93.030 外部污水排放系统 标准查询与下载

BS EN 1123-2+A1:2007 废水系统用带套管和座孔的径向焊接热浸镀锌钢管的管道和配件 第2部分：尺寸

Pipes and fittings of longitudinally welded hot-dip galvanized steel tube with spigot and socket for waste water systems - Dimensions

CJ 247-2007 城镇污水处理厂污泥泥质

本标准规定了城镇污水处理厂污泥中污染物的控制项目和限值。 本标准适用于城镇污水处理厂的污泥。 居民小区的污水处理设施的污泥，可参照本标准执行。

Quality of sludge from municipal wastewater treatment plant

ANSI/ASTM F2510/F 2510M:2007 钢筋混凝土人孔结构和波纹状高密度聚乙烯排水管间弹性连接件的规范

This specification covers the design, material, and minimum performance requirements of resilient connectors used for connections between reinforced concrete structures conforming to Specifications C 478 and C 913 to annular corrugated profile wall high density polyethylene (HDPE) drainage pipe conforming to AASHTO M252 or Specification F 2306/F 2306M. These connectors are designed to provide a positive seal between the pipe and manholes or other structures subjected to internal and external hydrostatic pressures less than 10.8 psi [74 KPa]. Testing under this standard is limited to hydrostatic pressures. Alternate air and vacuum pressure testing involve unique testing protocols and are not addressed under this standard. Testing under this standard is conducted in a laboratory as a proof of design certification. Actual field performance testing would be accomplished and accepted under individual project performance standards or pipeline acceptance criteria, which is outside the scope of this standard. Note 1 -Infiltration or exfiltration quantities for an installed system are dependent upon many factors other than the connections between manhole structures and pipe, and allowable quantities must be covered by other specifications and suitable testing of the installed pipeline and system. Note 2 -This specification may be applied to other types of plastic drainage pipe. Consult with manufacturer of pipe for applicability to this standard. The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text the SI units are shown in brackets. The values stated in each system may not be exact equivalents: therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The following precautionary caveat pertains only to the test methods portion, Section 7. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific precaution statement, see 7.2.3.

Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures and Corrugated High Density Polyethylene Drainage Pipes

DIN EN 14982:2006 热塑管道和导管系统.监测室和人孔用热塑性轴或升降管.环的硬度测定

This European Standard specifies a test method for assessing the initial (short-term) tangential ring stiffness of riser shafts for thermoplastics inspection chambers or manholes. NOTE This is intended as a test of the structural integrity of riser shafts supporting product standards prEN 13598-2[1] and prEN 15229[2].

Plastics piping and ducting systems - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of ring stiffness; English version of DIN EN 14982:2006-12

DS/CEN/TS 14758-3:2006 非压力地下排水和污水处理用塑料管道系统 含矿物改性剂的聚丙烯（PP-MD） 第3部分：安装指南

This Technical Specification, together with ENV 1046 and EN 1610, provides a material-specific set of guidelines for the installation of piping systems made of polypropylene with mineral modifier(s) (PP-MD) in the field of non-pressure underground drainage and sewerage.- outside the building structure (application area code """"U"""");- both buried in ground within the building structure (application area code """"D"""") and outside the building.This is reflected in the marking of products by """"U"""" and """"UD"""".""

Plastics piping systems for non-pressure underground drainage and sewerage – Polypropylene with mineral modifier(s) (PP-MD) – Part 3: Guidance for installation

BS EN 14364+A1:2006 地下压力排水和排污水塑料管道系统 不饱和聚酯树脂（UP）基玻璃纤维增强的热固性塑料（GRP） 管道、配件和连接件规格

Plastics piping systems for drainage and sewerage with or without pressure. Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP). Specifications for pipes, fittings and joints

