91.140.50 供电系统 标准查询与下载

CSA C282 Journal-2005 建筑物应急供电：维护日志

Alimentation électrique de secours des bâtiments : journal d?entretien

CAN/CSA-C282-2005 建筑物应急供电

1 Domaine d'application 1.1 Cette norme s'applique à la conception, à l'installation, au fonctionnement, à l'entretien et à la mise à l'essai de l'appareillage dont le rôle est d'assurer l'alimentation électrique dans des bâtiments ou des installations en cas de panne de l'alimentation normale, lorsqu'une alimentation électrique de secours est exigée dans le Code national du bâtiment du Canada (CNB). Notes: 1) Pour les lignes directrices concernant l'alimentation électrique de secours pour l'équipement de survie, voir l'annexe A. 2) Dans cette norme, le terme «bâtiment» désigne aussi les installations. 1.2 Cette norme ne porte pas sur ce qui suit: a) l'alimentation électrique de secours fournie par des accumulateurs ou d'autres sources d'alimentation ininterruptible; b) l'utilisation de l'alimentation électrique de secours; et c) la conception et la construction des appareils autonomes d'éclairage de secours conformes à la CSA C22.2 nº 141. 1.3 Dans les normes CSA, le terme «doit» indique une exigence, c'est-à-dire une prescription que l'utilisateur doit respecter pour assurer la conformité à la norme; «devrait» indique une recommandation ou ce qu'il est conseillé mais non obligatoire de faire et «peut», une possibilité ou un conseil. Les notes qui accompagnent les articles ne comprennent pas de prescriptions ni de recommandations. Elles servent à séparer du texte les explications ou les renseignements qui ne font pas proprement partie de la norme. Les notes au bas des figures et des tableaux font partie de ceux-ci et peuvent être rédigées comme des prescriptions. Les annexes peuvent être normatives (obligatoires) ou informatives (non obligatoires).

Emergency power supply for buildings

IEC 60364-1:2005 低压电气设施.第1部分:基本原则、一般特性评价和定义

1 This part of IEC 60364 applies to electrical installations such as those of: a) residential premises; b) commercial premises; c) public premises; d) industrial premises; e) agricultural and horticultural premises; f) prefabricated buildings; g) caravans, caravan sites and similar sites; h) construction sites, exhibitions, fairs and other temporary installations; i) marinas and pleasure craft. 2 It covers: a) circuits supplied at nominal voltages up to and including 1000 V a.c. or 1500 V d.c.; For a.c., the preferred frequencies which are taken into account in this standard are 50 Hz, 60 Hz and 400 Hz. The use of other frequencies for special purposes is not excluded. b) circuits, other than the internal wiring of apparatus, operating at voltages exceeding 1000 V and derived from an installation having a voltage not exceeding 1000 V a.c., e.g. discharge lighting, electrostatic precipitators; c) any wiring systems and cables not specifically covered by the standards for appliances; d) all consumer installations external to buildings; e) fixed wiring for telecommunications, signalling, control and the like (excluding internal wiring of apparatus); f) the extension or alteration of the installation and also parts of the existing installation affected by the extension or alteration. 3 The standard does not apply to a) electric traction equipment; b) electrical equipment of motor vehicles; c) electrical installations on board ships; d) electrical installations in aircraft; e) public street-lightning installations; f) installations in mines;

Low-voltage electrical installations - Part 1: Fundamental principles, assessment of general characteristics, definitions

DIN VDE 0100-718:2005 低压装置的安装.特殊装置或位置要求.第718部分:人员聚会用装置

Erection of low-voltage installations - Requirements for special installations or locations - Part 718: Installations for gathering of people

IEC 60364-7-706:2005 低压电气设施.第7-706部分:特殊设施或场所的要求.受限活动的导电场所

The particular requirements of this section apply to installations for restrictive conducting locations and to the supply to apparatus within these locations. A restrictive conducting location is one comprised mainly of metallic or conductive surrounding parts, within which it is likely that a person will come in contact through a substantial portion of his body with the conductive surrounding parts and where the possibility of interrupting this contact is limited.

Low-voltage electrical installations - Part 7-706: Requirements for special installations or locations - Conducting locations with restricted movement

JIS C 0364-7-740:2005 建筑物的电气设施.第7-740部分:特殊设施或位置的要求.博览会场、公共游乐场和圆形广场的房屋、娱乐装置和公用电话亭用临时电气设施

この規格は，移動形，仮設又は常設の電気機械及び電気機器を含む建造物の安全な設計，工事並びに運転に資するために最低限の電気設備要求事項について規定する。機械及び建造物は，催し物会場，遊園地，広場又はその他の場所で，臨時又は恒久的に，安全を損なうことなく，繰り返し施設されることを意図している。JIS C 0364の規格群におけるこの規格の目的は，娯楽装置に部分として組み込まれるか又は娯楽装置全体を構成するかにかかわらず，このような建造物及び機械に対する電気設備要求事項を明確にすることにあろ。この部は，非電気的事項にっいてぱ適用しない。また.機械の電気装置(JIS B 9960-1を参照)には適用しない。

