91.100.50 粘合料、密封材料 标准查询与下载

JC/T 2536-2019 水泥-水玻璃灌浆材料

Cement-water glass grouting material

T/FSI 033-2019 建筑用高性能硅酮结构密封胶

本标准规定了建筑用高性能硅酮结构密封胶的分类和标记、要求、试验方法、检验规则、标志、包 装、运输和贮存。 本标准适用于高层（建筑高度大于27 m的住宅建筑和建筑高度大于24 m的非单层厂房、仓库和其 他民用建筑）、超高层（建筑高度大于100 m的民用建筑）建筑幕墙及其他结构粘接装配用高性能硅酮 结构密封胶。

High performance silicone structural sealant for construction

T/FSI 047-2019 建筑用硅烷改性聚醚密封胶

本标准规定了建筑用硅烷改性聚醚密封胶的术语和定义、分类、要求、试验方法、检验规则、标志、 包装、运输和贮存。 本标准适用于建筑接缝、干缩位移接缝和其它装饰装修用硅烷改性聚醚密封胶。

Silane modified polyether sealant for construction

ASTM D8265-19 在已安装的土工膜中绘制泄漏图的电气方法的标准实施规程

Standard Practices for Electrical Methods for Mapping Leaks in Installed Geomembranes

T/FSI 034-2019 建筑用高性能硅酮耐候密封胶

本标准规定了建筑用高性能硅酮耐候密封胶的术语、分类和标记、要求、试验方法、检验规则、标 志、包装、运输和贮存。 本标准适用于高层（建筑高度大于27 m的住宅建筑和建筑高度大于24 m的非单层厂房、仓库和其 他民用建筑）、超高层（建筑高度大于100 m的民用建筑）建筑幕墙及其他建筑接缝用高性能硅酮耐候 密封胶。 本标准不适用于建筑幕墙工程中结构性装配用密封胶。 

High-performance silicone weather-resistant sealant for construction

BS EN 1849-2:2019 用于防水的柔性片材 测定单位面积的厚度和质量 屋顶防水用塑料和橡胶板

What is BS EN 1849 ‑ 2 – Flexible sheets for waterproofing about?   BS EN 1849 is a series of European standards that discusses flexible sheets the determination of thickness and mass per unit area. The flexible sheets for waterproofing are water-resistant and fire-resistant.   BS EN 1849 ‑ 2 specifies methods for the determination of the thickness and mass per unit area of plastic and rubber sheets for roof waterproofing.   Who is BS EN 1849 ‑ 2 –

Flexible sheets for waterproofing. Determination of thickness and mass per unit area. Plastics and rubber sheets for roof waterproofing

ASTM D7636/D7636M-11(2019) 改性沥青屋顶系统取样和分析的标准实施规程

1.1 This practice is for removing specimens from existing modified bitumen roof membranes for visual assessment and evaluation for abnormalities in the membrane. The roof membrane consists of one or more plies/sheet materials in which at least one ply is a modified bitumen (MB) sheet, and which is installed with one or more of the following methods: hot asphalt, heat welding (open flame torching or heated air), cold adhesive, or self-adhesive. The roof membrane may consist of one or more plies of the following: 1.1.1 SBS (styrene-butadiene-styrene), APP (attactic polypropylene), or other polymer, modified bitumen sheet materials. 1.1.2 An exposed modified bitumen sheet material, that is, a modified cap sheet, covering multiple layers of built-up roofing (BUR) plies. 1.1.3 Any adhesive or bitumen component used to install the roof membrane. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Sampling and Analysis of Modified Bitumen Roof Systems

ASTM D8189-19 用动态剪切流变仪（DSR）测定沥青粘合剂和乳化沥青残渣粘性的标准试验方法

1.1 This test method covers the determination of pull-off force and pull-off work of asphalt binders and emulsified asphalt residue by means of pull-off testing. The tackiness test is conducted using the dynamic shear rheometer (DSR) at one or more temperatures. NOTE 1—This standard may be used for unconditioned material or material conditioned in accordance with Test Method D2872. The majority of development work on this test method was performed on unconditioned material. The emulsified asphalt residue should never be conditioned. 1.2 A precision and bias statement for this standard has not been developed at this time. Therefore, this standard should not be used for acceptance or rejection of a material for purchasing purposes. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Tackiness of Asphalt Binders and Emulsified Asphalt Residue Using the Dynamic Shear Rheometer (DSR)

ASTM D8231-19 探测和定位屋顶和防水膜裂缝的低压电子扫描系统的使用

1.1 This practice describes standard procedures for using an electronic scanning system to locate membrane breaches on both horizontal and vertical surfaces to locate potential leaks in exposed roofing and waterproofing membranes. 1.2 This practice addresses the need for a detailed technical description of a scanning method and procedures that are used to test and verify the integrity of membranes. 1.3 This practice is not intended to replace visual or other methods of inspection. It is to be used in conjunction with other methods of roof inspection when specified. 1.4 This practice requires that the detection and location equipment, procedures, and survey parameters used are calibrated to meet established minimum leak detection sensitivity. The detection sensitivity calibration must be verified on a regular basis using the manufacturer’s procedures to assure maximum confidence in the results. 1.5 Scanning surveys can be used on membranes installed on roofs, plaza decks, pools, water features, covered reservoirs, and other roofing and waterproofing applications. 1.6 This practice is applicable for membranes made of electrically insulating materials and is used on certain moderately conductive membranes (see Test Method D4496). 1.7 This practice provides a description of the scanning method and equipment for locating membrane breaches using electric conductance and is intended to be used in conjunction with the manufacturer’s instructions for the proper operation and use of the equipment. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for the Use of a Low Voltage Electronic Scanning System for Detecting and Locating Breaches in Roofing and Waterproofing Membranes

