91.100.50 粘合料、密封材料 标准查询与下载

ASTM C1369-19 结构上釉中空玻璃单元用二次封边材料的标准规范

1.1 This specification describes the properties of cold, liquid-applied, single or multi-component, chemically curing, elastomeric sealants used as the secondary seal of sealed insulating glass units, hereinafter referred to as the “sealant” (see Fig. 1). These sealants are intended to be a structural component of sealed insulating glass (IG) units used in structural sealant glazing (hereinafter referred to as SSG). Typical designs and considerations can be found in Guide C1249. Presently only certain silicone sealants are recognized as having the necessary durability for use as secondary sealant in IG units in SSG applications. 1.2 This specification does not describe all of the necessary properties of the sealant. Only those properties for which there are ASTM test methods and industry-agreed-upon minimum acceptable test requirements are described by this specification. Additional properties will be added as ASTM test methods for these properties become available. 1.3 This specification only addresses the durability of the secondary edge sealants for structurally glazed insulating glass units. Durability of sealed insulating glass units can be found in specifications and guides that reside within ASTM Committee E06. 1.4 The committee with jurisdiction for this standard is not aware of any comparable standard published by other organizations. 1.5 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information purposes only. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Secondary Edge Sealants for Structurally Glazed Insulating Glass Units

ASTM D2962-10(2019) 煤沥青体积温度校正计算的标准实施规程

1.1 This practice covers calculation of the amount of expansion or contraction of a volume of liquid coal-tar pitch due to a change of temperature. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Calculating Volume-Temperature Correction For Coal-Tar Pitches

ASTM D3161/D3161M-19 陡坡屋顶产品防风标准试验方法（风扇诱导法）

Standard Test Method for Wind-Resistance of Steep Slope Roofing Products (Fan-Induced Method)

ASTM D4073/D4073M-06(2019)e1 沥青屋面薄膜拉伸撕裂强度的标准试验方法

1.1 This test method covers the determination of the tensiletear strength of bituminous roofing membranes. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Tensile-Tear Strength of Bituminous Roofing Membranes

ASTM C1021-08(2019) 从事建筑密封胶试验的实验室的标准实施规程

1.1 This practice describes the qualifications, including minimum requirements for personnel and equipment, duties, responsibilities, and services of independent commercial materials testing laboratories engaged in the testing of caulking and sealants used in building construction. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3 The subcommittee with jurisdiction of this standard is not aware of any similar or equivalent ISO standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Laboratories Engaged in Testing of Building Sealants

ASTM D2829/D2829M-07(2019)e1 现有建筑屋顶系统采样和分析的标准实践

1.1 This practice is a guide for removing test specimens from existing built-up roofing systems in the field and for determining the approximate quantities of the components of that specimen (Note 1). Components determined may be: 1.1.1 Insulation components when they are part of the roof membrane system, 1.1.2 Plies of roofing felt, 1.1.3 Interply layers of bituminous material, 1.1.4 Top coating, and 1.1.5 Surfacing. NOTE 1—This procedure is for the investigation of existing roofs and is not intended for new construction inspection. 1.2 This practice is applicable to both 914-mm [36-in.] and 1000-mm [39 3⁄8-in.] wide felt rolls. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary information, see 6.3.2.1. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Sampling and Analysis of Existing Built-Up Roof Systems

ASTM C719-14(2019) 循环运动下弹性接缝密封剂的粘附力和内聚力的标准试验方法（霍克曼循环）

Standard Test Method for Adhesion and Cohesion of Elastomeric Joint Sealants Under Cyclic Movement (Hockman Cycle)

ASTM D2202-00(2019) 密封剂坍落度的标准试验方法

1.1 This test method covers a laboratory procedure for the determination of the degree of slump of a sealant when used in a vertical joint in a structure. 1.2 The values stated in either inch-pound or SI (metric) units are to be separately regarded as the standard. Within the text, the inch-pound units are shown in parentheses. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—A related ISO standard is ISO 7390. The user should compare to determine how it differs from this test method. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Slump of Sealants

ASTM C919-19 声学应用中密封剂的使用

1.1 This practice provides information for the use of sealants to reduce sound transmission characteristics of interior walls, ceilings, and floors by proper application of sealants to joints, voids, and penetrations normally found in building construction, which are commonly referred to as “flanking paths.” 1.2 The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations. 1.3 This standard does not purport to address fire stopping or safing requirements for joints, voids, and penetrations through fire-rated wall, ceiling, and floor assemblies. Additional requirements may be necessary for fire-rated assemblies to meet the applicable building code provisions. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Use of Sealants in Acoustical Applications