Electrical installations of buildings -- Part 7-740: Requirements for special installations or locations -- Temporary electrical installations for structures, amusement devices and booths at fairgrounds, amusement parks and circuses

CSA C22.2 No.107.3-2005(R2010) 不间断电源系统

1.1 Scope Replace this clause of the RD with the following: 1.1.1 Equipment covered by this Standard This Standard applies to UNINTERRUPTIBLE POWER SYSTEMS (UPS). The primary function of the UPS for this Standard is to ensure continuity of an alternating power source. The UNINTERRUPTIBLE POWER SYSTEM may also serve to improve the quality of the power source by keeping it within specified characteristics. This Standard is applicable to movable, stationary, fixed, and built-in UPS for distribution systems up to 600 V a.c. This equipment is designed to be installed in accordance with the Canadian Electrical Code, Part I, CSA C22.1, or the National Electrical Code, ANSI/NFPA 70, and, unless otherwise identified, the Standard for the Protection of Electronic Computer Data-Processing Equipment, ANSI/NFPA 75. This Standard specifies requirements intended to ensure safety for the OPERATOR and, where specifically stated, for SERVICE PERSONNEL. This Standard is intended to reduce the risk of fire, electric shock, or injury to persons from installed equipment, both as a single unit or as a system of interconnected units, subject to installing, operating, and maintaining the equipment in the manner prescribed by the manufacturer. 1.1.2 Additional requirements In addition to the requirements in this Standard, a UPS is to comply with the UPS-relevant requirements of CAN/CSA-C22.2 No. 60950-1/UL 60950-1, first edition, Information Technology Equipment Safety - Part 1: General requirements (RD), as applicable for the country where the product will be used. Wherever there is a conflict between the requirements of this document and the RD, the requirements of this Standard will prevail. Engine-driven d.c. power generators intended to provide backup power for the battery supply circuit of UPS units are investigated for compliance with the requirements of the Standard for Stationary Engine-Generator Assemblies, UL 2200, and the CSA Standard for Motors and Generators, C22.2 No. 100. UPS that employ hospital grade components identified by the markings "Hospital Only", "Hospital Grade", or a green dot on the body of the component, or otherwise implying suitability for medical use, are evaluated to the requirements of this Standard and CAN/CSA-C22.2 No. 601.1/UL 60601-1, Medical Electrical Equipment - Part 1: General Requirements for Safety. 1.1.3 Exclusions These requirements do not cover UPS units for use as emergency systems or as legally required standby systems, described in Articles 700 and 701, respectively, of the National Electrical Code, ANSI/NFPA 70, and Section 46 of the Canadian Electrical Code, Part I, CSA C22.1. Where considered appropriate, revision of requirements will be proposed and adopted in conformance with the methods employed for development, revision, and implementation of this Standard. NOTE 1 For equipment subject to transient overvoltages exceeding those for Category II according to IEC 60664, additional protection might be necessary. Such additional protection may be located in the mains supply to the equipment or in the equipment as an integral design feature. NOTE 2 Where the additional protection is an integral part of the equipment insulation requirements, CREEPAGE DISTANCES and CLEARANCE distances from the mains through to the load side of the additional protection may be judged as Category III or IV as required. All insulation requirements, CREEPAGE DISTANCES, and CLEARANCE distances on the load side of the additional protection may be judged as Category I or II as required. This Standard does not cover all types of UPS, but it may be taken as a guide for such equipment. Requirements additional to those specified in this Standard are in some cases necessary for specific applications, e.g.: a) equipment intended for operation while exposed, for example, to extremes of temperature; to excessive dust, moisture, or vibration; to flammable gases; to corrosive or explosive atmospheres; and b) UPS equipment based on rotary machinery.

Uninterruptible Power Systems

IEC 62053-52:2005 电量测量设备(交流电).特殊要求.第52部分:符号

This part of IEC 62053 applies to letter and graphical symbols intended for marking on and identifying the function of electromechanical or static a.c. electricity meters and their auxiliary devices. The symbols specified in this standard shall be marked on the name-plate, dial plate, external labels or accessories, or shown on the display of the meter as appropriate.

Electricity metering equipment (AC) - Particular requirements - Part 52: Symbols

IEC 62055-31:2005 电度表.支付系统.第31部分:特殊要求.电度表用固定支付系统(级别1和2)