ASTM D3279-19 标准测试方法 n -Heptane Insoluble

1.1 This test method covers determination of the mass percent of asphaltenes as defined by insolubility in normalheptane solvent. It is applicable to all solid and semi-solid petroleum asphalts containing little or no mineral matter, to gas oils, to heavy fuel oils, and to crude petroleum that has been topped to a cut-point of 343 °C or higher. 1.2 The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard. 1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See Section 7 for a specific hazard statement. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for n-Heptane Insolubles

ASTM D2872-19 热和空气对沥青移动膜影响的标准试验方法（滚动薄膜烘箱试验）

Standard Test Method for Effect of Heat and Air on a Moving Film of Asphalt (Rolling Thin-Film Oven Test)

ASTM C1315-19 养护和密封混凝土用具有特殊性能的液膜形成化合物的标准规范

1.1 This specification provides requirements for membraneforming liquids suitable for use as curing compounds and sealers on freshly placed concrete and as sealers on hardened concrete. These membranes have special properties, such as, alkali resistance, acid resistance, adhesion-promoting qualities, and resistance to degradation by UV light. NOTE 1—For liquid membrane-forming curing compounds specified primarily by their ability to retain water in newly placed concrete (and by drying time, and for white pigmented products, reflectance), see Specification C309. 1.2 This is a performance specification. The allowable composition of products covered by this specification is limited by various local, regional, and national regulations. Issues related to air quality (solvent emission), worker exposure, and other hazards are not addressed here. It is the responsibility of the producers and users of these materials to comply with pertinent regulations. Warning—Some VOC exempt solvents used to meet the regulations are extremely flammable with low auto ignition temperatures and rapid evaporation rates. Consult the manufacturer’s product information sheet for important application and safety information. 1.3 The values stated in SI units are to be regarded as the standard. (Inch pound units are shown in parentheses). 1.4 The following precautionary caveat pertains only to the test methods portion, Section 9, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Liquid Membrane-Forming Compounds Having Special Properties for Curing and Sealing Concrete

ASTM D2041/D2041M-19 沥青混合物理论最大比重和密度的标准试验方法

1.1 This test method covers the determination of the theoretical maximum specific gravity and density of uncompacted asphalt mixtures at 25 °C [77 °F]. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.2.1 Residual pressure measurements are shown in both the SI unit of kPa and the commonly used nonstandard equivalent unit of “mm of Hg.” 1.2.2 Measurements of volume and mass are only given in SI units because they are the only units typically used in practice when performing this test method. 1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Theoretical Maximum Specific Gravity and Density of Asphalt Mixtures

ASTM C1135-19 测定结构密封胶拉伸粘合性能的标准试验方法

1.1 This test method covers a laboratory procedure for quantitatively measuring the tensile adhesion properties of structural sealants, hereinafter referred to as the “sealant”. 1.2 The values stated in SI (metric) units are to be regarded as the standard. The inch-pound values given in parentheses are provided for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—Two ISO standards are known that develop similar information to C1135; ISO 8339 and ISO 8340. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining Tensile Adhesion Properties of Structural Sealants

ASTM D1227/D1227M-13(2019)e1 用作屋顶保护涂层的乳化沥青的标准规范

1.1 This specification covers emulsified asphalt suitable for use as a protective coating for built-up roofs and other exposed surfaces with inclines of not less than 4 % or 42 mm/m [1⁄2 in./ft]. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Emulsified Asphalt Used as a Protective Coating for Roofing

ASTM D6496/D6496M-19 测定针刺土工合成材料粘土衬垫顶部和底部之间平均粘结剥离强度的标准试验方法

Standard Test Method for Determining Average Bonding Peel Strength Between Top and Bottom Layers of Needle-Punched Geosynthetic Clay Liners

ASTM C1253-14(2019) 测定密封剂衬垫放气潜力的标准试验方法

1.1 This test method provides a procedure for determining the outgassing potential of a sealant backing when it is punctured during or after installation, with the puncture occurring before the sealant cures. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining the Outgassing Potential of Sealant Backing

ASTM D5076/D5076M-13(2019) 测量屋顶和防水膜空隙的标准试验方法

1.1 This test method includes two procedures for measuring the area of voids in the adhesive between materials used in roofing and waterproofing systems. Both procedures require a count of the number of voids. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Measuring Voids in Roofing and Waterproofing Membranes

ASTM C864-05(2019) 致密弹性压缩密封垫圈、定位块和垫片的标准规范

1.1 This specification covers preformed dense elastomeric compression gaskets and accessories for use in sealing and glazing applications. These materials are generally used to seal or serve as components of compression sealing systems between mechanically restrained surfaces in building constructions. 1.2 Test Method C1166, as referenced in this specification, should be used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use. 1.3 The following precautionary statement pertains only to the test method portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Dense Elastomeric Compression Seal Gaskets, Setting Blocks, and Spacers

ASTM C681-14(2019) 油基和树脂基刀级通道玻璃化合物挥发性的标准试验方法

1.1 This test method describes the determination of the volatility of oiland resin-based, knife-grade, channel glazing compounds. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The subcommittee with jurisdiction is not aware of any similar ISO standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Volatility of Oil- and Resin-Based, Knife-Grade, Channel Glazing Compounds