共找到 594 条与 建筑附件 相关的标准,共 40 页
Building hardware - Mechatronic cylinders - Requirements and test methods
Building hardware - Environmental product declarations - Product category rules complementary to EN 15804 for building hardware
Operating forces - Test method - Part 1: Windows
本文件规定了抗菌门锁的术语和定义、要求、试验方法、检验规则、标志、包装、运输和贮存。
Antibacterialdoor lock
规定了建筑门窗五金件窗用防坠装置的术语和定义、分类和标记、要求、试验方法、检验规则及标志、包装、运输和贮存。
Architectural door and window hardware window with anti-drop device
规定了建筑门窗传动机构定位执手的术语和定义、分类和标记、要求、试验方法、检验规则及标志、包装、运输和贮存。
Architectural door and window hardware transmission mechanism positioning handle
本标准规定了民用建筑多参数室内环境监测仪器的术语和定义,分类与标记,一般要求,性能要求,试验方法,检验规则,标志、包装、运输与储藏。
Multi-parameter indoor environment monitoring instrument for civil buildings
BS EN 13126-2. Building hardware. Hardware for windows and door height windows. Requirements and test methods - Part 2. Window fastener handles
BS EN 12209. Building hardware. Mechanically operated locks and locking plates. Requirements and test methods
BS EN 15685. Building hardware. Requirements and test methods. Multipoint locks, latches and locking plates. Characteristics and test methods
本标准规定了防雾霾窗纱的术语和定义、技术要求、测试方法、检验规则、标志、包装、运输和贮存。 本标准适用于具有过滤PM2.5颗粒物功能的各种类型窗纱。
Anti-smog window screen
本标准规定了铝框塑料模板的术语和定义、分类、规格和标记、要求,试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于现浇混凝土施工用铝框塑料模板。
Aluminum frame plastic formwork
1.1 These test methods cover the apparatus, procedures, and acceptance conditions for evaluating the normal operational performance and the performance characteristics under assault conditions of locks used in swinging door assemblies in detention and correctional institutions. Thus, they give only an indication of the performance characteristics of locks in actual service. Such variables as installation and maintenance conditions are not considered. 1.2 It is the intent of these test methods to help ensure that detention locks perform at or above minimum acceptable levels to control passage to unauthorized or secure areas, to confine inmates, and to delay and frustrate escape attempts and resist vandalism. It is recognized that in order to meet the intent of these test methods, door and frame assemblies must be compatible with the level of performance required by Test Methods F1450. 1.3 The values stated in inch-pound units are to be regarded as the standard. The values in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Test Methods for Detention Locks for Swinging Doors
1.1 These test methods cover the apparatus, procedures, and acceptance conditions for evaluating the normal operational performance and the performance characteristics under assault, smoke, and fire conditions of sliding device assemblies in detention and correctional institutions. These test methods give an indication of the performance characteristics of devices in actual service. Such variables as installation and maintenance conditions are not considered. 1.2 It is the intent of these test methods to help ensure that detention sliding devices perform at or above minimum acceptable levels to control passage to unauthorized or secure areas, to confine inmates and to delay and frustrate escape attempts and resist vandalism. However, these test methods do not address door construction. It is recognized that in order to meet the intent of these test methods, door assemblies shall be compatible with the level of performance required by Test Methods F1450. 1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Test Methods for Detention Sliding Door Locking Device Assembly
5技术要求 5.1 原材料要求 (MCMP)方形管用的材料是以多组分改性聚氯乙烯树脂为原料,经挤出成型符合本标准要求的新型复合增强管材。改性材料不得加入增塑剂,填料的含量不超过5%。 5.2 产品要求 5.2.1 颜色、外观、尺寸 5.2.1.1 颜色 管材颜色一般为橘红色,其它颜色由供需双方协商确定,色泽应均匀一致。 5.2.1.2 外观 (MCMP)方形管内外壁不应有气泡、裂口、明显的杂质、 分解变色线、不规则的波纹,内壁应光滑平整。 5.2.1.3 尺寸 规格尺寸及偏差符合表 1 的规定,长度一般为 6.2m,也可以供需双方的商定。(MCMP)方形管长度应包括圆管接头部分的长度,长度极限负偏差为长度的0.5%。 5.3 技术性能 5.3.1 (MCMP)方形管的技术性能符合表2规定。 表2 改性聚氯乙烯(MCMP)方形双壁波纹管技术性能要求 项 目 单位 技术指标 试验方法 密度 kg/m3 ≤1500 6.3 维卡软化温度 ℃ ≥93 6.4 烘箱试验 - 无分层、无裂纹 6.5 扁平试验 - 压缩至管内壁互相接触,试样不应出现破裂、分层或起皮 6.6 抗外压负载性能 N/200mm S1≥4000,S2≥5500 6.7 落锤冲击试验 - 10/10通过 6.8 阻燃性 氧指数OI % ≥32 6.9.1 阻燃等级 - V-0,离火即熄、无滴落。 6.9.2 体积电阻率 Ω?m ≥1×1011 6.10 静摩擦系数 - ≤0.35 6.11 连接密封性(0.01MPa 水压,在 20℃下保持 30min) - 无泄漏 6.12
Modified polyvinyl chloride (MCMP) square double-wall corrugated pipe for electric power and communication
Test method for door fittings of buildings -- Part 2: Fittings for door
本规程的主要技术内容:1. 总则;2. 术语和符号;3. 基本规定;4. 材料;5.设计;6施工;7.验收;附录。
Specification for water and drainage pipeline rehabilitation using cured-in-place-pipe method
本标准共分6章和1个附录,主要技术内容包括:总则、术语、基本规定、智慧家居系统框架、智慧家居子系统功能要求和智慧家居系统等级划分。
Design Standard for Smart Home
本规程共分为7章,主要内容包括:总则、术语、基本规定、系统及其组成材料、设计、施工、质量验收。
Technical specification for insulation system based on silica rock insulation board
本规程共分7章,主要内容包括:总则、术语和符号、系统设计、系统计算和选型、安装、测试和验收、维修管理等。
Technical specification for indoor vacuum drainage system engineering
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号