91.190 建筑附件 标准查询与下载

GOST 10922-2012 钢筋混凝土结构用焊接加固产品和搭接、焊接的插入物及机械接头.通用规格

Welded reinforcing products and inserts, welded, lap and mechanical joints for reinforced concrete structures. General specifications

ANSI/BHMA A156.24-2012 出口处延时锁系统

Delayed Egress Locking Systems

EN 12320:2012 构建硬件-挂锁和挂锁配件要求和测试方法

This European Standard applies to mechanical padlocks and padlock fittings used on buildings and general use and specifies the test methods to be used. This European Standard specifies performance and other requirements for strength, security, durability, performance, and corrosion resistance of padlocks. It establishes one category of use, two categories of durability, six categories for corrosion resistance and six grades for security based on performance tests that simulate attack. Limited manual attack testing is included in this European Standard because the machine testing does not replicate all known manual attacks.

Building hardware - Padlocks and padlock fittings - Requirements and test methods

EN 15684:2012 建筑五金.机电一体化汽缸.试验方法和要求

This European Standard specifies requirements for performance and testing of Mechatronic Cylinders and their keys and/or electronic keys.It applies to cylinders for such locks designed to be normally used in buildings. It also applies to cylinders for use with other hardware products such as exit devices, door operators, etc. or monitoring facilities and alarm systems. It establishes categories of use based on performance tests and grades of security based on designrequirements and on performance tests that simulate attack.This European Standard includes assessment of additional features when they are included in the cylinderdesign.This European Standard does not involved in the control of a cylinder. cover any other element of a security system, other than those directly The suitability of cylinders for use on fire or smoke-door assemblies is determined by fire performance testsconducted in addition to the performance testing specified byThis European Standard; see Annex A.

Building hardware - Mechatronic cylinders - Requirements and test methods

BS EN 13126-5:2011 建筑五金.窗和落地窗用建筑五金.要求和试验方法.开窗限制设备

Building hardware. Hardware for windows and door height windows. Requirements and test methods. Devices that restrict the opening of windows and door height windows

BS EN 13126-1:2011 建筑五金.窗和落地窗用建筑五金.要求和试验方法.所有类型五金的通用要求

Building hardware. Hardware for windows and door height windows. Requirements and test methods. Requirements common to all types of hardware

BS EN 13126-3:2011 建筑五金.窗和落地窗用建筑五金.要求和试验方法.倾斜和旋转,先倾斜和只旋转的五金手柄

Building hardware. Hardware for windows and door-height windows. Requirements and test methods. Handles, primarily for Tilt&Turn, Tilt-First and Turn-Only hardware

DS/EN 13126-2:2011 建筑五金 门窗高度窗的要求和试验方法 第2部分：窗紧固件把手

This European Standard specifies requirements and test methods for durability, strength, security and functionality of window fastener handles.This European Standard does not apply to the following hardware:a) handles - primarily for Tilt & Turn, Tilt-First and Turn-Only hardware, refer to EN 13126-3;b) electromechanical hardware.

Building hardware - Requirements and test methods for windows and doors height windows - Part 2: Window fastener handles

NF P26-330-2:2011 建筑五金.窗户和门上窗的要求和试验方法.第2部分:窗紧固把手

Building hardware - Requirements and test methods for windows and doors height windows - Part 2 : window fastener handles.

DIN EN 13126-2:2011 建筑五金.门窗高度窗要求及试验方法.第2部分:窗撑柄.德文版 EN 13126-2-2011

This European Standard specifies requirements and test methods for durability, strength, security and functionality of window fastener handles.

Building hardware - Requirements and test methods for windows and door height windows - Part 2: Window fastener handles; German version EN 13126-2:2011

BS EN 13126-2:2011 建材硬件.窗户和门高度的要求和试验方法.窗户紧固件手柄

Building hardware. Requirements and test methods for windows and doors height windows. Window fastener handles

GSO EN 1935:2011 施工设备 单轴接头 要求和测试方法

This European Standard specifies requirements for single-axis hinges, of lift-off or fixed pin type, for use on access windows and doors. Such windows and doors may or may not be fitted also with door closing devices. It includes tests for static loads, shear strength and allowable wear during durability cycling for the following hinges: a)mounted on the edge of the door leaf or window sash and opening in one direction only; b)whose axis of rotation is within 30 mm of an edge of the movable element for a door leaf mass of up to 160 kg; c)whose axis of rotation is within 30 mm of the edge for a window sash with a mass up to 60 kg. This European Standard classifies hinges for four categories of use (see annex A) and also specifies the maximum permissible torque arising from frictional resistance generated within the hinge during endurance testing. Corrosion protection requirements are specified for those hinges which are not intended to be protected after fitting. There are no restrictions on the materials or the methods of fabrication used providing the hinge conforms to the requirements relevant to its application. The suitability of single axis hinges for use on fire/smoke compartmentation door assemblies is determined by performance tests conducted in addition to the performance tests required by this European Standard. Annex B indicates additional requirements for these products. This European Standard does not apply to hinges incorporating spring-assisted door-closing mechanisms. Door closers incorporating door co-ordinator devices (with or without electrically powered hold-open devices) are covered by EN 1158. Although the fastenings used to fix hinges to window assemblies and door assemblies are not covered by this European Standard, if the type of fastening to be used is supplied or specified by the manufacturer, such fastenings are used for the tests. NOTE Performance standards for complete windows and door assemblies (in the course of preparation byCEN/

