91.100.50 粘合料、密封材料 标准查询与下载

ASTM D7425/D7425M-13(2019) 用于屋顶应用的喷涂聚氨酯泡沫的标准规范

1.1 This specification covers the types and physical properties of spray polyurethane foam (SPF) for use in SPF roofing applications. 1.2 This specification does not provide guidance for application. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Spray Polyurethane Foam Used for Roofing Applications

T/GZBC 25-2019 硅烷改性硅酮建筑密封胶

本标准规定了硅烷改性硅酮建筑密封胶产品的术语和定义、分类、要求、试验方法、检验规则、标志、包装、运输和贮存。

Silane modified silicone sealant for building

ASTM D71-94(2019) 固体沥青和沥青相对密度的标准试验方法（置换法）

1.1 This test method covers the determination of relative density by water displacement of hard pitches and asphalts with softening points above 70 °C. 1.2 The relative density of hard pitch and asphalt shall be determined, whenever possible, on homogeneous natural fragments free of cracks. The use of cast cubes is not recommended due to the difficulty of avoiding incorporation of air bubbles. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Relative Density of Solid Pitch and Asphalt (Displacement Method)

ASTM D2027/D2027M-19 切割沥青（中等固化型）的标准规格

1.1 This specification covers cutback petroleum asphalts of the medium-curing type for use in the construction and treatment of pavements. 1.2 The values stated in SI units or inch-pounds are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of each other. Combining values from the two systems may result in nonconformance with the standard. 1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Cutback Asphalt (Medium-Curing Type)

ASTM D7349/D7349M-15(2019) 确定屋顶和防水材料在紧固件周围密封的能力的标准测试方法

1.1 This qualitative test method determines the capability of asphalt-based roofing or waterproofing material to seal around a fastener that penetrates the material and prevent transmission of liquid water through the material at the penetration under defined conditions. 1.2 This test method is provided for adoption by ASTM or other consensus-based roofing and waterproofing product specifications as a standardized means to evaluate capability to seal around a fastener. Performance of this test method after subjecting the product to conditioning intended to simulate environmental stresses and strains is not prohibited. 1.3 The text of this test method references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining the Capability of Roofing and Waterproofing Materials to Seal Around Fasteners

ASTM D545-19 混凝土结构用预制伸缩缝填料的标准试验方法（非挤压型和弹性型）

1.1 These test methods cover the physical properties associated with preformed expansion joint fillers. The test methods include: Property Section Expansion in Boiling Water 7.1 Recovery and Compression 7.2 Extrusion 7.3 Boiling in Hydrochloric Acid 7.4 Asphalt Content 7.5 Water Absorption 7.6 Density 7.7 NOTE 1—Specific test methods are applicable only to certain types of joint fillers, as stated herein. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Preformed Expansion Joint Fillers for Concrete Construction (Nonextruding and Resilient Types)

ASTM D1669/D1669M-07(2019) 沥青涂料加速和户外耐候试验板的制备标准做法

1.1 This practice covers a procedure for the preparation of accelerated and outdoor weathering test panels of bituminous coatings. It is considered suitable for the preparation of film thicknesses in the range from 0.25 to 2.54 mm [0.010 to 0.100 in.]. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. (Warning—Mercury has been designated by EPA and many state agencies as a hazardous material that can cause central nervous system, kidney, and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercurycontaining products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPA’s website, http://www.epa.gov/mercury/faq.htm, for additional information. Users should be aware that selling mercury or mercurycontaining products, or both, in your state may be prohibited by state law.) 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Preparation of Test Panels for Accelerated and Outdoor Weathering of Bituminous Coatings

ASTM D977-19ae1 乳化沥青的标准规格

Standard Specification for Emulsified Asphalt

ASTM D1369-19 沥青集料表面处理用材料量的标准实施规程

1.1 This practice covers the rates of application of asphalt materials and aggregates and types and grades of asphalt materials for single and multiple asphalt surface treatments as applied to suitably prepared pavements or bases. 1.2 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Quantities of Materials for Asphalt-Aggregate Surface Treatments

ASTM D2397/D2397M-19a 阳离子乳化沥青的标准规范

Standard Specification for Cationic Emulsified Asphalt

ASTM D977-19a 乳化沥青的标准规格

Standard Specification for Emulsified Asphalt

ASTM D3161/D3161M-19a 陡坡屋顶产品抗风性的标准试验方法（风扇感应法）

Standard Test Method for Wind Resistance of Steep Slope Roofing Products (Fan-Induced Method)