This part of IEC 62055 applies to newly manufactured, static watt-hour payment meters of accuracy classes 1 and 2 for direct connection, for the measurement of alternating current electrical energy consumption of a frequency in the range 45 Hz to 65 Hz that include a load switch for the purpose of interruption or restoration of the electricity supply to the load in accordance with the current value of the available credit maintained in the payment meter. It does not apply to static watt-hour payment meters where the voltage across the connection terminals exceeds 600 V (line-to-line voltage for meters for polyphase systems). It applies to payment meters for indoor application only, where the payment meter shall be mounted as for normal service (i.e. together with a specified matching socket where applicable). Payment meters are implementations where all the main functional elements are incorporated in a single enclosure, together with any specified matching socket. There are also multi-part installations where the various main functional elements, such as the measuring element, the user interface unit, token carrier interface, and the load switch are implemented in more than one enclosure, involving additional interfaces. This part of IEC 62055 does not apply to multi-part payment metering installations. Functional requirements that apply to payment meters are also defined in this part of IEC 62055, and include informative basic functional requirements and tests for the prepayment mode of operation in Annex A. Allowances are made for the relatively wide range of features, options, alternatives, and implementations that may be found in practice. The diverse nature and functionality of payment meters prevent the comprehensive specification of detailed test methods for all of these requirements. However, in this case, the requirements are stated in such a way that tests can then be formulated to respect and validate the specific functionality of the payment meter being tested. This part of IEC 62055 does not cover specific functionality or performance requirements for safety, circuit protection, isolation or similar purposes that may be specified through reference to other specifications or standards. This part of IEC 62055 does not cover software requirements. Software requirements for basic energy meter metrology are under consideration for the IEC 62059 series of standards, and in other organisations. This part of IEC 62055 covers type-testing requirements only. For acceptance testing, the concepts given in IEC 61358 may be used as a basic guideline. Dependability aspects are addressed in the IEC 62059 series of standards. This part of IEC 62055 does not cover conformity tests and system compliance tests that may be required in connection with legal or other requirements of some markets.

Electricity metering - Payment systems - Part 31: Particular requirements - Static payment meters for active energy (classes 1 and 2)

AS/NZS 3013:2005 电气装置布线系统元件的防火和机械性能分类

Sets out a classification scheme for wiring systems according to their resistance to the hazards of fire and mechanical damage. Type tests to verify the level of protection provided by a wiring system are given. Intended for reference in other Standards which specify wiring systems with a degree of resistance to damage from fire or mechanical impact.

Electrical installationsClassification of the fire and mechanical performance of wiring system elements

UL 414 BULLETINS-2005 CSDS 8/12/05(12p)

The following changes in requirements are being proposed: 1. Removal of Outdated Enclosure Requirements 2. Clarification of Requirements for Live Parts Mounted on the Underside of an Insulating Base 3. Clarification of Requirements for Metering Transformer Cabinets and Metering Transformer Cabinet Interiors 4. Correction of Reference to a Figure in Paragraph 13.19 5. Clarification of Requirements for Overall Current Rating of a Meter Socket Assembly With More Than One Metering Position 6. Renumbering Sections 25.11 and 25.12 to Properly Identify Short Circuit Requirements 7. Clarification of Marking Requirements in Table 25.1

CSDS 8/12/05 (12p)

NRS 080-2004 配电网络电能损耗的定量和报告

This specification sets out a standard methodology for quantifying and reporting energy loss statistics in the South African Electricity Disctribution Industry by: specifying the process for quantifying energy losses; standardizing the estimation of tech

Quantifying and reporting of energy losses in electricity distribution networks

DIN EN 62054-11:2005 电量测量(交流).电费和负荷控制.第11部分:电子脉动控制接收器的特殊要求

Electricity metering (a.c.) - Tariff and load control - Part 11: Particular requirements for electronic ripple control receivers (IEC 62054-11:2004); German version EN 62054-11:2004

DIN EN 62052-21:2005 电量测量设备(交流).一般要求、试验和试验条件.第21部分:电费和负荷控制设备

Electricity metering equipment (a.c.) - General requirements, tests and test conditions - Part 21: Tariff and load control equipment (IEC 62052-21:2004); German version EN 62052-21:2004

DIN EN 62054-21:2005 电量测量(交流).电费和负荷控制.第21部分:计时开关的特殊要求

Electricity metering (a.c.) - Tariff and load control - Part 21: Particular requirements for time switches (IEC 62054-21:2004); German version EN 62054-21:2004

CECS 174-2004 建筑物低压电源电涌保护器选用、安装、验收和运行规程

本规程适用于频率48~52Hz、标称电压220V/380V供电的建筑物内低压交流电源系统和与其连接的电子设备。

Specification for selection,erection,acceptance and maintanance of surge protective device of low voltage power supply system in building

ANSI C12.9-2005 变压器额定仪表用测试开关

Intended to encompass the dimensions and functions of meter test switches used with transformer-rated watthour meters in conjunction with instrument transformers.

Test Switches for Transformer-Rated Meters

ANSI C12.7-2005 电度表插座要求

Covers the general requirements and pertinent dimensions applicable to watthour meter sockets rated up to and including 600 V and up to and including 320 A continuous duty per socket opening.

Requirements for Watthour Meter Sockets

NRS 064-2005 电力供应行业的空间信息交流导则

Specifies the data to be shared, the format of the data and, the metadata of the data. This specification defines: Mandatory data elements (M) that should be captured and exchanged as a minimum requirement to conform to this specification; Conditional d

Guidelines for the exchange of spatial information in the Electricity Supply Industry

IEC 60364-5-51:2005 建筑物的电气设施.第5-51部分:电气设备的选择和安装.共同规则

Deals with the selection of equipment and its erection. It provides common rules for compliance with measures of protection for safety, requirements for proper functioning for intended use of the installation, and requirements appropriate to the external

Electrical installations of buildings - Part 5-51: Selection and erection of electrical equipment - Common rules