BS EN 14364:2006 地下压力排水和排污水塑料管道系统.未饱和聚酯树脂(UP)玻璃纤维增强的热固性塑料(GRP).管道、配件和连接件的规范

This European Standard specifies the required properties of the piping system and its components made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) intended to be used for drainage or sewerage with or without pressure. In a pipework system, pipes and fittings of different nominal pressure and stiffness ratings may be used together. NOTE 1 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. This European Standard is applicable to GRP-UP, with flexible or rigid joints (see 3.37 and 3.38), primarily intended for use in buried installations. NOTE 2 Piping systems conforming to this European Standard can be used also for non-buried applications provided the influence of the environment, e.g. from UV-radiation, and the supports are considered in the design of the pipes, fittings and joints. It is applicable to pipes, fittings and their joints of nominal sizes from DN 100 to DN 3000, which are intended to be used for the conveyance of surface water or sewage at temperatures up to 50 °C, with or without pressure. This European Standard covers a range of nominal sizes, nominal stiffnesses and nominal pressures. Clause 4 specifies the general aspects of GRP-UP piping system intended to be used in the field of drainage or sewerage, with or without pressure. Clause 5 specifies the characteristics of pipes made from GRP-UP with or without aggregates and/or fillers. The pipes can have a thermosetting or thermoplastics liner. Clause 5 also specifies the test parameters for the test methods referred to in this European Standard. Clause 6 specifies the characteristics of fittings made from GRP-UP with either a thermosetting or thermoplastics liner intended to be used in the field of drainage or sewerage. Clause 6 specifies the dimensional and performance requirements for bends, branches, reducers, saddles and flanged adaptors and it also specifies the test parameters for the test methods referred to in this European Standard. Clause 6 is applicable to fittings made using any of the following techniques: a) fabricated from straight pipe; b) moulded by 1) filament winding; 2) tape winding; 3) contact moulding; 4) hot or cold press moulding. Clause 7 is applicable to the joints to be used in GRP-UP piping systems to be used for the conveyance of water, both buried and non-buried. This specification is applicable to joints, which are or are not intended to be resistant to axial loading. It covers requirements to prove the design of the joint. Clause 7 specifies type test performance requirements for the following joints as a function of the declared nominal pressure rating of the pipeline or system: i) socket-and-spigot (either integral with pipe or sleeve coupling) or mechanical joint; ii) locked socket-and-spigot joint; iii)cemented or wrapped joint; iv) bolted flange joint.

Plastic piping systems for drainage and sewerage with or without pressure - Glass reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Specifications for pipes, fittings and joints

BS DD CEN/TS 14758-3:2006 无压力地下排水和排污塑料管道系统.聚丙烯矿物调节器(s)(PP-MD).安装指南

This Technical Specification, together with ENV 1046 and EN 1610, provides a material-specific set of guidelines for the installation of piping systems made of polypropylene with mineral modifier(s) (PP-MD) in the field of non-pressure underground drainage and sewerage. — outside the building structure (application area code "U"); — both buried in ground within the building structure (application area code "D") and outside the building. This is reflected in the marking of products by "U" and "UD".

Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifier(s) (PP-MD) - Part 3: Guidance for installation

BS EN 13508-2+A1:2006 建筑物外排水和排污系统的调查与评估 目视检查编码系统

Investigation and assessment of drain and sewer systems outside buildings. Visual inspection coding system

BS EN 13508-2:2003+A1:2011 建筑物外排水和排污系统的调查与评估.目视检查编码系统

Investigation and assessment of drain and sewer systems outside buildings. Visual inspection coding system

BS EN 13508-2:2003 建筑物外部排水沟和下水道系统的状态.目视检查编码系统

This European Standard is applicable to the establishment of the condition of drain and sewer systems by inspection, status codification and consideration of external factors and other information. It is applicable to drain and sewer systems, which operate essentially under gravity, from the point where the sewage leaves a building or roof drainage system, or enters a road gully, to the point where it is discharged into a treatment works or receiving water. Drains and sewers below buildings are included provided that they do not form part of the drainage system of the building. This part of the European Standard specifies a coding system for the description of the internal condition of drains, sewers, manholes and inspection chambers identified through visual inspection. Where appropriate, it can also be used for pressure and vacuum systems in accordance with the requirements of the employing authority. This part of the European Standard does not generally specify requirements for carrying out inspections.

