93.030 外部污水排放系统 标准查询与下载

EN 13598-2:2009 无压力地下排水和排污用塑料管道系统.未增塑聚氯乙烯(PVC-U),聚丙烯(PP)和聚乙烯(PE).第2部分:交通范围和地下设施中检修孔和检查室用规范

This European Standard specifies the definitions and requirements for buried manholes and inspection chambers installed to a maximum depth of 6 m from ground level to the invert of the main chamber and manufactured from unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP), polypropylene with mineral modifier (PP-MD) or polyethylene (PE). These products are intended for use in pedestrian or vehicular traffic areas and underground installations conforming to the general requirements given in EN 476 and are used outside the building structure (application area code "U"). They are therefore marked accordingly with a "U". Such products are also deemed to meet the requirements of EN 13598-1 for application area U without the need for further testing. If additionally marked application area D then these products must additionally be tested to show compliance to the elevated temperature cycling requirement of Clause 10 of EN 13598-1.This European Standard is only applicable to those chamber / manhole items where the manufacturer has clearly stated in the documentation how the components shall be assembled to create a complete manhole or inspection chamber. The inspection chambers covered byThis European Standard comprise the following: inspection chambers providing access to the drainage or sewerage system by means of inspection and cleaning equipment. chambers, designated as manholes providing man access to the drainage or sewerage system. The inspection chamber / manhole can be manufactured by various methods e. g. injection moulding, rotational moulding, low-pressure moulding or fabricated from components made in accordance with other standards. The jointing of components can be achieved using: elastomeric ring seal joints; adhesive joints for PVC-U; welded joints for PVC-U, PP and PE; extrusion welding; mechanical jointing. NOTE Both manholes and inspection chambers can be site assembled from different components, but can also be manufactured as a single unit. In either case, the following functional parts can be recognized: a) base (always present) In case of a one-piece chamber or manhole, the base part ends at a distance of 300 mm measured from the top of the main channel; b) riser (depth dependent); c) telescopic part (design dependent); d) cone (dependent on the design of near surface components and their recommended installation); e) other near surface components

Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications for manholes and inspection chambers in traffic areas and deep under

ANSI/ASTM D5926:2009 排水、废水和排气(DWV)、下水道、卫生设施和暴雨管道系统用聚乙烯(PVC)垫圈

Specification for Poly(Vinyl Chloride) (PVC) Gaskets for Drain, Waste, and Vent (DWV) , Sewer, Sanitary, and Storm Plumbing Systems

ASTM D7498-09 垂直地带排水大规模应力测试的标准试验方法

As this is a time intensive test, it should not be considered as an acceptance test for commercial shipments of prefabricated vertical strip drains. Prior to the development of vertical strip drains, when it was desired to increase the rate of consolidation of a compressible soil on a construction project, large diameter sand drains were installed. Vertical strip drains can be installed in areas where it is desired to increase the rate of soils consolidation in place of these large diameter sand drains. This test method can be used to compare the performance of vertical strip drains to that of sand drains.1.1 This test method is a performance test, which measures the effectiveness of vertical strip drains on the time rates of consolidation of compressible soils from construction project sites. 1.1.1 It is expected that the design agency will be responsible for performing this test. It is not intended to be a manufacturer performed test. 1.2 This test method is applicable to all vertical strip drains. 1.3 The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Vertical Strip Drains Using a Large Scale Consolidation Test

DIN CEN/TS 13476-4:2008 非受压地下排水和排污用塑料管道系统.未增塑聚氯乙烯(PVC-U)、聚丙烯(PP)和聚乙烯(PE)的结构壁管道系统.第4部分:一致性评估用指南

Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 4: Guidance for the assessment of conformity; German

DIN 19572:2008 人孔入口处的把手.要求、试验

Handholds for entrance into accessible manholes - Requirements, testing

CJ/T 289-2008 城镇污水处理厂污泥处置.制砖用泥质

本标准规定了城镇污水处理厂污泥制烧结砖利用的泥质指标、取样和监测等技术要求。 本标准适用于城镇污水处理厂污泥的处置和污泥制烧结砖利用。

The disposal of sludge from municipal wastewater treatment plant.The quality of sludge used in making brick

CJ/T 290-2008 城镇污水处理厂污泥处置.单独焚烧用泥质

本标准规定了城镇污水处理厂污泥单独焚烧时的泥质指标、取样和监测等技术要求。 本标准适用于城镇污水处理厂污泥处置规划、设计和管理。

The disposal of sludge from municipal wastewater treatment plant.Sludge quality for separate incineration

CJ/T 291-2008 城镇污水处理厂污泥处置.土地改良用泥质

本标准规定了用于土地(盐碱地、沙化地和废弃矿场土壤)改良的城镇污水处理厂污泥泥质准入标准，规定了污泥施用时的技术要求和注意事项。 本标准适用于城镇污水处理厂污泥处置规划、设计和管理。 排水管道通挖污泥用于土地改良的泥质可参照本标准。

