91.100.50 粘合料、密封材料 标准查询与下载

ASTM C919-22 声学应用中密封剂使用的标准实施规程

1.1 This practice provides information for the use of sealants to reduce sound transmission characteristics of interior walls, ceilings, and floors by proper application of sealants to joints, voids, and penetrations normally found in building construction, which are commonly referred to as airborne sound flanking paths. 1.2 The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations. 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.4 This standard does not purport to address fire stopping or safing requirements for joints, voids, and penetrations through fire-rated wall, ceiling, and floor assemblies. Additional requirements may be necessary for fire-rated assemblies to meet the applicable building code provisions. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Use of Sealants in Acoustical Applications

ASTM C712-22 单组分弹性体溶剂释放型密封剂起泡的标准试验方法

1.1 This test method covers determination of the degree of bubble formation or surface blistering in one-part, elastomeric solvent-release type sealants when exposed to elevated temperatures. 1.2 The subcommittee with jurisdiction is not aware of any similar ISO standard. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Bubbling of One-Part, Elastomeric, Solvent-Release Type Sealants

ASTM C836/C836M-18(2022) 与单独磨耗层一起使用的高固体含量冷液体应用弹性防水膜的标准规范

1.1 This specification describes the required properties and test methods for a cold liquid-applied elastomeric-type membrane, oneor two-component, for waterproofing building decks and walls subject to hydrostatic pressure in building areas to be occupied by personnel, vehicles, or equipment. This specification applies only to a membrane system that will be covered with a separate wearing course, traffic course, or backfill. NOTE 1—See Guides C898/C898M and C1471/C1471M for proper application of membrane. 1.2 There are no ISO standards similar or equivalent to this ASTM standard. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane for Use with Separate Wearing Course

ASTM C731-15(2022) 乳胶密封剂包装老化后可挤压性的标准试验方法

1.1 This test method covers a laboratory procedure for the determination of extrudability of latex sealants after freezethaw and heat cycling. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—Currently there is no ISO standard similar to this test method. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Extrudability, After Package Aging, of Latex Sealants

ASTM D2042-22 沥青材料在三氯乙烯或甲苯中溶解度的标准试验方法

1.1 This test method covers the determination of the degree of solubility in trichloroethylene or toluene of asphalt materials having little or no mineral matter. NOTE 1—This method is not applicable to tars and their distillation residues or highly cracked petroleum products. For methods covering tars, pitches, and other highly cracked petroleum products, and the use of other solvents, see Test Methods D4, D2318, and D2764. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precaution statements are given in Section 7. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Solubility of Asphalt Materials in Trichloroethylene or Toluene

DIN 18545:2022 用密封剂密封玻璃 回扣和玻璃系统的要求

This standard deals with the sealing of glazing with sealants and specifies requirements for the rebates of windows and doors for the installation of glazing units (single glazing or insulating glass units (IGUs)). It applies to: - linearly supported glazing for windows and doors

Sealing of glazing with sealants - Requirements for rebates and glazing systems

DIN CEN/TS 17659:2022 机械固定屋顶防水系统设计指南；德文版 CEN/TS 17659:2021

This document gives guidance for the design of a roof waterproofing system mechanically fastened to the structural deck in relation to wind load resistance.This document is intended to be used together with EN 16002 and the relevant clauses of EAD-030351-00-0402-2019.This guideli

Design guideline for mechanically fastened roof waterproofing systems; German version CEN/TS 17659:2021

ASTM D4311/D4311M-21 测定沥青体积对基础温度修正的标准实施规程

1.1 This practice provides tables of volume correction factors which may be used to convert volumes of asphalt measured at different temperatures to a volume at a standard base temperature. These tables are applicable to all types of asphalts except emulsified asphalts. 1.2 This practice provides tables to convert asphalt volumes to 15 °C [60 °F] from volumes measured at any temperature from −25 to +275 °C [0 to 500 °F]. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. NOTE 1—Correction factors in Table 1 and Table 2 are for use in place of correction factors provided in Guide D1250, which do not address requirements for asphalt specifications.2 1.4 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Determining Asphalt Volume Correction to a Base Temperature

