93.030 外部污水排放系统 标准查询与下载
共找到 513 条与 外部污水排放系统 相关的标准，共 35 页
This European Standard applies for components for vitrified clay manholes and inspection chambers for buried drain and sewer systems for the conveyance of wastewater (including domestic wastewater, surface water and rainwater) under gravity and periodic hydraulic surcharge or under continuous low head of pressure.It specifies different strength classes and heights of sections. It also specifies the requirements for components used for joints, systems of joint dimensions and the materials rubber, polyurethane and polypropylene used for joints. This standard does not apply to manhole tops and cover slabs.
Vitrified clay pipes systems for drain and sewers - Part 6: Requirements for components of manholes and inspection chambers [Superseded: CEN EN 295-10]
- ICS
- 93.030
- CCS
- 发布
- 2013-02-01
- 实施
This European Standard specifies requirements for vitrified clay pipes, fittings and flexible joints for buried drain and sewer systems for the conveyance of wastewater (including domestic wastewater, surface water and rainwater) under gravity and periodic hydraulic surcharge or under continuous low head of pressure.This standard also specifies requirements for rubber, polyurethane and polypropylene materials and other components used for jointing clay pipes and fittings.This standard specifies different strength classes, systems of joint dimensions, lengths and fittings. This standard does not apply to special fittings, adaptors and compatible accessories,
Vitrified clay pipe systems for drains and sewers - Part 1: Requirements for pipes, fittings and joints [Superseded: CEN EN 295-10]
- ICS
- 93.030
- CCS
- 发布
- 2013-02-01
- 实施
This European Standard specifies the required properties of the piping system and its components made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) intended to be used for drainage or sewerage, including culverts, with or without pressure. In a pipework system, pipes and fittings of different nominal pressure and stiffness ratings may be used together. It is the responsibility of the purchaser or specifier to make the appropriate selections taking into account their particular requirements and any relevant national regulations and installation practices or codes. This European Standard is applicable to GRP-UP, with flexible or rigid joints (see 3.33 and 3.34), primarily intended for use in buried installations. NOTE Piping systems conforming to this European Standard can be used also for non-buried applications provided that the influence of the environment, e. g. from UV-radiation, and the supports are considered in the design of the pipes, fittings and joints. It is applicable to pipes, fittings and their joints of nominal sizes from DN 100 to DN 4000, which are intended to be used for the conveyance of surface water or sewage at temperatures up to 50 °C, with or without pressure. This European Standard covers a range of nominal sizes, nominal stiffnesses and nominal pressures. Clause 6 is applicable to fittings made using any of the following techniques: a) fabricated from straight pipe; b) moulded by: 1) filament winding; 2) tape winding; 3) contact moulding; 4) hot or cold press moulding. This European Standard is applicable to the joints to be used in GRP-UP piping systems to be used for the conveyance of water, both buried and non-buried. It is applicable to joints, which are or are not intended to be resistant to axial loading. It covers requirements to prove the design of the joint. It specifies type test performance requirements for the following joints as a function of the declared nominal pressure rating of
Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Specifications for pipes@ fittings and joints
- ICS
- 93.030
- CCS
- P41
- 发布
- 2013-02-01
- 实施
- 2013-02-01
This European Standard specifies requirements for the evaluation of conformity of products manufactured from vitrified clay and other materials (referred to as "products") specified in the following standards:pipes, fittings and joints according to EN 295-1; adapters, connectors and flexible couplings according to EN 295-4; perforated pipes and fittings according to EN 295-5; components of manholes and inspection chambers according to EN 295-6; and pipes and joints for pipe jacking according to EN 295-7.
Vitrified clay pipe systems for drains and sewers - Part 2: Evaluation of conformity and sampling [Superseded: CEN EN 295-10]
- ICS
- 93.030
- CCS
- 发布
- 2013-02-01
- 实施
This European Standard specifies requirements for vitrified clay pipes and joints for pipe jacking for buried drain and sewer systems for the conveyance of wastewater (including domestic wastewater, surface water and rainwater) under gravity and periodic hydraulic surcharge or under continuous low head of pressure. Pipe jacking techniques include micro-tunnelling, pipe-eating, pipe bursting and where appropriate lining with discrete pipes. This standard also specifies requirements for rubber, polyurethane, polypropylene, stainless steel and other materials used for joints for pipe jacking.
