91.100.50 粘合料、密封材料 标准查询与下载

ASTM D3461-18 沥青和沥青软化点的标准试验方法（梅特勒杯球法）

1.1 This test method covers the determination of the softening point of asphalt and pitch in the range from 50 °C to 180 °C by the cup-and-ball apparatus, and gives results comparable to those obtained by Test Method D36. NOTE 1—If the softening point of asphalt by this Mettler cup-and-ball method fails to meet specified requirements, tests may be rerun using the Test Method D36 (ring-and-ball) softening point apparatus as a referee method. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Softening Point of Asphalt and Pitch (Mettler Cup-and-Ball Method)

T/SDDA 0001-2018 玻 化 砖 背 胶

1  范围 2  规范性引用文件 3  术语和定义   3.1  玻化砖   3.2  玻化砖背胶 4  一般要求 5  要求 6  试验方法   6.1  标准试验条件   6.2  试验基材和仪器设备        6.2.1  试验基材        6.2.2  钢制垫板        6.2.3  试验仪器   6.3  玻化砖背胶搅拌   6.4  容器中状态   6.5  施工性   6.6  拉伸粘结强度        6.6.1  试件制备             6.6.1.1  试件成型框             6.6.1.2  试件成型        6.6.2  标准养护后拉伸粘结强度 6.6.3  浸水后拉伸粘结强度 6.6.4  热老化后拉伸粘结强度 6.6.5  冻融循环后拉伸粘结强度 6.6.6  拉伸粘结强度试验结果评定与表示 7  检验规则   7.1  检验分类        7.1.1  出厂检验        7.1.2  型式检验   7.2  组批   7.3  抽样   7.4  判定规则 8  标志 9  包装、运输和贮存   9.1  包装   9.2  运输和贮存

vitrified tile adhesive

ASTM D1670/D1670M-11(2018) 沥青材料加速和户外风化破坏终点的标准试验方法

1.1 This test method covers the use of a spark generating apparatus for determination of failure due to cracking of bituminous materials undergoing accelerated or outdoor weathering on electrically conductive backings. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Failure End Point in Accelerated and Outdoor Weathering of Bituminous Materials

BS EN 17190:2018 用于防水的柔性片材 太阳反射率

What is BS EN 17190 - Flexible sheets for waterproofing – Solar Reflectance Index about?   BS EN 17190 is the European standard that discusses the solar reflectance index for flexible sheets for waterproofing.    BS EN 17190 gives a calculation method of the Solar Reflectance Index (SRI) and the determination of solar reflectivity and thermal emissivity for waterproofing flexible sheets for roofs with a slope smaller than 10°.   Who is BS EN 17190 - Flexible sheets for waterproofing – Solar Reflectance Index for?   BS EN 17190 on solar reflectance of flexible sheets for waterproofing in useful for:   Manufacturers of flexible sheets

Flexible sheets for waterproofing. Solar Reflectance Index

ASTM D3320/D3320M-18 乳化煤沥青（矿物胶体型）的标准规范

1.1 This specification covers mineral-colloid-stabilized, emulsified coal-tar pitch suitable for use as a weatherprotective and aliphatic-solvent resistant coating over bituminous pavements of airports, parking areas, and driveways. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 The following precautionary caveat pertains only to the test method portion, Section 6, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Emulsified Coal-Tar Pitch (Mineral Colloid Type)

ASTM D5167-13(2018) 评定用热涂接缝和裂缝密封剂及填料熔化的标准实施规程

1.1 This practice establishes the procedure for melting or heating, or both, of hot-applied joint and crack sealants and fillers in preparation for the making of test specimens used in the laboratory evaluations of the sealants and fillers. Refer to the specific standard material specification for sampling requirements, test sample quantity, temperatures and times for melting and heating, and the number of specimens required for testing. 1.2 This practice is applicable to the hot-applied joint and crack sealants and fillers used in both portland cement and asphaltic-concrete pavements. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4 Warning—Mercury has been designated by the EPA and many state agencies as a hazardous material that can cause central nervous system, kidney, and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury-containing products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPA’s website—http://www.epa.gov/mercury/faq.htm—for additional information. Users should be aware that selling mercury and/or mercury-containing products into your state may be prohibited by state law. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautions, see Section 7. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Melting of Hot-Applied Joint and Crack Sealant and Filler for Evaluation

