91.100.50 粘合料、密封材料 标准查询与下载

ASTM C772-03(2019) 预成型胶带密封剂的油迁移或增塑剂渗出的标准试验方法

1.1 This test method covers a laboratory procedure that can be used to determine the oil migration or plasticizer bleed-out of preformed tape sealants. 1.2 The values stated in acceptable metric units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 The subcommittee with jurisdiction is not aware of any similar ISO standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Oil Migration or Plasticizer Bleed-Out of Preformed Tape Sealants

ASTM C879-03(2019) 预成型胶带密封剂用脱模纸的标准试验方法

1.1 These test methods cover laboratory procedures for evaluating the release characteristics of a release paper intended to be supplied in direct contact with a preformed tape sealant. 1.2 The values stated in metric (SI) units are to be regarded as the standard. The values given in parentheses are provided for information purposes only. 1.3 The subcommittee with jurisdiction is not aware of any similar ISO standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Release Papers Used with Preformed Tape Sealants

ASTM D2728-98(2019) 道路焦油的铺路用途和应用温度的标准实施规程

1.1 This practice covers the selection and application temperatures of road tar grades in the construction and maintenance of pavements. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Paving Uses and Application Temperatures for Road Tars

ASTM C864-05(2019) 致密弹性压缩密封垫圈、定位块和垫片的标准规范

1.1 This specification covers preformed dense elastomeric compression gaskets and accessories for use in sealing and glazing applications. These materials are generally used to seal or serve as components of compression sealing systems between mechanically restrained surfaces in building constructions. 1.2 Test Method C1166, as referenced in this specification, should be used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use. 1.3 The following precautionary statement pertains only to the test method portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Dense Elastomeric Compression Seal Gaskets, Setting Blocks, and Spacers

ASTM D6496/D6496M-19 测定针刺土工合成材料粘土衬垫顶部和底部之间平均粘结剥离强度的标准试验方法

Standard Test Method for Determining Average Bonding Peel Strength Between Top and Bottom Layers of Needle-Punched Geosynthetic Clay Liners

ASTM D2377-14(2019) 填缝化合物和密封剂的无粘性时间的标准试验方法

1.1 This test method describes the determination of the tack-free time property of caulking compounds and sealants. This test method is applicable to both gun and knife grades. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 The committee with jurisdiction over this standard is not aware of any comparable standard published by other organizations. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Tack-Free Time of Caulking Compounds and Sealants

ASTM D4932/D4932M-89(2019) 屋顶和防水板、屋面和瓦的紧固件断裂和抗撕裂性的标准试验方法

1.1 This test method covers the determination of the force needed to pull a fastener through any type of roofing or waterproofing ply sheet, roll roofing, or shingle, or to cause fastener failure under specified laboratory conditions. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Fastener Rupture and Tear Resistance of Roofing and Waterproofing Sheets, Roll Roofing, and Shingles

ASTM C771-14(2019) 预制密封带热老化后重量损失的标准试验方法

1.1 This test method covers a laboratory procedure for determining the weight loss after heat aging of preformed tape sealants. NOTE 1—Test Method C681 describes a weight loss or volatility test for knife-grade glazing compounds. 1.2 The values stated in acceptable metric units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 The subcommittee with jurisdiction is not aware of any similar ISO standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Weight Loss After Heat Aging of Preformed Tape Sealants

ASTM C681-14(2019) 油基和树脂基刀级通道玻璃化合物挥发性的标准试验方法

1.1 This test method describes the determination of the volatility of oiland resin-based, knife-grade, channel glazing compounds. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The subcommittee with jurisdiction is not aware of any similar ISO standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Volatility of Oil- and Resin-Based, Knife-Grade, Channel Glazing Compounds

ASTM C1258-19 绝缘用蒸汽缓凝剂耐高温和耐湿性的标准试验方法

Standard Test Method for Elevated Temperature and Humidity Resistance of Vapor Retarders for Insulation

ASTM C1878-19 绝热用蒸汽缓凝剂表面耐水性的标准试验方法

1.1 This test method details a procedure for the determination of the surface water resistance of a vapor retarder by measurement of the quantity of water absorbed in a specified time by the service-exposed surface of a vapor retarder intended for use on thermal insulation. 1.2 This test method covers vapor retarders that are expected to withstand intermittent or occasional exposure to liquid water on the exposed side. Examples of this exposure are condensation and light rain during installation before a structure is enclosed. 1.3 This method does not cover vapor retarders intended for exposure to the elements in outdoor applications. 1.4 This method does not cover thermal insulation products that also act as vapor retarders, such as elastomeric foam and cellular glass. 1.5 In the test, the specimen is exposed to a specified volume of water over a given exposure area, with a resultant head pressure. 1.6 The test method is based on Test Method D3285 (withdrawn), the so-called “Cobb” test used for paper. 1.7 The values stated in SI units are to be regarded as standard. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Surface Water Resistance of Vapor Retarders for Thermal Insulation