The disposal of sludge from municipal wastewater treatment plant.Sludge quality for land improvement

DIN 19523:2008 排水沟和下水道部件的抗喷射测定用要求和试验方法

Requirements and test methods for determination of the jetting resistance of components of drains and sewers

DIN EN 1917 Berichtigung 2:2008 无钢筋和带钢筋的混凝土检修孔和检验井.技术勘误DIN EN 1917-2003

Concrete manholes and inspection chambers, unreinforced, steel fibre and reinforced; German version EN 1917:2002, Corrigendum to DIN EN 1917:2003-04; German version EN 1917:2002/AC:2008

LST EN 1917-2003/AC-2008 混凝土检修孔和检查室，未加固、钢纤维和加固

Concrete manholes and inspection chambers, unreinforced, steel fibre and reinforced

DB21/T 1626-2008 埋地钢塑复合螺旋缠绕排水管道工程技术规程

Engineering technical specification for buried steel-plastic composite spiral winding drainage pipeline

BS EN 752:2008 建筑物外部排水和污水系统

This European Standard sets out the objectives for drain and sewer systems outside buildings. It specifies the functional requirements for achieving these objectives and the principles for strategic and policy activities relating to planning, design, installation, operation, maintenance and rehabilitation. It is applicable to drain and sewer systems, which operate essentially under gravity, from the point where wastewater leaves a building, roof drainage system, or paved area, to the point where it is discharged into a wastewater treatment plant or receiving water. Drains and sewers below buildings are included provided that they do not form part of the drainage system for the building.

Drain and sewer systems outside buildings

LST EN 752-2008 建筑物外的排水和下水道系统

Drain and sewer systems outside buildings

DIN EN 752:2008 建筑物外部的排污系统

This European Standard sets out the objectives for drain and sewer systems outside buildings. It specifies the functional requirements for achieving these objectives and the principles for strategic and policy activities relating to planning, design, installation, operation, maintenance and rehabilitation. It is applicable to drain and sewer systems, which operate essentially under gravity, from the point where wastewater leaves a building, roof drainage system, or paved area, to the point where it is discharged into a wastewater treatment plant or receiving water. Drains and sewers below buildings are included provided that they do not form part of the drainage system for the building.

Drain and sewer systems outside buildings; English version of DIN EN 752:2008-04

DS/EN 752:2008 建筑物外的排水和下水道系统

This European Standard sets out the objectives for drain and sewer systems outside buildings. It specifies the functional requirements for achieving these objectives and the principles for strategic and policy activities relating to planning, design, installation, operation, maintenance and rehabilitation.It is applicable to drain and sewer systems, which operate essentially under gravity, from the point where wastewater leaves a building, roof drainage system, or paved area, to the point where it is discharged into a wastewater treatment plant or receiving water. Drains and sewers below buildings are included provided that they do not form part of the drai

Drain and sewer systems outside buildings

NF P16-150:2008 建筑物外部污水排放系统

Drain and sewer systems outside buildings.

CEN EN 752-2008_ 建筑外沟渠及污水渠系统

This European Standard sets out the objectives for drain and sewer systems outside buildings. It specifies the functional requirements for achieving these objectives and the principles for strategic and policy activities relating to planning, design, installation, operation, maintenance and rehabilitation. It is applicable to drain and sewer systems, which operate essentially under gravity, from the point where wastewater leaves a building, roof drainage system, or paved area, to the point where it is discharged into a wastewater treatment plant or receiving water. Drains and sewers below buildings are included provided that they do not form part of the drainage system for the building.

Drain and sewer systems outside buildings

ANSI/ASTM F2562/F 2562M:2008 非压力排水和排污用钢加固的热塑性加肋管和配件用规范

This specification covers requirements and test methods for materials, dimensions, workmanship, impact resistance, pipe stiffness, flattening, buckling, tensile strength of seam, joint systems, perforations, and markings for steel reinforced thermoplastic pipe and fittings of nominal sizes 8 in. [200 mm] through 120 in. [3000 mm]. The steel reinforced, spirally formed thermoplastic pipes governed by this standard are intended for use in underground applications where soil provides support for their flexible walls. These pipes will be used for gravity flow and non-pressure applications, such as storm sewers, sanitary sewers, industrial waste applications and drainage pipes. Units -The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text the SI units are shown in brackets. The values stated in each system may not be exact equivalents: therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. There is no similar or equivalent ISO standard.

Specification for Steel Reinforced Thermoplastic Ribbed Pipe and Fittings for Non-Pressure Drainage and Sewerage

LST EN 1123-2+A1-2007 废水系统用带插口和承口的纵向焊接热浸镀锌钢管的管道和配件 第2部分：尺寸

Pipes and fittings of longitudinally welded hot-dip galvanized steel tube with spigot and socket for waste water systems - Part 2: Dimensions