Building hardware - Single-axis hinges - Requirements and test methods

GSO EN 1155:2011 建筑五金 电动铰链开门器 要求和测试方法

Please read the qualifying note at the end of the summary of the directive. This European Standard specifies requirements for separate hold-open devices and also for hold-open mechanisms incorporated in a door closer. Electrically powered hold-open devices for swing doors manufactured according to this European Standard can hold a swing door at a fixed position or can allow the door to swing freely. In each case interruption of the electrical supply will cause the controlled door to close positively. Electrically powered hold-open devices manufactured in accordance with this European Standard are recommended for use wherever there is a requirement for reliable hold-open and release of self closing fire/smoke door assemblies. Whilst these devices can incorporate smoke or fire detection elements, the performance of those particular elements is outside of the scope of this European Standard. NOTE : The series of European Standards EN 54 covers the requirements, test methods and performance criteria of resettable smoke/fire detectors.

Building hardware - Electrically powered hold-open devices for swing doors - Requirements and test methods

GSO EN 1125:2011 建筑硬件 水平屏障紧急出口装置 要求和测试方法

This European Standard specifies requirements for the manufacture, performance and testing of panic exit devices mechanically operated by either a horizontal push-bar or a horizontal touch-bar, specifically designed for use in a panic situation on escape routes. The suitability of a panic exit device for use on fire/smoke resisting door assemblies is determined by fire performance tests conducted in addition to the performance tests required by this European Standard. Annex B indicates additional requirements for these products. This European Standard covers panic exit devices which are either manufactured and placed on the market in their entirety by one producer or produced by more than one producer and subsequently placed on the market as a kit in a single transaction.

Building hardware - Panic exit devices operated by a horizontal bar - Requirements and test methods

LST EN 13126-19-2011 建筑五金 窗户和门高窗的要求和测试方法 第19部分：滑动关闭装置

Building hardware - Requirements and test methods for windows and door height windows - Part 19: Sliding Closing Devices

DIN EN 13126-19:2011 建筑五金.窗户和门上窗的要求和试验方法.第19部分:滑动式闭合装置;德文版本EN 13126-19-2011

This part of EN 13126 specifies requirements and test procedures for durability, strength, security and functionality of Sliding Closing Devices (SCD) for windows and door height windows.

Building hardware - Requirements and test methods for windows and door height windows - Part 19: Sliding Closing Devices; German version EN 13126-19:2011

DS/EN 13126-19:2011 建筑五金 窗户和门高窗的要求和测试方法 第19部分：滑动关闭装置

This part of EN 13126 specifies requirements and test methods for durability, strength, security and functionality of Sliding Closing Devices (SCDs) for windows and door height windows.This European Standard does not specifically cover the handles used in handle-operated SCDs or the sash fasteners used in cam-operated SCDs, requirements and test methods for which are given in EN 13126-3 and EN 13126-14, respectively.

Building hardware - Requirements and test methods for windows and door height windows - Part 19: Sliding Closing Devices

BS EN 13126-19:2011 建筑五金 窗户和门上窗的要求和试验方法 推拉关闭装置

Building hardware. Requirements and test methods for windows and door height windows. Sliding closing devices

EN 13126-19:2011 建筑五金.窗户和门上窗的要求和试验方法.推拉关闭装置

This part of EN 13126 specifies requirements and test methods for durability, strength, security and functionality of Sliding Closing Devices (SCDs) for windows and door height windows.This European Standard does not specifically cover the handles used in handle-operated SCDs or the sash fasteners used in cam-operated SCDs, requirements and test methods for which are given in EN 13126-3 and EN 13126-14, respectively.

Building hardware - Requirements and test methods for windows and door height windows - Part 19: Sliding Closing Devices

EN 13126-5:2011 建筑五金件 窗和门高窗的五金件 要求和实验方法 第5部分:限制窗和门高窗开放的设备

This part of EN 13126 specifies requirements and test methods for durability, strength, security and functionality of devices that restrict the opening of windows and door height windows. NOTE 1 Restrictors and reverse restrictors can be either a separate item of hardware or an integral part of hardware, for example a part of the operating gear or an integral part of a hinge. NOTE 2 Windows may be fitted with more than one restrictor. NOTE 3 The requirements included withinThis standard take the needs for child safety into consideration, child protective window restrictors intended to be installed by the end consumers are beyond the scope of this standard. Therefore, for the DIY market refer to PC398 and prEN 16281.

Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 5: Devices that restrict the opening of windows and door height windows