T/CECS 581-2019 建筑接缝密封胶应用技术规程

本规程共分7章和2个附录，主要技术内容包括：总则、术语和符号、基本规定、材料、接缝密封设计、施工及验收、维护。

Technical specification for application of construction joint sealant

ASTM D2726/D2726M-19 非吸收性压实沥青混合料的堆积比重和密度的标准试验方法

Standard Test Method for Bulk Specific Gravity and Density of Non-Absorptive Compacted Asphalt Mixtures

BS EN 13074-1:2019 沥青和沥青粘合剂 从沥青乳液或稀释或稀释的沥青粘合剂中回收粘合剂 蒸发回收

What is BS EN 13074-1 - Recovery of binder from bituminous emulsion by evaporation about?   BS EN 13074 is a series of the European standard on bitumen and bituminous binders that focusses on the recovery property of binders which plays an important role in the performance and service life of building structures.   BS EN 13074-1 is the first part of the BS EN 13074 series of documents that specifies a method for the recovery of binder from a bituminous emulsion or from a cut-back or fluxed bitumen after conditioning at ambient temperature for 24 h followed by 24 h at 50 °C, in such a way that will enable further testing with minimum changes of the binder characteristics.   NOTE: BS EN 13074-1

Bitumen and bituminous binders. Recovery of binder from bituminous emulsion or cut-back or fluxed bituminous binders. Recovery by evaporation

ASTM D2643/D2643M-08(2019) 用作运河和沟渠衬套的预制沥青土工膜的标准规范（露出型）

Standard Specification for Prefabricated Bituminous Geomembrane Used as Canal and Ditch Liner (Exposed Type)

T/ZBH 010-2019 中空玻璃用反应型热熔密封胶

本标准规定了中空玻璃用反应型热熔密封胶的术语和定义、分类和标记、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于非结构装配的中空玻璃边部密封用反应型热熔胶。

Reactive hotmelt sealants used insulating glass unit

ASTM C1369-19 结构上釉中空玻璃单元用二次封边材料的标准规范

1.1 This specification describes the properties of cold, liquid-applied, single or multi-component, chemically curing, elastomeric sealants used as the secondary seal of sealed insulating glass units, hereinafter referred to as the “sealant” (see Fig. 1). These sealants are intended to be a structural component of sealed insulating glass (IG) units used in structural sealant glazing (hereinafter referred to as SSG). Typical designs and considerations can be found in Guide C1249. Presently only certain silicone sealants are recognized as having the necessary durability for use as secondary sealant in IG units in SSG applications. 1.2 This specification does not describe all of the necessary properties of the sealant. Only those properties for which there are ASTM test methods and industry-agreed-upon minimum acceptable test requirements are described by this specification. Additional properties will be added as ASTM test methods for these properties become available. 1.3 This specification only addresses the durability of the secondary edge sealants for structurally glazed insulating glass units. Durability of sealed insulating glass units can be found in specifications and guides that reside within ASTM Committee E06. 1.4 The committee with jurisdiction for this standard is not aware of any comparable standard published by other organizations. 1.5 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information purposes only. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Secondary Edge Sealants for Structurally Glazed Insulating Glass Units

ASTM D2962-10(2019) 煤沥青体积温度校正计算的标准实施规程

1.1 This practice covers calculation of the amount of expansion or contraction of a volume of liquid coal-tar pitch due to a change of temperature. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Calculating Volume-Temperature Correction For Coal-Tar Pitches

ASTM C1021-08(2019) 从事建筑密封胶试验的实验室的标准实施规程

1.1 This practice describes the qualifications, including minimum requirements for personnel and equipment, duties, responsibilities, and services of independent commercial materials testing laboratories engaged in the testing of caulking and sealants used in building construction. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3 The subcommittee with jurisdiction of this standard is not aware of any similar or equivalent ISO standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Laboratories Engaged in Testing of Building Sealants

ASTM D2202-00(2019) 密封剂坍落度的标准试验方法

1.1 This test method covers a laboratory procedure for the determination of the degree of slump of a sealant when used in a vertical joint in a structure. 1.2 The values stated in either inch-pound or SI (metric) units are to be separately regarded as the standard. Within the text, the inch-pound units are shown in parentheses. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—A related ISO standard is ISO 7390. The user should compare to determine how it differs from this test method. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Slump of Sealants