91.100.50 粘合料、密封材料 标准查询与下载

ASTM D5665/D5665M-99a(2021) 冷用屋顶和防水用热塑性织物的标准规范

1.1 This specification covers thermoplastic fabrics such as polyester, polyester/polyamide bicomponent, or composites with fiberglass or polyester scrims that can be used during the construction of cold-applied roofing and waterproofing. 1.2 This specification is intended as a material specification. Issues regarding the suitability of specific roof constructions or application techniques are beyond the scope of this specification. 1.3 The specified tests and property values used to characterize the respective fabrics are intended to establish minimum properties. In-place system design criteria or performance attributes are factors beyond the scope of this material specification. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Thermoplastic Fabrics Used in Cold-Applied Roofing and Waterproofing

ASTM D6221/D6221M-00(2021) 屋面和防水用增强沥青防水板的标准规范

1.1 This specification covers factory-prepared reinforced bituminous sheet used in flashing. The bitumen used may be asphalt, coal-tar pitch, or polymer-modified bitumen. The reinforcement may include any one or a combination of organic (wood fiber), polyester, or glass fiber felts, woven fabrics, or thermoplastic films. Fine mineral powders, granules, or metal foils may be used as surfacing. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 The following precautionary statement pertains only to the test method portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Reinforced Bituminous Flashing Sheets for Roofing and Waterproofing

ASTM D3909/D3909M-14(2021) 表面有矿物颗粒的沥青卷材（玻璃毡）的标准规范

Standard Specification for Asphalt Roll Roofing (Glass Felt) Surfaced with Mineral Granules

CEN/TS 17659:2021 机械固定屋顶防水系统设计指南

This document gives guidance for the design of a roof waterproofing system mechanically fastened to the structural deck in relation to wind load resistance. This document is intended to be used together with EN 16002 and the relevant clauses of EAD-030351-00-0402-2019. This guideline does not include the seperate fastening requirements of the insulation boards, the securement to upstands, perimeter fastening, flashings or other roof details.

Design guideline for mechanically fastened roof waterproofing systems

ASTM D7281-07(2021) 测定穿过屋顶薄膜的水迁移阻力的标准试验方法

1.1 This test method covers the determination of water migration resistance of roof membranes including built-up roof membranes, modified bitumen, and single-ply roof membranes. The procedures were developed to determine the potential for leakage of water through the roof membranes resulting from a standing head of water and when pressurized with air from the underside. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining Water Migration Resistance Through Roof Membranes

ASTM D5404/D5404M-21 使用旋转蒸发器从溶液中回收沥青粘合剂的标准实施规程

1.1 This practice is intended to recover asphalt from a solvent using the rotary evaporator to ensure that changes in the asphalt properties during the recovery process are minimized. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.2.1 Residual pressure measurements are shown in both the SI unit of kPa and the commonly used non-standard equivalent unit of “mm of Hg.” 1.2.2 Measurements of volume and mass are only given in SI units because they are the only units typically used in practice when performing this standard practice. 1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Recovery of Asphalt Binder from Solution Using the Rotary Evaporator

ASTM D2872-21 热和空气对沥青移动膜影响的标准试验方法（滚动薄膜烘箱试验）

Standard Test Method for Effect of Heat and Air on a Moving Film of Asphalt (Rolling Thin-Film Oven Test)

ASTM D3141/D3141M-21 波特兰水泥混凝土路面底层密封用沥青的标准规范

1.1 This specification covers asphalt suitable for undersealing portland-cement concrete and overlaid concrete pavements by pumping hot asphalt under the slabs. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Asphalt for Undersealing Portland-Cement Concrete Pavements

ASTM D2399-21 稀释沥青选择的标准实施规程

1.1 This practice covers the selection of cutback asphalts of the slow, medium, and rapid curing types for various paving and allied uses. Slow-curing cutback asphalts are also called road oils. 1.2 The values stated in either SI units or English units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Selection of Cutback Asphalts

ASTM D5710/D5710M-21 特立尼达湖改性沥青标准规范

Standard Specification for Trinidad Lake Modified Asphalt

EN ISO 10591:2021 房屋建筑.密封胶.浸水后密封胶的粘结/粘合性能测定

Building and civil engineering sealants - Determination of adhesion/cohesion properties of sealants after immersion in water (ISO 10591:2021)

DS/ISO 11432:2021 建筑与土木工程用密封胶 抗压性的测定

Building and civil engineering sealants – Determination of resistance to compression

T/CECS 10158-2021 天冬聚脲美缝剂

本文件规定了天冬聚脲美缝剂的术语和定义，分类和标记，技术要求，试验方法，检验规则及标志，包装、运输和贮存。

aspart polyurea joint agent

T/CECS 10157-2021 混凝土粘度调节剂

本文件规定了混凝土粘度调节剂的术语和定义，分类与标记，要求，试验方法，检验规则，标志、包装、运输与贮存。

Concrete Viscosity Regulator

BS EN ISO 11432:2021 建筑和土木工程密封剂 抗压缩性的测定

Building and civil engineering sealants. Determination of resistance to compression

DS/EN ISO 11432:2021 建筑和土木工程密封胶 抗压缩性的测定（ISO 11432:2021）

Building and civil engineering sealants – Determination of resistance to compression (ISO 11432:2021)

BS EN ISO 9046:2021 建筑和土木工程密封剂 恒温下粘合/内聚性能的测定

Building and civil engineering sealants. Determination of adhesion/cohesion properties at constant temperature

ISO 10591:2021 建筑和土木工程密封剂.浸入水中后密封剂粘附/粘合性能的测定

This document specifies a method for the determination of the influence of water on the adhesion/ cohesion properties of sealants with predominantly plastic behaviour which are used in joints in buildings and civil engineering works.

Building and civil engineering sealants — Determination of adhesion/cohesion properties of sealants after immersion in water

DS/EN 16002:2021 防水用柔性板材 屋顶防水用机械固定柔性板材抗风荷载性能的测定

Flexible sheets for waterproofing – Determination of the resistance to wind load of mechanically fastened flexible sheets for roof waterproofing

ISO 11432:2021 建筑和土木工程密封剂.抗压性的测定

This document specifies a method for the determination of the resistance to compression of sealants used in joints in buildings and civil engineering works.

Building and civil engineering sealants — Determination of resistance to compression