ASTM C1330-18 用于冷液体应用密封剂的圆柱形密封胶背衬的标准规范

1.1 This specification covers the basic requirements for cylindrical sealant backing to be used with cold liquid applied sealants for use in building seals. 1.2 Cylindrical sealant backing serves one or more of the following functions: 1.2.1 Limits the amount and depth of sealant applied into a joint, 1.2.2 Acts as a bond breaker to allow joint movement without undue stress to the sealant, 1.2.3 Provides a form to assist the sealant in developing the proper shape factor, and 1.2.4 Acts as a barrier to the flow of sealant through the joint. 1.3 The committee with jurisdiction over this standard is not aware of any comparable standards published by other ASTM committees or other organizations. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Cylindrical Sealant Backing for Use with Cold Liquid-Applied Sealants

ASTM C1536-18 用于测量气溶胶泡沫密封胶的产量的标准测试方法

Standard Test Method for Measuring the Yield for Aerosol Foam Sealants

DB35/T 516-2018 益胶泥通用技术条件

本标准规定了益胶泥的术语和定义、产品分类、技术要求、试验方法、检验规则、标志、包装、运输和贮存等。 本标准适用于以益胶泥作为部分或全部产品名称的所有益胶泥。该产品适用于工业与民用建筑中工程防水以及有防水抗渗要求的陶瓷砖及饰面石板材粘结。

General Technical Conditions of Yijiao Clay

ASTM D227/D227M-03(2018) 屋顶和防水用煤焦油饱和有机毡的标准规范

1.1 This specification covers coal-tar-saturated organic felt intended to be used with coal-tar pitches conforming to the appropriate requirements of Specification D450/D450M in the construction of built-up roofs and in the construction of waterproofing systems. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Coal-Tar-Saturated Organic Felt Used in Roofing and Waterproofing

ASTM D6857/D6857M-18 使用自动真空密封法测定沥青混合料的最大比重和密度的标准试验方法

1.1 This test method covers the determination of maximum specific gravity and density of uncompacted asphalt mixtures at 25 °C [77 °F]. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Maximum Specific Gravity and Density of Asphalt Mixtures Using Automatic Vacuum Sealing Method

ASTM D6152/D6152M-12(2018) 用于屋顶的SEBS改性拖把沥青的标准规范

1.1 This specification covers SEBS (styrene-ethylenebutylene-styrene)-modified asphalt intended for use in built-up roof construction, construction of some modified bitumen systems, construction of bituminous vapor retarder systems, and for adhering insulation boards used in various types of roof systems. 1.2 This specification is intended as a material specification. Issues regarding the suitability of specific roof constructions or application techniques are beyond its scope. 1.3 The specified tests and property values used to characterize SEBS-modified asphalt are intended to establish minimum properties. In place system design criteria or performance attributes are factors beyond the scope of this specification. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for SEBS-Modified Mopping Asphalt Used in Roofing

DIN EN 13589:2018 沥青和沥青粘合剂. 用力延展性法测定改良沥青的抗拉性能; 德文版本EN 13589-2018

This European Standard specifies a method for determining the tensile properties of a bituminous binder, in particular those of polymer-modified bitumens by means of a force ductility test. The work done during the force ductility test is a criterion for assessing the quality of these materials.