Conditions of drain and sewer systems outside buildings — Part 2: Visual inspection coding system

GSO 1756:2006 沙井和防洪产品及其框架的盖和格栅的测试方法

This standard is concerned with methods of test for covers and gratings of manhole and gully and their frames.

Methods of test for covers and gratings of manhole and gully and their frames

PD CEN/TS 14758-3:2006 无压力地下排水和污水塑料管道系统.含矿物调节剂的聚丙烯(PP-MD).第3部分:安装指南

Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifier(s) (PP-MD) - Part 3: Guidance for installation

EN 14364:2006 地下压力排水和排污水塑料管道系统.未饱和聚酯树脂(UP)玻璃纤维增强的热固性塑料(GRP).管道,配件和连接件.包含修改件A1-2008

This European Standard specifies the required properties of the piping system and its components made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) intended to be used for drainage or sewerage with or without pressure. In a pipework system, pipes and fittings of different nominal pressure and stiffness ratings may be used together.

Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Specifications for pipes, fittings and joints Incorporates Amendment A1: 2008

ISO 6594:2006 铸铁排水管和配件.插口系列

This International Standard specifies the characteristics of cast iron drainage pipes and fittings used for the installation of: — discharge pipes for waste and sewage, — rain water pipe systems, and — ventilation pipe systems. The technical specification is applicable to the range of nominal sizes, DN: 40 - 50 - 70 - 75 - 100 - 125 -150 - 200 - 250 - 300 - 400 - 500 - 600. Where applicable, national standards and/or regulations could clarify, and possibly restrict, the field of application of the pipes and fittings covered. In addition, this International Standard gives the dimensions for the most commonly used pipe and fitting sizes. It also provides control testing and test methods for checking compliance with the technical specification and the dimensional and other requirements.

Cast iron drainage pipes and fittings - Spigot series

DIN EN 14758-1:2006 无压地下排水和污水塑料管道系统.有矿物调节剂的聚丙烯(PP-MD)管道系统.第1部分:管、管件和系统规范.德文版本EN 14758-1-2005

This European Standard specifies the requirements for solid-wall pipes," fittings and the system of piping systems made from mineral modified polypropylene materials (PP-MD) in the field of non-pressure underground drainage and sewerage outside the building structure (application area code ""U"")"," and non-pressure underground drainage and sewerage for both buried in ground within the building structure (application area code ""D"") and outside the building structure. This is reflected in the marking of products by ""U"" and ""UD"". It also specifies the test parameters for the test methods referred to in this European standard.#",#

Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings and the system; German version EN 14758-1:2005

NF P16-364-2:2006 地下无压排水和污水管线翻新用塑料管道系统.第2部分:连接管道用内衬

Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 2 : lining with continuous pipes.

DIN EN 13566-2:2006 地下非压力排水排污网翻新用塑料管道系统.第2部分:连续管加衬.德文版本 EN 13566-2-2005

This Part 2 of EN 13566, read in conjunction with Part 1, specifies requirements and test methods for pipes and fittings which are part of plastics piping systems installed as continuous pipes in the renovation of non- pressure drainage and sewerage networks. It covers; -- homogeneous-wall (HW) pipes made of polyethylene (PE) or polypropylene (PP), -- structured-wall (SW) pipes of the corrugated double-wall type of construction as defined in Annex B,, whose structural layer(s) is (are) made of PE or PP, -- jointing of pipe lengths by means of butt fusion (HW) 1) or electrofusion (SW), -- fabricated and injection-moulded fittings made of PE, PP and poly(vinyl chloride) (PVC-U). NOTE The grouting procedure is outside the scope of this standard.

Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 2: Lining with continuous pipes; English version of DIN EN 13566-2:2006-02

LST EN 13566-2-2006 地下非压力排水和污水管网改造用塑料管道系统 第2部分：连续管道衬里

Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 2: Lining with continuous pipes

LST EN 14654-1-2006 排水沟和下水道清洁操作的管理和控制 第1部分：下水道清洁

Management and control of cleaning operations in drains and sewers - Part 1: Sewer cleaning