ASTM C734-15(2019) 人工风化胶乳密封剂低温柔韧性的标准试验方法

1.1 This test method covers a laboratory procedure for the determination of low-temperature flexibility of latex sealants after 500 h artificial weathering. 1.2 The values stated in metric (SI) units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—Currently there is no ISO standard similar to this test method. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Low-Temperature Flexibility of Latex Sealants After Artificial Weathering

ASTM D2452-15(2019) 油基和树脂基填缝化合物可挤压性的标准试验方法

1.1 This test method describes the laboratory procedure for determining the rate of extrusion of oiland resin-base caulking compounds. 1.2 The values stated in metric (SI) units are to be regarded as the standard. The values given in parentheses are provided for information only. 1.3 The subcommittee with jurisdiction is not aware of any similar ISO standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Extrudability of Oil- and Resin-Base Caulking Compounds

BS ISO 16938-2:2019 建筑物和土木工程 接缝中使用的密封剂对多孔基材染色的测定 无压缩测试

What is ISO 16938 ‑ 2 - Buildings and civil engineering works about?   ISO 16938-2 discusses the determination of the straining of porous substrates by sealants used in joints for building, and civil engineering works.   ISO 16938 ‑ 2 is the second part of the ISO 16938 series that specifies a method for determining the staining of porous substrates (e.g., marble, limestone, sandstone, or granite) by sealants used in building construction. The method evaluates the likelihood of a sealant causing an early stain on a porous substrate due to the exudation of materials from the sealant.   The outcome of the test is specific to the tested sealant, and tested substrate, and cannot be extrapolated to other sealant formulations or other porous substrates. During this accelerated test, if the sealant does not stain or discolour the substrates, it does not mean that the tested sealant will not stain or discolour the tested porous substrate over a longer period.   ...

Buildings and civil engineering works. Determination of the staining of porous substrates by sealants used in joints - Test without compression

BS ISO 16938-1:2019 建筑物和土木工程 接缝中使用的密封剂对多孔基材染色的测定 压缩试验

What is ISO 16938 ‑ 1 – Buildings and civil engineering works about?   ISO 16938 is an international standard on building applications that discusses the determination of the staining of porous substrates by sealants used in joints for buildings and civil engineering works.   ISO 16938 ‑ 1 is the first part of ISO 16938 which specifies a method for determining the staining of porous substrates (e.g., marble, limestone, sandstone or granite) by sealants used in building construction. The method evaluates the likelihood of a sealant causing an early stain on a porous substrate due to the exudation of materials from the sealant. The outcome of the test is spec...

Buildings and civil engineering works. Determination of the staining of porous substrates by sealants used in joints - Test with compression

ISO 16938-1:2019 建筑和土木工程 - 通过密封剂在接头中测定多孔基材的染色 - 第1部分:压缩试验

This document specifies a method for determining the staining of porous substrates (e.g. marble, limestone, sandstone or granite) by sealants used in building construction. The method evaluates the likelihood of a sealant causing an early stain on a porous substrate due to exudation of materials from the sealant. The outcome of the test is specific to the tested sealant and tested substrate and cannot be extrapolated to other sealant formulations or other porous substrates. During this accelerated test, if the sealant does not stain or discolour the substrates, it does not mean that the tested sealant will not stain or discolour the tested porous substrate over a longer time period.

Buildings and civil engineering works — Determination of the staining of porous substrates by sealants used in joints — Part 1: Test with compression

ISO 16938-2:2019 建筑和土木工程 - 用于接头中使用的密封剂测定多孔基材的染色 - 第2部分:无压缩试验

This document specifies a method for determining the staining of porous substrates (e.g. marble, limestone, sandstone, or granite) by sealants used in building construction. The method evaluates the likelihood of a sealant causing an early stain on a porous substrate due to exudation of materials from the sealant. The outcome of the test is specific to the tested sealant and tested substrate and cannot be extrapolated to other sealant formulations or other porous substrates. During this accelerated test, if the sealant does not stain or discolour the substrates, it does not mean that the tested sealant will not stain or discolour the tested porous substrate over a longer time period.

Buildings and civil engineering works — Determination of the staining of porous substrates by sealants used in joints — Part 2: Test without compression

ASTM C1809-19 绝缘蒸汽缓凝剂中压敏胶密封接头渗透性试验的试样制备和结果报告的标准实施规程

Standard Practice for Preparation of Specimens and Reporting of Results for Permeance Testing of Pressure Sensitive Adhesive Sealed Joints in Insulation Vapor Retarders

JC/T 550-2019 聚氯乙烯塑料地板胶粘剂

PVC plastic floor adhesive