91.100.50 粘合料、密封材料 标准查询与下载
共找到 1899 条与 粘合料、密封材料 相关的标准，共 127 页
ISO 11528:2016 specifies methods for the assessment of surface defects (crazing and cracking) on sealants after exposure to artificial or natural weathering.
Buildings and civil engineering works — Sealants — Determination of crazing and cracking following exposure to artificial or natural weathering
- ICS
- 91.100.50
- CCS
- 发布
- 2021-07-01
- 实施
This specification covers the properties of a cured single- or multicomponent cold-applied elastomeric joint sealant for sealing, caulking, or glazing operations on buildings, plazas, and decks for vehicular or pedestrian use, and types of construction other than highway and airfield pavements and bridges. A sealant qualifying under this specification shall be classified as to type, grade, class and use as follows: type S - a single-component sealant, type M - a multicomponent sealant, grade P - a pourable or selfleveling sealant, grade NS - a nonsag or gunnable sealant, class 100/50, class 50, class 35, class 25, class 12.5, use T, use NT, use I, use M, use G, use A, and use O. A single-component sealant shall be a uniform mixture of a consistency suitable for immediate application by hand or pressure caulking gun or by hand tool. A multicomponent chemically curing sealant shall be furnished in two or more components. A single-component and multicomponent sealant, when stored in the original unopened container at temperatures of not more than 27°C (80°F) shall be capable of meeting the requirements for at least 6 months after date of delivery. Grade P (pourable or selfleveling) sealant shall have the required flow characteristics, it shall exhibit a smooth, level surface. Grade NS or gunnable sealant shall have the required flow characteristics such that when tested in vertical displacement. Type S, grade P, and grade NS sealant shall not be less than the given extrusion rate when tested. Type M and grade P sealant, when tested shall be not less than the given extrudable rate 3 h after mixing. Use T (traffic) sealant shall have a hardness reading, after being properly cured, of not less than 25 or more than 50 when tested. Use NT (nontraffic) sealant shall have a hardness reading, after being properly cured, of not less than 15 or more than 50 when tested. The sealant shall not lose more than 7 % of its original weight or show any cracking or chalking when tested. There shall be no transfer of the sealant to the polyethylene film when tested at 72 h. The sealant shall not cause any visible stain on the top surface of a white cement mortar base when tested. The adhesion and cohesion after cyclic movement shall be tested to meet the requirements prescribed. The adhesion-in-peel test shall be performed to meet the requirements precribed. The adhesion-in-peel after ultraviolet exposure through glass shall be determined to meet the requirements prescribed. The accelerated weathering effects, and sealants exposed to continuous immersion shall be determined to meet the requirements prescribed.
Standard Specification for Elastomeric Joint Sealants
- ICS
- 91.100.50
- CCS
- 发布
- 2021-07-01
- 实施
This European Standard specifies the determination of the visible defects of bitumen sheets for roofing, which could influence the functional behaviour of these sheets.
Flexible sheets for waterproofing - Determination of visible defects - Part 1: Bitumen sheets for roof waterproofing
- ICS
- 91.100.50
- CCS
- 发布
- 2021-07-01
- 实施
This European Standard specifies methods for the determination of length, width, straightness and flatness of thermoplastic and elastomeric sheets for roof waterproofing.
Flexible sheets for waterproofing - Determination of length, width, straightness and flatness - Part 2: Plastic and rubber sheets for roof waterproofing
- ICS
- 91.100.50
- CCS
- 发布
- 2021-07-01
- 实施
This document specifies methods for the determination of the thickness and mass per unit area of plastic and rubber sheets for roof waterproofing.
Flexible sheets for waterproofing - Determination of thickness and mass per unit area - Part 2: Plastics and rubber sheets for roof waterproofing
- ICS
- 91.100.50
- CCS
- 发布
- 2021-07-01
- 实施
-
Bitumen and bituminous binders. Framework for specification of oxidised bitumen
- ICS
- 91.100.50
- CCS
- 发布
- 2021-07-01
- 实施
ISO 19861:2015 specifies a method for the determination of the curing behaviour of sealants used in joints in building construction.
Buildings and civil engineering works — Sealants — Determination of curing behaviour
- ICS
- 91.100.50
- CCS
- 发布
- 2021-07-01
- 实施
This European Standard specifies the general rules how to select the samples of bitumen, plastic or rubber sheets for roof waterpoofing from which the test pieces are taken. lt also specifies the conditioning procedures to be followed before the test piece is cut from the sample. This standard is appliable in conjunction with product charateristics on bitumen, plastic and rubber sheets for roof waterproofing from which the test specimens are taken.
Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Rules for sampling
- ICS
- 91.100.50
- CCS
- 发布
- 2021-07-01
- 实施
ISO 19862:2015 specifies a method for the determination of classification of durability of sealants used in exterior joints in building construction.
