共找到 959 条与 供水系统 相关的标准,共 64 页
1.0.1 为使装配式集成给水系统管道工程的设计、施工、安装、验收及维护管理,做到技术先进、安全卫生、经济合理、确保工程质量,制定本标准。 1.0.2 本标准适用于新建、改建和扩建的民用、工业建筑中给水系统管道工程,采用具有高韧性、耐高温、耐低温、耐压且可弯曲的聚丁烯(PB)管材的集成给水系统管道的设计、施工、安装验收及维护管理。 1.0.3 本标准采用的聚丁烯(PB)材料的管材、管件应符合现行国家标准GB/T 19473.1-2004《冷热水用聚丁烯(PB)管道系统 第1部分 总则》、GB/T 19473.2《冷热水用聚丁烯(PB)管道系统 第2部分:管材》、和GB/T 19473.3《冷热水用聚丁烯(PB)管道系统 第3部分:管件》的规定。 1.0.4 装配式集成给水系统管道工程设计、施工、验收及运行维护,除应符合本标准的规定外,尚应符合国家现行有关标准的规定。
Technical specification for polybutylene(PB)pipeline engineering of building water supply
Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 5: Fitness for purpose of the system - Amendment 1 (ISO 22391-5:2009/Amd 1:2020, Corrected version 2021-03)
Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 2: Pipes - Amendment 2 (ISO 15877-2:2009/Amd 2:2020)
Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 5: Fitness for purpose of the system - Amendment 2 (ISO 15877-5:2009/Amd 2:2020)
Polypropylene (PP) valves for piping systems for water supply under pressure - Types, dimensions and requirements
Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 5: Fitness for purpose of the system
Electric appliances connected to the water mains - Avoidance of backsiphonage and failure of hose-sets (Amendment)
Building valves - Expansion valves - Tests and requirements
主要技术内容包括:总则,术语和符号,材料,设计,施工,管道系统水压试验、冲洗和消毒,竣工验收等。
Technical regulations for buried biaxially oriented polyvinyl chloride (PVC-O) water supply pipeline engineering
本标准规定了居住小区排水管道混接排查与改造的术语和定义、基本规定、混接小区筛查、混接类型、探查与检测方法、混接状况评估、混接改造等工作的原则、要求和内容。
Regulations for investigation and reconstruction of drainage pipes in residential quarters
活性炭选用与检测、活性炭池、粉末活性炭。
Applied technical regulation of activated carbon in municipal water supply plant
5.1 城镇给水颗粒计数在线监测仪的性能应满足表 1 的要求。 5.2 城镇给水颗粒计数在线监测仪的其他功能按照表 2。 5.3 城镇给水颗粒计数在线监测仪的性能指标检验方法见附录 A。
Technical specification for on-line particle count monitor for urban water supply system
一般要求、气源装置、臭氧发生器、臭氧投加装置、臭氧接触池、臭氧尾气消除装置、水质。
Technical specification for inspection and evaluation of ozone system for water treatment
Technical specification for the application of intelligent pump room in the secondary water supply system of cities and towns in Heilongjiang Province
Building water meter configuration specification
Service Standards for Urban Gas Operating Enterprises in Heilongjiang Province
本文件规定了大型立式耐磨单级单吸离心泵(以下简称“泵”)的术语和定义、型式、型号和基本参数、要求、检验方法、检验规则及标志、包装、运输、贮存。 本文件适用于输送液体中含砂量5.5 kg/m3~110kg/m3、砂粒粒径0.264 mm~1mm、流量大于10000m3/h的泵。
Large type wearable vertical single-stage single-suction centrifugal pump
团体标准对不锈钢管及管件种类、型式、尺寸等进行了描述,规定了给水用不锈钢管及管件术语和定义、规格尺寸、技术要求、试验方法、标志、包装、运输和贮存;标准主要适用公称尺寸不大于DN100、公称压力不大于PN25、温度不大于95℃的给水不锈钢管路用不锈钢管及管件的设计、制造和检验。
Stainless steel pipe and fitting for water supply
Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 5: Fitness for purpose of the system — Amendment 1
Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 2: Pipes — Amendment 1
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号