93.030 外部污水排放系统 标准查询与下载

BS EN 14758-1:2005 无压力地下排水和污水用塑料管道系统.含矿物调节剂的聚丙烯(PP-MD).第1部分:管、配件和系统用规范.

This European Standard specifies the requirements for solid-wall pipes, fittings and the system of piping systems made from mineral modified polypropylene materials (PP-MD) in the field of non-pressure underground drainage and sewerage outside the building structure (application area code "U"), and nonpressure underground drainage and sewerage for both buried in ground within the building structure (application area code "D") and outside the building structure. This is reflected in the marking of products by "U" and "UD". It also specifies the test parameters for the test methods referred to in this European Standard. This European Standard covers a range of nominal sizes, a range of pipe series/stiffness classes and gives recommendations concerning colours. NOTE 1 It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. In conjunction with Part 2 and Part 3 of EN 14758 (see Foreword) it is applicable to PP-MD pipes and fittings, their elastomeric sealing ring joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for non-pressure underground drainage and sewerage. This European Standard is applicable to PP-MD pipes with or without an integral socket. NOTE 2 The fittings can be manufactured by injection-moulding or be fabricated from pipes and/or mouldings. NOTE 3 Requirements and limiting values for application area code "D" are given in Table 4, Table 7 and Table 13. NOTE 4 Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex B can be used with pipes and fittings conforming to this European Standard, when they conform to the requirements for joint dimensions given in Clause 6 and to the requirements of Table 13.

Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings and the system

BS EN 14758-1+A1:2006 无压力地下排水和污水用塑料管道系统 含矿物调节剂的聚丙烯（PP-MD） 管、配件和系统用规范

Plastics piping systems for non-pressure underground drainage and sewerage. Polypropylene with mineral modifiers (PP-MD). Specifications for pipes, fittings and the system

BS PD CEN/TR 15128:2005 排水和污水系统的修复用欧洲标准的调查

This document gives a survey of European Standards available in the field of rehabilitation of drain and sewer systems.

Survey of European Standards for rehabilitation of drain and sewer systems

EN 14982:2006 热塑管道和导管系统.监测室和人孔用热塑性轴或升降管.环的硬度测定

This European Standard specifies a test method for assessing the initial (short-term) tangential ring stiffness of riser shafts for thermoplastics inspection chambers or manholes. NOTEThis is intended as a test of the structural integrity of riser shafts supporting product standards EN 13598-2 [1] and prEN 15229 [2].

Plastics piping and ducting systems - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of ring stiffness (Incorporates Amendment A1: 2010)

BS EN 14654-1:2005 排水沟和下水道清洁工作的管理和控制.下水道清洁

This European Standard specifies the general principles for the management and control of cleaning operations in drain and sewer systems and specifies requirements for implementation of cleaning programmes and for working practices. It is applicable to drain and sewers systems outside buildings, which operate essentially under gravity, from the point where the sewage leaves a building or roof drainage system, or enters a road gully, to the point where it is discharged into a treatment works or receiving water. Drains and sewers below buildings are included provided that they do not form part of the drainage system of the building.

Management and control of cleaning operations in drains and sewers - Sewer cleaning

NF P16-158-1:2005 排水沟和下水道清洁工作的管理和控制.第1部分:下水道清洁.

Management and control of cleaning operations in drains and sewers - Pat 1 : sewer cleaning.

DIN EN 14654-1:2005 排水沟和下水道清洁工作的管理和控制.第1部分:下水道清洁.德文版本 EN 14654-1-2005

This European Standard specifies the general principles for the management and control of cleaning operations in drain and sewer systems and specifies requirements for implementation of cleaning programmes and for working practices. It is applicable to drain and sewers systems outside buildings, which operate essentially under gravity, from the point where the sewage leaves a building or roof drainage system, or enters a road gully, to the point where it is discharged into a treatment works or receiving water. Drains and sewers below buildings are included provided that they do not form part of the drainage system of the building.