Vitrified clay pipe systems for drains and sewers - Part 7: Requirements for pipes and joints for pipe jacking [Superseded: CEN EN 295-10]
- ICS
- 93.030
- CCS
- 发布
- 2013-02-01
- 实施
This European Standard specifies requirements for adaptors and connectors made from vitrified clay and/or other suitable materials for use with vitrified clay pipes and fittings for buried drain and sewer systems for the conveyance of wastewater (including domestic wastewater, surface water and rainwater) under gravity and periodic hydraulic surcharge or under continuous low head of pressure.Adaptors and connectors include insertable fittings, sealing rings for cut pipes and heat-shrinkable sleeves.This standard also applies for metal banded flexible couplings and adaptors and specifies requirements for rubber, polyurethane, stainless steel and other compon
Vitrified clay pipe systems for drains and sewers - Part 4: Requirements for adaptors@ connectors and flexible couplings
- ICS
- 93.030
- CCS
- 发布
- 2013-02-01
- 实施
Plastics piping systems for drainage and sewerage. Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP). Manholes and inspection chambers
- ICS
- 93.030
- CCS
- P41
- 发布
- 2013-01-31
- 实施
- 2013-01-31
Investigation and assessment of drain and sewer systems outside buildings - Part 1: General Requirements
- ICS
- 93.030
- CCS
- 发布
- 2013-01-31
- 实施
- 2013-01-31
Plastics piping systems for drainage and sewerage. Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP). Manholes and inspection chambers
- ICS
- 93.030
- CCS
- P41
- 发布
- 2013-01-31
- 实施
- 2013-01-31
This ISO Standard specifies the definitions and requirements for thermoplastics covers and frames formanholes, inspection chambers and other such pipeline access products installed in light vehicularaccess and pedestrian areas and manufactured from unplas
Specifications for thermoplastics covers and frames for manholes and inspection chambers used in non-traffic areas
- ICS
- 93.030
- CCS
- 发布
- 2013-01-18
- 实施
- 2013-01-18
Technical regulations for detection of urban underground pipelines in Hubei Province
- ICS
- 93.030
- CCS
- P 11
- 发布
- 2013-01-04
- 实施
- 2013-05-01
This European Standard establishes the general principles for the management and control of operational activities in drain and sewer systems outside buildings and specifies requirements for development and implementation of work programmes, and the selection of techniques. This part covers the management and control of rehabilitation activities. It is applicable to drain and sewer systems, which operate essentially under gravity, from the point where wastewater leaves a building, roof drainage system, or paved area, to the point where it is discharged into a treatment works or receiving water. Drains and sewers below buildings are included provided that they do not form part of the drainage system of the building.
Management and control of operational activities in drain and sewer systems outside buildings - Part 2: Rehabilitation
- ICS
- 93.030
- CCS
- 发布
- 2013-01-01
- 实施
This European Standard is applicable to the investigation and assessment of drain and sewer systems outside buildings. It is applicable to drain and sewer systems,which operate essentially under gravity,from the point where the sewage leaves a building or roof drainage system,or enters a road gully,to the point where it is discharged into a treatment works or receiving water. Drains and sewers below buildings are included provided that they do not form part of the drainage system of the building.
Investigation and assessment of drain and sewer systems outside buildings.Part 1: General requirements; German version EN 13508-1:2012
- ICS
- 93.030
- CCS
- P41
- 发布
- 2013-01
- 实施
Specification for 12 to 60 in. (300 to 1500 mm) Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Gravity-Flow Storm Sewer and Subsurface Drainage Applications
- ICS
- 93.030
- CCS
- Q81
- 发布
- 2013
- 实施
Specification for quality inspection and evaluation of asphalt pavement maintenance engineering
- ICS
- 93.030
- CCS
- R 18
- 发布
- 2012-11-05
- 实施
- 2012-12-05
Investigation and assessment of drain and sewer systems outside buildings. General Requirements
- ICS
- 93.030
- CCS
- P41
- 发布
- 2012-10-31
- 实施
- 2012-10-31
This Technical Specification gives guidance for the assessment of conformity of materials, products, joints and assemblies in accordance with the applicable part(s) of EN 12666 intended to be included in the manufacturer"s quality plan as part of the qual
Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE) - Part 2: Guidance for the assessment of conformity
- ICS
- 93.030
- CCS
- 发布
- 2012-10-18
- 实施
- 2012-10-18
Prefabricated concrete manholes, unreinforced, steel fibre and reinforced - Part 10: Brick manhole bases for buried drains and sewers - Requirements and testing
- ICS
- 93.030
- CCS
- Q14
- 发布
- 2012-10-01
- 实施
This Technical Specification gives guidance for the assessment of conformity of compounds/formulations, products and assemblies in accordance with Parts 1 and 2 of EN 13598 intended to be included in the manufacturer"s quality plan as part of the quality
Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride)(PVC-U), polypropylene (PP) and polyethylene (PE) - Part 3: Guidance for assessment of conformity
- ICS
- 93.030
- CCS
- 发布
- 2012-08-31
- 实施
- 2012-08-31
Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 3: Guidance for assessment of conformity; German version CEN/TS 13598-3:2012
- ICS
- 93.030
- CCS
- Q81
- 发布
- 2012-07
- 实施