Buildings and civil engineering works — Sealants — Durability to extension compression cycling under accelerated weathering
- ICS
- 91.100.50
- CCS
- 发布
- 2021-07-01
- 实施
This European Standard specifies a methods for the determination of "overall thickness" (method A) and "overall or component thickness" (method B) and "mass per unit area" of bitumen sheets for roofing. The determination of overall thickness by method A is only applicable to unembossed sheets. The determination of overall thickness by method B is applicable to embossed and unembossed sheets and can also be used for composite thickness measurements.
Flexible sheets for waterproofing - Determination of thickness and mass per unit area - Part 1: Bitumen sheets for roof waterproofing
- ICS
- 91.100.50
- CCS
- 发布
- 2021-07-01
- 实施
This European Standard specifies methods for the determination of the visible defects of thermoplastic and elastomeric sheets for waterproofing, which could influence the functional behaviour of these sheets.
Flexible sheets for waterproofing - Determination of visible defects - Part 2: Plastic and rubber sheets for roof waterproofing
- ICS
- 91.100.50
- CCS
- 发布
- 2021-07-01
- 实施
This European Standard specifies a method for the determination of the length, width and straightness of bitumen sheets for roofing.
Flexible sheets for waterproofing - Determination of length, width and straightness - Part 1: Bitumen sheets for roof waterproofing
- ICS
- 91.100.50
- CCS
- 发布
- 2021-07-01
- 实施
-
Standard Guide for Use of Joint Sealants
- ICS
- 91.100.50
- CCS
- 发布
- 2021-07-01
- 实施
ISO 11618:2015 applies to sealants used for pedestrian walkways, public areas, movement joints between concrete slabs, areas with pedestrian load, areas which are used with trolleys, parking garages, walkable floors, balconies, terraces, and warehouses. This International Standard specifies the types and classes of elastic sealants used in building construction pedestrian walkways according to their performance characteristics. Sealant may be either non-sag or self-leveling as declared by the manufacturer. Areas of application are floor joints which have been designed. Chemical containment, cold applied joint sealants for concrete pavements to be used in roads, airfields, and sewage treatment plants are excluded. Local regulations may be required in addition to this International Standard based on local laws and codes.
Buildings and Civil Engineering Works — Sealants — Classification and requirements for pedestrian walkway sealants
- ICS
- 91.100.50
- CCS
- 发布
- 2021-07-01
- 实施
-
Standard Test Methods and Practices for Emulsified Asphalts
- ICS
- 91.100.50
- CCS
- 发布
- 2021-07-01
- 实施
ISO/TR 20436:2017 reviews and evaluates the methodology that can be employed to assess the paintability of or paint compatibility with sealants used in building and construction. The term "paintability" is used throughout this document and is a generic term to refer to the application of paint or a coating to a sealant.
Buildings and civil engineering works — Sealants — Paintability and paint compatibility of sealants
- ICS
- 91.100.50
- CCS
- 发布
- 2021-07-01
- 实施
1.1 This guide covers the general use of aerosol polyurethane and aerosol latex foams extruded from pressurized containers intended for building envelope air barrier sealant and adhesive applications in building construction. It also provides an overview of associated standards and test methods that quantify key physical properties that are useful to design professionals, engineers, specifiers, and end users. 1.2 Currently two main foam sealant types are applicable to this practice, single component polyurethane and latex types. 1.3 The values stated in inch-pound units are to be regarded as standard. SI units provided are for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific safety considerations see Section 7. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Guide for Product Selection/Delivery Systems for Aerosol Foam Sealants and Adhesives
- ICS
- 91.100.50
- CCS
- 发布
- 2021-07-01
- 实施
This specification covers the requirements for thirteen grades of emulsified asphalt for use in pavement construction in the manner designated. The emulsified asphalts shall be homogeneous after thorough mixing and shall be tested within 14 days of delivery. Asphalts separated by freezing shall no longer be tested. Materials shall be appropriately sampled and tested, and shall conform accordingly to the following physical requirements: viscosity; storage stability; demulsibility; coating ability and water resistance; cement mixing; residue by distillation; oil distillate; ductility; solubility in trichloroethylene; and behavior during sieve, penetration, and float tests.
Standard Specification for Emulsified Asphalt
- ICS
- 91.100.50
- CCS
- 发布
- 2021-07-01
- 实施
Buildings and civil engineering sealants - Vocabulary (ISO 6927:2021)
- ICS
- 91.100.50
- CCS
- 发布
- 2021-06-30
- 实施
- 2021-06-30
Building and civil engineering sealants - Determination of adhesion/cohesion properties at constant temperature (ISO 9046:2021)
- ICS
- 91.100.50
- CCS
- 发布
- 2021-06-15
- 实施
- 2021-06-15