Management and control of cleaning operations in drains and sewers - Part 1: Sewer cleaning; English version of DIN EN 14654-1:2005

BS EN 14982+A1:2005 塑料管道系统 监测室和人孔用热塑柄和提升设备 环硬挺度的测定

Plastics piping and ducting systems. Thermoplastics shafts or risers for inspection chambers and manholes. Determination of ring stiffness

BS EN 14982:2006 塑料管道系统.监测室和人孔用热塑柄和提升设备.环硬挺度的测定

This European Standard specifies a test method for assessing the initial (short-term) tangential ring stiffness of riser shafts for thermoplastics inspection chambers or manholes. NOTE This is intended as a test of the structural integrity of riser shafts supporting product standards prEN 13598-2 and prEN 15229

Plastics piping and ducting systems — Thermoplastics shafts or risers for inspection chambers and manholes — Determination of ring stiffness

BS EN 14982:2006+A1:2010 塑料管道系统.监测室和人孔用热塑柄和提升设备.环硬挺度的测定

This European Standard specifies a test method for assessing the initial (short-term) tangential ring stiffness of riser shafts for thermoplastics inspection chambers or manholes.

Plastics piping and ducting systems. Thermoplastics shafts or risers for inspection chambers and manholes. Determination of ring stiffness

ANSI/ASTM F1867:2005 用做现有下水道和导管修复的A型折叠的/成形聚氯乙烯(PVC)管的安装规程

This practice covers the procedures for the rehabilitation of sewer lines and conduits 4 in. (102 mm) to 18 in. (457 mm) in diameter by the insertion of a folded/formed PVC pipe that is heated, pressurized, and expanded to conform to the wall of the original conduit forming a new structural pipe-within-a-pipe. This rehabilitation process can be used in a variety of gravity applications such as sanitary sewers, storm sewers, and process piping. This practice is to be used with the material specified in Section of Specification F 1871. The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are provided for information only. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. There is no similar or equivalent ISO Standard.

Practice for Installation of Folded/Formed Poly(Vinyl Chloride) (PVC) Pipe Type A for Existing Sewer and Conduit Rehabilitation

DS/EN 14654-1:2005 排水沟和下水道清洁操作的管理和控制 第1部分：下水道清洁

This European Standard specifies the general principles for the management and control of cleaning operations in drain and sewer systems and specifies requirements for implementation of cleaning programmes and for working practices.It is applicable to drain and sewers systems outside buildings, which operate essentially under gravity, from the point where the sewage leaves a building or roof drainage system, or enters a road gully, to the point where it is discharged into a treatment works or receiving water. Drains and sewers below buildings are included provided that they do not form part of the drainage system of the building.

Management and control of cleaning operations in drains and sewers - Part 1: Sewer cleaning

CAN/CSA-B66-2005 化粪池、预制滞留池的设计、构成材料和制造要求

1 Domaine d'application 1.1 Cette norme établit les exigences minimales en matière de conception et de matériaux, de méthodes de fabrication et de marquage des fosses septiques et des réservoirs de rétention préfabriqués, ainsi que des compartiments d'effluent faits en acier, en béton, en plastique renforcé de fibres de verre ou en polyéthylène, destinés à recevoir les eaux usées ou leur effluent. 1.2 Cette norme ne prétend pas aborder l'ensemble des questions de sécurité reliées à son utilisation. Il incombe donc à l'utilisateur d'établir les règles de santé et de sécurité appropriées, et de déterminer préalablement l'applicabilité des restrictions réglementaires afférentes. 1.3 L'annexe A illustre les aménagements caractéristiques des fosses septiques. Les figures de L'annexe A ne visent pas à proposer des matériaux, des méthodes ni des critères de conception. 1.4 Cette norme ne s'applique pas aux réservoirs de rétention destinés aux véhicules de camping. Ces exigences font l'objet de la CAN/CSA-B45.6. 1.5 Dans les normes CSA, le terme «doit» indique une exigence, c'est-à-dire une prescription que l'utilisateur doit respecter pour assurer la conformité à la norme; «devrait» indique une recommandation ou ce qu'il est conseillé mais non obligatoire de faire et «peut» une possibilité ou un conseil. Les notes qui accompagnent les articles ne comprennent pas de prescriptions ni de recommandations. Elles servent à séparer du texte les explications ou les renseignements qui ne font pas proprement partie de la norme. Les notes au bas des figures et des tableaux font partie de ceux-ci et peuvent être rédigées comme des prescriptions. Les annexes peuvent être normatives (obligatoires) ou informatives (facultatives).