ASTM D4887/D4887M-11(2021)e1 热再生沥青材料用粘度混合物制备的标准实施规程

1.1 This practice covers the procedure for preparation of hot recycled bituminous blends for testing in the laboratory. The procedure involves an iterative trial blend process followed by the preparation of batch blends. 1.2 The batch blends can be used for extensive evaluation such as viscosity, penetration, ductility, aging properties (such as Rolling Thin Film Oven or Thin-Film Oven tests, or both (RTFO/TFO)), composition analysis, solubility analysis, and other user-selected tests. 1.3 This practice assumes that a representative reclaimed asphalt pavement (RAP) sample is extracted and the aged binder recovered using Test Methods D2172/D2172M and Test Method D1856 (this practice may be modified by using a rotary evaporator which is extensively evaluated in the minutes of the 18th Pacific Coast Conference on Asphalt Specifications2 ) or any other acceptable test method. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.5 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Preparation of Viscosity Blends for Hot Recycled Asphalt Materials

ASTM D2028/D2028M-15(2021)e1 稀释沥青（快速固化型）的标准规范

1.1 This specification covers cutback petroleum asphalts of the rapid-curing type for use in the construction and treatment of pavements. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Cutback Asphalt (Rapid-Curing Type)

ASTM D5405/D5405M-98(2021) 用非沥青有机屋顶膜材料制成的接头进行失效时间（蠕变断裂）试验的标准试验方法

1.1 This test method covers laboratory determination of the time-to-failure (creep-rupture) of joints fabricated from nonbituminous organic roof membrane material. The test method covers both T-peel and lap-shear joints subjected to constant tensile load under controlled environmental conditions. The joints, made from either unreinforced or fabric-reinforced membrane material, are prepared in the laboratory or sampled from roofs in service. 1.2 Sheet materials from which the joints are fabricated include vulcanized rubbers, nonvulcanized polymeric sheets, and thermoplastics. The bonding methods for joint formation include the use of liquid-based adhesives, preformed tapes, and thermal and solvent weld processes. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Conducting Time-to-Failure (Creep-Rupture) Tests of Joints Fabricated from Nonbituminous Organic Roof Membrane Material

ASTM D6223/D6223M-21 使用聚酯和玻璃纤维增强物组合的无规聚丙烯（APP）改性沥青片材的标准规范

1.1 This specification covers prefabricated modified bituminous sheet materials reinforced with a combination of polyester fabric and glass fiber, with or without granules, that use atactic polypropylene (APP) as the primary modifier and are intended for use in the fabrication of multiple ply roofing and waterproofing membranes. 1.2 This specification is intended as a material specification only. Issues regarding the suitability of specific roof constructions or application techniques are beyond the scope of this specification. 1.3 The specified tests and property limits used to characterize the sheet materials covered by this specification are intended to establish minimum properties. In-place roof system design criteria such as fire resistance, field strength, impact/ puncture resistance, material compatibility, uplift resistance, the need for field applied coatings, and others, are factors beyond the scope of this material specification. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Atactic Polypropylene (APP) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcements

ASTM D6162/D6162M-21 使用聚酯和玻璃纤维增强物组合的苯乙烯-丁二烯-苯乙烯（SBS）改性沥青片材的标准规范

1.1 This specification covers prefabricated modified bituminous sheet materials reinforced with a combination of polyester fabric and glass fiber, with or without granules, which use styrene butadiene styrene (SBS) thermoplastic elastomer as the primary modifier and are intended for use in the fabrication of multiple ply roofing and waterproofing membranes. 1.2 This specification is intended as a material specification only. Issues regarding the suitability of the specific roof constructions or application techniques are beyond this scope. 1.3 The specified tests and property limits used to characterize the sheet materials are intended to establish minimum properties. In-place roof system design criteria such as fire resistance, field strength, impact/puncture resistance, material compatibility, uplift resistance, and others, are factors beyond the scope of this material specification. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcements

