91.120.99 有关建筑物防护的其他标准 标准查询与下载

T/CECS 466-2017 泡沫玻璃保温防水紧密型系统应用技术规程

总则、术语、基本规定、材料、设计、施工、质量验收

Technical specification for application of thermal insulation & waterproofing compact system based on cellular glass

T/CECS 467-2017 网织增强岩棉板薄抹灰外墙外保温工程技术规程

总则、术语、基本规定、材料、设计、施工、质量验收

Technical specification for external thermal insulation composite systems based on mesh-stitched enhanced rock wool board

ASTM C1483/C1483M-17 建筑物室外太阳辐射控制敷层的标准规格

1.1 The purpose of this specification is to provide general requirements for products used to reduce solar gains on buildings by reflecting solar radiation from roofs and walls. Radiation Control Coating (RCC) is a liquid applied material that cures to form a solid coating having a solar reflectance of at least 0.8 and an ambient temperature infrared emittance of at least 0.8. 1.2 This specification covers the physical and mechanical properties of liquid-applied RCCs designed for exterior application for buildings. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems has the potential to result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Exterior Solar Radiation Control Coatings on Buildings

ASTM C653-17 低密度毯型矿物纤维绝缘耐热性测定的标准指南

4.1 This guide provides a method to determine the thermal performance of low-density blanket-type insulation. It may be used for the purposes of quality assurance, certification, or research. 4.2 The thermal resistance of low-density insulation depends significantly on the density, the thickness, and thermal conductivity. Typical low-density, mineral-fiber insulation for buildings may vary in density from one specimen to the next. 4.3 Thermal tests are time-consuming in comparison with density and thickness measurements. Low-density insulation material is produced in large quantities. A typical lot would be a truckload or the amount necessary to insulate a house. 4.4 The relatively low unit cost of this product and the relatively high cost of thermal resistance testing makes it cost-effective to test only a small percentage of the product area. It is recommended that there be a determination of the density that is representative of a lot by the measurement of the average density of a statistically representative sampling. 4.5 A fewer number of thermal measurements are then made to determine the apparent thermal conductivity at the previously determined representative density. The essential significance of this guide is that a large lot of variable material is best characterized by: (a) determining the representative density, and by (b) determining the thermal property at this representative density with a small number of thermal measurements. 4.6 Building insulation products are commonly manufactured in thicknesses ranging from 19 to 330 mm (0.75 to 13 in.) inclusive. Experimental work has verified that there is a dependence of λapp on thickness for some low density materials. 4.7 The upper limit of test thickness for specimens evaluated using Test Methods C177, C518, and C1114 is established based upon the apparatus design, overall dimensions, expected thermal resistivity level and desired target accuracy. The testing organization is responsible for applying these restrictions when evaluating a product to ensure that the results meet applicable product labels and any existing regulatory requirements (2). 4.8 Extrapolation of the apparent thermal conductivity or the thermal resistance beyond the ranges of thickness or density of products tested is not valid. 1.1 This guide describes the calculation and interpolation of a thermal resistance value for low-density blanket-type insulation material at a particular density and thickness having been selected as representative of the product. It requires measured values of this average density and thickness, as well as apparent thermal conductivity value......

Standard Guide for Determination of the Thermal Resistance of Low-Density Blanket-Type Mineral Fiber Insulation

DB37/T 5033-2015 彩色防滑涂层施工技术规程（丙烯酸类）

本规程适用于在水泥或沥青路面上，以丙烯酸类涂料为基料，并采用涂敷工艺施工的彩色防滑涂层工程。不适用于在透水路面上施工。

Technical specification for construction of colored anti-skid coating (acrylic)

DB52/T 990-2015 茯苓白蚁防治技术规范

Poria cocos termite control technical specification

GOST R 56687-2015 混凝土和钢筋混凝土结构的防腐蚀保护. 混凝土抗硫酸盐侵蚀试验方法

Protection of concrete and reinforced-concrete construction from corrosion. Test method of sulfate resistance of concrete

GOST 25609-2015 楼面覆层用软砖体材料. 热吸收的测定规程

Soft and tile materials for floor covering. Procedure for determining the heat absorption

DB34/T 2182-2014 水利工程白蚁防治技术规程

本标准规定了水利工程白蚁防治的术语和定义、总则、白蚁防治设计、检查、预防、灭治、施工、验收、回访复查、药物和器械管理、档案管理、附录等内容。 本标准适用于安徽省境内水利工程白蚁防治，水土保持林木、苗圃的白蚁防治可参照执行。

Technical regulations for termite control in water conservancy projects

BS PAS 1188-2:2014 防洪产品.规范.第2部分:临时产品

Flood protection products. Specification. Temporary products

BS PAS 1188-4:2014 防洪产品.规范.可卸产品

Flood protection products. Specification. Demountable products

BS PAS 1188-3:2014 防洪产品. 规格. 建筑裙和墙密封系统

Flood protection products. Specification. Building skirt and wall sealant systems

BS PAS 1188-1:2014 防洪产品.规范.建筑孔径产品

Flood protection products. Specification. Building aperture products

GOST 28574-2014 施工中的腐蚀保护. 混凝土和钢筋混凝土结构. 保护覆盖层附着力的试验方法

Corrosion protection in construction. Concrete and reinforced concrete constructions. Methods of testing the protection covers adhesion

GOST 28575-2014 施工中的腐蚀保护. 混凝土和钢筋混凝土结构. 结构混凝土. 保护覆盖层的蒸汽渗透性试验

Corrosion protection in construction. Concrete and reinforced concrete constructions. Structural concrete. Test of vapor permeability of protection covers

BS PAS 64:2013 水损坏建筑物的缓解和恢复. 实施规程

Mitigation and recovery of water damaged buildings. Code of practice

DIN 4123:2013 现有建筑物范围内的挖掘,地基和支柱工程

Excavations, foundations and underpinnings in the area of existing buildings

ANSI/ASTM F2922:2013 聚乙烯(PE)波纹内壁雨水收集池规格

Specification for Polyethylene (PE) Corrugated Wall Stormwater Collection Chambers

ANSI/AARST CCAH-2013 减少1族和2族住房和联体别墅新型建筑中的氡

Reducing Radon in New Construction of 1 & 2 Family Dwellings and Townhouses

GOST 32494-2013 建筑物和构筑物. 保护构筑物用温度和湿度的数学模拟方法

Buildings and constructions. The method of mathematic simulation for temperature and humidity of protecting constructions