ASTM D3462/D3462M-19 用玻璃毡和矿物颗粒制成的沥青瓦的标准规范

1.1 This specification covers asphalt roofing in shingle form, composed of glass felt or felts impregnated and coated on both sides with asphalt, and surfaced on the weather side with mineral granules. This specification is designed for the evaluation of products as manufactured. The test methods, physical requirements, and minimum masses are to be measured immediately after packaging or at a reasonable time, as agreed upon between buyer and seller, after manufacture and before installation. Physical and performance requirements after application and during in-service use of the products described herein are beyond the scope of this material specification. 1.2 Shingles meeting this specification are intended to be applied with a headlap of not less than 51 mm [2 in.]. 1.3 The shingles shall be supplied with a factory-applied self-sealing adhesive or be designed to be locked together during installation of the shingles. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 The following safety hazards caveat pertains only to the test method described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Asphalt Shingles Made from Glass Felt and Surfaced with Mineral Granules

ASTM D2171/D2171M-18 用真空毛细管粘度计测定沥青粘度的标准试验方法

Standard Test Method for Viscosity of Asphalts by Vacuum Capillary Viscometer

ASTM D2170/D2170M-18 沥青运动粘度的标准试验方法

Standard Test Method for Kinematic Viscosity of Asphalts

ASTM D3549/D3549M-18 压实沥青混合料试样厚度或高度的标准试验方法

1.1 This test method covers determination of the thickness (or height) of compacted asphalt mixture specimens. 1.2 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.2.1 Section 7.4 specifies SI units because they are the units used in the equations for Test Methods D1188 and D2726. Performing calculations without first converting any measurements made in inch-pound units to SI units in 7.4 will result in nonconformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Thickness or Height of Compacted Asphalt Mixture Specimens

T/ZJBMQA 003-2018 绝热工程用密封胶

本标准规定了绝热工程用密封胶的术语和定义、一般要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存。本标准适用于在绝热材料间起粘结及密封作用的密封胶。 表1　性能指标 项目　单位　性能指标 密度　kg/m3　1300±100 固含量　%　≥80 拉伸粘结强度　MPa　≥0.03 剪切强度　MPa　≥0.08                                                             伸长率　%　≥80 耐热性　/　在65℃环境中放置168h，外观无异常。 耐低温性　/　在–196℃环境中放置2h，无开裂、无脱落。 体积变化率　%　≤22

Sealant for insulation engineering

T/ZJBMQA 004-2018 绝热工程用玛蹄脂

本标准规定了绝热工程用玛蹄脂的术语和定义、分类和标记、一般要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存。本标准适用于敷设在绝热工程材料外表，起防潮、保护作用的玛蹄脂 表1　性能指标 项目　单位　性能指标 　　Ι　Ⅱ 密度　kg/m3　1500±100 干燥时间　表干时间　h　≤6 　实干时间　h　≤168 固含量　%　≥80 不透水性　/　0.1MPa,不透水 氧指数　%　≥26.0                   　≥30.0 自熄性　s　＜3　＜1 透湿系数　 ng/(Pa?s?m)　≤0.005 耐低温性　/　–40℃下放置24h，不开裂、脱落。 耐热性　/　在95℃温度下45o斜搁5h，温度上升至120℃时45o斜搁1h，无流淌及起泡现象。

Mastic for insulation engineering

ASTM D4616-95(2018) 用反射光进行显微镜分析和沥青中间相测定的标准试验方法

1.1 This test method covers laboratory procedures for the preparation of granular and melted samples for microscopic analysis using reflected light to identify and estimate the amount and size of the mesophase. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Microscopical Analysis by Reflected Light and Determination of Mesophase in a Pitch

ASTM D7694/D7694M-18 自粘改性沥青薄板材料的标准试验方法

1.1 These test methods cover test procedures for prefabricated, reinforced, self-adhesive (SA) polymer-modified bituminous sheet materials designed for singleor multiple-ply application in roofing and waterproofing membranes. 1.2 These test methods specifically address the selfadhesive characteristics of modified bituminous sheet materials, and are intended as a supplement to those found in Test Methods D5147/D5147M. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.4 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Self-Adhesive Modified Bituminous Sheet Material

T/SHHJ 000018-2018 装配式建筑外墙用密封胶

本标准规定了装配式建筑外墙用密封胶的术语和定义、分类和标记、要求、试验方法、检验规则、标志、包装、运输和贮存。

Sealants for Prefabricated Building Exterior Wall

ASTM D70-18a 半固体沥青粘结剂密度的标准测试方法（比重瓶法）

Standard Test Method for Density of Semi-Solid Asphalt Binder (Pycnometer Method)

ASTM D4296-18 沥青取样的标准实施规程

1.1 This practice covers procedures for sampling pitch at points of manufacture, storage, and delivery. 1.2 The values stated in SI units are to be regarded as standard. The values in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific warning statements are given in Section 11. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Sampling Pitch