ASTM D6163/D6163M-21 使用玻璃纤维增强的苯乙烯-丁二烯-苯乙烯（SBS）改性沥青薄板材料的标准规范

1.1 This specification covers prefabricated modified bituminous sheet materials with glass fiber reinforcement, with or without granules, that use styrene butadiene styrene (SBS) thermoplastic elastomer as the primary modifier and are intended for use in the fabrication of multiple ply roofing and waterproofing membranes. 1.2 This specification is intended as a material specification only. Issues regarding the suitability of the specific roof constructions or application techniques are beyond this scope. 1.3 The specified tests and property limits used to characterize the sheet materials are intended to establish minimum properties. In-place roof system design criteria, such as fire resistance, field strength, impact/puncture resistance, material compatibility, uplift resistance, and others, are factors beyond the scope of this material specification. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using Glass Fiber Reinforcements

DIN EN 16002:2021 防水用柔性板 屋顶防水用机械固定柔性板抗风载荷的测定；德文版 EN 16002:2018 + AC:2021

This document specifies a test method to determine the resistance to wind load of mechanically fastened flexible sheets for roof waterproofing.

Flexible sheets for waterproofing - Determination of the resistance to wind load of mechanically fastened flexible sheets for roof waterproofing; German version EN 16002:2018 + AC:2021

DIN EN ISO 11432:2021 建筑和土木工程密封剂 抗压性的测定（ISO 11432:2021）；德文版 EN ISO 11432:2021

The document specifies a method for determining the pressure resistance of sealants used for sealing joints in building construction.

Building and civil engineering sealants - Determination of resistance to compression (ISO 11432:2021); German version EN ISO 11432:2021

BS EN 16002:2018 用于防水的柔性片材 屋顶防水机械固定柔性板抗风载荷的测定

What is BS EN 16002 - Flexible sheets for waterproofing about?   BS EN 16002 is a European standard that discusses flexible sheets for waterproofing. BS EN 16002 specifies a test method to determine the resistance to wind load of mechanically fastened flexible sheets for roof waterproofing.   BS EN 16002 assessment is limited to the performance of the mechanically fastened flexible sheets only.   Note-   BS EN 16002 does not include the determination of the performance of the mechanical fastener and/or the combination of the mechanical fastener and the substrate. 

Flexible sheets for waterproofing. Determination of the resistance to wind load of mechanically fastened flexible sheets for roof waterproofing

BS EN ISO 10591:2021 建筑和土木工程密封剂 密封剂浸入水中后的粘附/内聚性能的测定

What is ISO 10591 about?    ISO 10591 specifies a method for the determination of the influence of water on the adhesion/cohesion properties of sealants with predominantly plastic behaviour which are used in joints in buildings and civil engineering works.   Who is ISO 10591 for?   ISO 10591 on the determination of adhesion /cohesion properties of sealants is useful for:   Manufacturers of sealants  

Building and civil engineering sealants. Determination of adhesion/cohesion properties of sealants after immersion in water

T/ZZXJX 038-2021 建筑用气密性材料应用技术规程

前  言　 1 范围　 2 规范性引用文件　 3 术语和定义　 4 一般规定　 5 技术要求　 6 设计　 7 施工　     7.1 施工准备　     7.2 施工作业　     7.3 外门窗气密性施工　     7.4 穿外围护结构管道气密性施工　     7.5 其他部位气密性施工　 8 验收　     8.1 一般规定　     8.2 主控项目　     8.3 一般项目　

Technical specification for the application of airtight materials for buildings

ASTM D5665/D5665M-99a(2021) 冷用屋顶和防水用热塑性织物的标准规范

1.1 This specification covers thermoplastic fabrics such as polyester, polyester/polyamide bicomponent, or composites with fiberglass or polyester scrims that can be used during the construction of cold-applied roofing and waterproofing. 1.2 This specification is intended as a material specification. Issues regarding the suitability of specific roof constructions or application techniques are beyond the scope of this specification. 1.3 The specified tests and property values used to characterize the respective fabrics are intended to establish minimum properties. In-place system design criteria or performance attributes are factors beyond the scope of this material specification. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Thermoplastic Fabrics Used in Cold-Applied Roofing and Waterproofing