Requirements for the design, constituent materials and manufacturing of septic tanks and prefabricated retention tanks

DS/CEN/TR 15128:2005 欧洲排水和下水道系统修复标准调查

This document gives a survey of European Standards available in the field of rehabilitation of drain and sewer systems.

Survey of European Standards for rehabilitation of drain and sewer systems

ANSI/ASTM D6783:2005 聚合物混凝土管规范

This specification covers polymer concrete pipe, 6 in. (150 mm) through 144 in. (3 660 mm), intended for use in gravity-flow systems for conveying sanitary sewage, storm water, and industrial wastes. Note 1 -There is no similar or equivalent ISO standard. Although this specification is suited primarily for pipe to be installed by direct burial and pipe jacking, it may be used to the extent applicable for other installations such as sliplining and rehabilitation of existing pipelines. Note 2 -Unlike reinforced thermosetting resin pipes, polymer concrete pipe is designed and installed using rigid pipe design theory and practices. The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. The following safety hazards caveat pertains only to the test methods portion, Section 8, of this specification. This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory req

Specification for Polymer Concrete Pipe

ANSI/ASTM D6783 REV A:2005 聚合物混凝土管标准规范

Standard Specification for Polymer Concrete Pipe

PD CEN/TR 15128:2005 排水和污水系统的修复用欧洲标准的调查

This document gives a survey of European Standards available inThe field of rehabilitation of drain and sewer systems.

Survey of European Standards for rehabilitation of drain and sewer systems

ASTM C1618-05 通过负（真空）或正气压力对混凝土卫生下水道管道的标准试验方法

This is a quality control test performed at the manufacturing plant to establish that the finished, shippable pipe meets the leakage limits stated in the specifications.1.1 This test method covers procedures for testing of precast concrete pipe sections, prior to delivery, where maximum field leakage rates are specified.1.2 Tests described in this standard are intended to be used at the point of manufacture of the concrete pipe and are not intended for testing installed pipe (for field tests see Practices C 924, C 969, and C 1214). The user of this specification is advised that individual or multiple pipe sections may be tested for the purpose of testing the pipe barrel and additionally the joints in straight alignment when multiple pipe sections are tested.1.3 The two leakage rates shown, which were used in calculating the test times, were chosen based on two generally accepted field air and vacuum test criteria. Test times are based on leakage rates and therefore are proportional only to the pipe diameter and are constant for any length of test pipe or pipeline.1.4 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.Note 18212;The availability of this test procedure for concrete pipe varies from location to location. Check with local supplier(s) for availability and recommendations.1.5 This standard does not purport to address all the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish the appropriate safety and health practices and to determine the applicability of regulatory limitations prior to its use. See Section 6 for specific safety precautions.

Standard Test Method for Concrete Sanitary Sewer Pipe by Negative (Vacuum) or Positive Air Pressure

DS/CEN/TR 14920:2005 排水管和下水道的抗喷射性 移动喷射试验方法

This document specifies a test method for the resistance to high pressure clean water jetting of pipes, fittings and joints used for drains and sewers. This test method is also applicable to components for renovation and replacement of drains and sewers.

Jetting resistance of drain and sewer pipes - Moving jet test method

PD CEN/TR 14920:2005 排水和排污管道的抗喷射能力.移动喷射试验法

Jetting resistance of drain and sewer pipes - Moving jet test method