥青混合料的体积比重和密度的标准试验方法

1.1 This test method covers the determination of bulk specific gravity of specimens of Parafilm-coated, compacted asphalt mixtures. 1.2 This method should be used with samples that contain open or interconnecting voids or absorb more than 2.0 % of water by volume, or both. NOTE 1—A method for calculating the percent water absorbed by the specimen on a volume basis is described in Test Method D2726/D2726M. 1.3 The bulk specific gravity of the compacted asphalt mixtures may be used in calculating the unit weight of the mixture. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.5 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Bulk Specific Gravity and Density of Compacted Asphalt Mixtures Using Coated Samples

ASTM D7643-22 PG级配沥青粘合剂连续级配温度和连续级配测定的标准实施规程

1.1 This practice is used to estimate the continuous grading temperatures and continuous grade for an asphalt binder graded in accordance with the requirements specified in Specification D6373. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Determining the Continuous Grading Temperatures and Continuous Grades for PG Graded Asphalt Binders

ASTM C1472-16(2022) 确定密封剂接缝宽度时计算移动和其他影响的标准指南

1.1 This guide provides information on performance factors such as movement, construction tolerances, and other effects that should be accounted for to properly establish sealant joint size. It also provides procedures to assist in calculating and determining the required width of a sealant joint enabling it to respond properly to those movements and effects. Information in this guide is primarily applicable to singleand multicomponent, cold-applied joint sealants and secondarily to precured sealant extrusions when used with properly prepared joint openings and substrate surfaces. 1.2 Although primarily directed towards the understanding and design of sealant joints for walls for buildings and other areas, the information contained herein is also applicable to sealant joints that occur in horizontal slabs and paving systems as well as various sloped building surfaces. 1.3 This guide does not describe the selection and properties of joint sealants (1)2 , nor their use and installation, which is described by Guide C1193. 1.4 For protective glazing systems that are designed to resist blast and other effects refer to Guide C1564 in combination with this guide. 1.5 This guide is not applicable to the design of joints sealed with aerosol foam sealants. 1.6 For structural sealant glazing systems refer to Guide C1401 in combination with this guide. 1.7 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. SI units in this guide are in conformance with IEEE/ASTM SI 10-1997. 1.8 The Committee having jurisdiction for this guide is not aware of any comparable standards published by other organizations. 1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width

ASTM C711-22 单组分弹性溶剂释放型密封剂的低温柔韧性的标准试验方法

1.1 This test method covers determination of the lowtemperature flexibility and tenacity of one-part, elastomeric, solvent-release type sealants after cyclic highand lowtemperature aging. 1.2 The subcommittee with jurisdiction is not aware of any similar ISO standard. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Low-Temperature Flexibility and Tenacity of One-Part, Elastomeric, Solvent-Release Type Sealants

ASTM C1311-22 溶剂释放密封剂的标准规范

1.1 This specification describes the properties of a onecomponent solvent release sealant for use in building construction. These sealants are generally formulated to withstand a maximum joint movement of 7.5 % in extension and 7.5 % in compression of the nominal joint width. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 The committee with jurisdiction of this specification is not aware of any similar specification within ISO or any other organization. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Solvent Release Sealants

ASTM C1016-14(2022) 测定密封剂衬垫（接缝填料）材料吸水率的标准试验方法

1.1 This test method covers a laboratory procedure for determining the water absorption characteristics of sealant backing and joint filler materials, hereinafter referred to as backing. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.3 The committee with jurisdiction over this standard is not aware of any comparable standards published by other ASTM committees or other organizations. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Water Absorption of Sealant Backing (Joint Filler) Material

ASTM C1401-14(2022) 结构密封胶玻璃的标准指南

1.1 Structural sealant glazing, hereinafter referred to as SSG, is an application where a sealant not only can function as a barrier against the passage of air and water through a building envelope, but also primarily provides structural support and attachment of glazing or other components to a window, curtain wall, or other framing system. 1.2 This guide provides information useful to design professionals, manufacturers, contractors, and others for the design and installation of a SSG system. This information is applicable only to this glazing method when used for a building wall that is not more than 15° from vertical; however, limited information is included concerning a sloped SSG application. 1.3 Only a silicone chemically curing sealant specifically formulated, tested, and marketed for structural sealant glazing is acceptable for a SSG system application. 1.4 The committee with jurisdiction for this standard is not aware of any comparable standard published by other organizations. 1.5 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. SI units in this guide are in conformance with IEEE/ASTM SI 10. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Structural Sealant Glazing

BS ISO 4781:2022 建筑和土木工程密封剂 应用寿命的测定

1   Scope The document specifies a method for the determination of application life of multi-component sealants. NOTE The application life test method is only applicable to multi-part sealants.

Building and civil engineering sealants. Determination of application life

GSO ISO 23658:2022 建筑物和土木工程 密封剂 使用珠剥离试验测试粘合性能

The document specifies a method for evaluating the adhesion of sealants with a minimum elongation at break of 25 % (according to ISO 8339, Method A or B) on various substrates. This test method can be used for one-component and multi component sealants. This method is typically used for elastic sealants but can be also used for plastic sealants. For plastic sealants, the test can be more difficult and needs to be carried out by experienced technicians. This test is used to judge the adhesion of construction sealants in combination with cleaners, activators and/or primers on various substrates when exposed to a peeling force and also after different aging conditions. An adhesion test according to this document can also be conducted for process monitoring and quality assurance accompanying production. The test method described in this document is not intended to replace any adhesion cohesion test methods specified in ISO 11600.

Buildings and civil engineering works — Sealants — Testing of adhesion properties using a bead peel test

GSO ASTM C1315:2022 用于固化和密封混凝土的具有特殊性能的液膜形成化合物的标准规范

This specification covers the performance requirements for membrane-forming liquids suitable for use as curing compounds and sealers for fresh and hardened concrete. Each membrane should have good alkali resistance, acid resistance, adhesion-promoting qualities, and resistance to degradation by UV light. The materials are limited to clear or translucent and white pigmented materials, all of which are classified into non-yellowing, moderately yellowing, or yellows or darkens unrestrictedly.

Standard Specification for Liquid Membrane-Forming Compounds Having Special Properties for Curing and Sealing Concrete