Bitumen and bituminous binders - Determination of the tensile properties of modified bitumen by the force ductility method; German version EN 13589:2018

BS ISO 11527:2018 建筑物和土木工程 密封剂 测定拉丝性的试验方法

Buildings and civil engineering works. Sealants. Test method for the determination of stringiness

ASTM D6638-18 测定土工合成钢筋和节段混凝土单元（模块混凝土块）之间连接强度的标准试验方法

1.1 This test method is used to determine the connection properties between a layer of geosynthetic reinforcement and segmental concrete block units used in construction of reinforced soil retaining walls. The test is carried out under conditions determined by the user that reproduce the connection system at full scale. The results of a series of tests are used to define a relationship between connection strength for a segmental unit-geosynthetic connection system and normal load. 1.2 This is a performance test used to determine properties for design of retaining wall systems utilizing segmental concrete units and soil reinforcing geosynthetics, either geotextiles or geogrids. The test is performed on a full-scale construction of the connection and may be run in a laboratory or the field. 1.3 The values stated in SI units are regarded as the standard. The values stated in inch-pound units are provided for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining Connection Strength Between Geosynthetic Reinforcement and Segmental Concrete Units (Modular Concrete Blocks)

BS ISO 13640:2018 建筑物和土木工程 密封剂 测试基材规格

Buildings and civil engineering works. Sealants. Specifications for test substrates

ASTM D173/D173M-03(2018) 屋面和防水用沥青饱和棉织物的标准规范

1.1 This specification covers woven cotton fabrics saturated with either asphalt or coal-tar pitch intended to be used with asphalts conforming to Specifications D312/D312M or D449/ D449M, coal-tar pitches conforming to Specification D450/ D450M, or appropriate solvent bearing bituminous materials in the construction of roofing and waterproofing systems. 1.1.1 Asphalt-saturated cotton fabric shall be used with asphalt base plying cement; typical ones are mopping asphalts conforming to Specifications D312/D312M or D449/D449M or appropriate solvent bearing asphaltic compounds. 1.1.2 Coal-tar-saturated cotton fabric shall be used with coal-tar based plying cements; a typical one is coal-tar pitch conforming to Specification D450/D450M or appropriate solvent bearing coal-tar compounds. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Bitumen-Saturated Cotton Fabrics Used in Roofing and Waterproofing

ASTM C919-18 声学应用中密封剂的使用

Standard Practice for Use of Sealants in Acoustical Applications

ASTM D5147/D5147M-18 改性沥青片材取样和试验的标准试验方法

1.1 These test methods cover procedures for sampling and testing prefabricated, reinforced, polymer-modified bituminous sheet materials designed for singleor multiple-ply application in roofing and waterproofing membranes. These products may use various surfacing materials on one side. 1.2 These test methods cover a number of different products. Not all tests are required for every product. Only those called out in the Product Standard are required. 1.3 These test methods appear in the following order: Section Sampling 4 Conditioning 5 Thickness 6 Load Strain Properties 7 Tear Strength 8 Moisture Content 9 Water Absorption 10 Dimensional Stability 11 Low-Temperature Flexibility 12 Heat Conditioning 13 Accelerated Weathering 14 Granule Embedment 15 Compound Stability 16 Coating Thickness 17 Low Temperature Unrolling 18 Precision and Bias 19 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Sampling and Testing Modified Bituminous Sheet Material

ASTM D8125-18 再精炼发动机油底（REOB）/真空塔沥青填充剂（VTAE）的标准规范

1.1 This specification covers re-refined engine oil bottoms, also known as vacuum tower asphalt extender, that may be used in formulating asphalt for pavement construction and roofing. This specification has been developed specifically for these two categories of product and is not intended for other uses. Table 1 is to be used for pavement construction and Table 2 for roofing. “Re-refined engine oil bottoms” (REOB) is the prevailing name used by many state highway agencies and FHWA, while “vacuum tower asphalt extender” (VTAE) is the preferred name used by the manufacturers of the product. Since each name provides an important descriptor of production elements (“re-refined” and “vacuum tower”) for the specific product this specification addresses, this specification uses the term “REOB/VTAE.” 1.2 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Re-Refined Engine Oil Bottoms (REOB)/Vacuum Tower Asphalt Extender (VTAE)