93.060 隧道建筑 标准查询与下载

T/CECS 562-2018 《城市综合管廊防水工程技术规程》

本规程共分9章和2个附录，主要技术内容包括：总则、术语和符号、基本规定、混凝土结构自防水、明挖法现浇混凝土结构城市综合管廊、明挖法预制装配式混凝土结构城市综合管廊、矿山法城市综合管廊、盾构法城市综合管廊、顶管与箱涵顶进法城市综合管廊。

Technical specification for waterproofing of urban utility tunnel

DB37/T 5129-2018 隧道薄壁钢管初期支护施工技术规程

本规程适用于山东省行政区域内采用薄壁钢管混凝土作为初期支护的隧道构造设计、构建制作、施工和验收。

Technical specification for primary support construction of thin-walled steel pipes for tunnels

DB51/T 2515-2018 钢管混凝土桥梁焊接节点疲劳技术规程

本规程规定了钢管混凝土桥梁焊接节点总则、术语和符号、材料、连接类别与疲劳强度、荷载及疲劳应力幅、疲劳强度验算、构造与工艺、维护管理等内容。 本规程适用于圆形钢管混凝土桁式结构桥梁焊接节点和接头的疲劳设计。

Technical specification for fatigue of welded joints of concrete filled steel tube bridges

T/CDSA 305.16-2018 盾构维护高气压作业规程

盾构维护高气压作业与潜水施工作业性质非常相近，除作业环境不同外，均为在高气压下作业，进仓作业人员要呼吸与工作压力相等的高压气体。因此，在工作压力大于0.12MPa的压缩空气和工作压力更大（≥0.6MPa）的混合气盾构维护作业中，由经过高气压医学检查、培训及锻炼，适应高气压作业的潜水员或相应的工作人员来完成是十分必要的。在目前国内外尚无统一的作业标准情况下，在潜水行业内起草本规程，可以规范、指导盾构维护高气压作业，提高行业内此项操作的技能水平，为作业人员安全施工提供保障。 本规程适用于盾构高气压环境下换刀、焊接、切割和检测等维护作业，适用于呼吸压缩空气或混合气的盾构维护常规高气压作业。 盾构高气压下换刀、焊接、切割和检测等维护作业除应符合本规程规定之外，尚应符合国家现行有关标准的规定。

Operating regulations for tunnel boring machine maintenance under hyperbaric pressure

DB11/ 1444-2017 城市轨道交通隧道工程注浆技术规程

Technical specification for grouting in urban rail transit tunnel engineering

DB42/T 1237-2016 城市人行地下通道技术规程

Technical specification for urban pedestrian underpass

DB51/T 2243-2016 公路瓦斯隧道技术规程

本规程规定了公路瓦斯隧道分类标准、勘察方法、设计措施、施工措施及设备配置、揭煤防突措施、风险评估指标等。 本规程适用于公路瓦斯隧道勘察、设计、施工、运营管理、风险评估和质量检验与验收。

Technical specification for highway gas tunnel

GOST R 57208-2016 隧道和地铁. 检查与消除运行缺陷和损害的规则

Tunnels and subways. Rules of inspection and elimination of defects and damages under operation

DB34/T 2558-2015 高速公路施工标准化指南 隧道工程

本标准规定了高速公路隧道工程的术语和定义、总则、施工准备、洞口与明洞工程、洞身开挖、初期支护与辅助工程措施、仰拱与铺底、防水与排水、二次衬砌、小净距隧道与连拱隧道、辅助坑道和附属工程、隧道路面施工、超前地质预报与监控量测、安全生产与环境保护。 本标准适用于钻爆法开挖为主的安徽省新建、改建、扩建高速公路隧道施工，一级公路及其它等级公路隧道施工可参照执行。

Standardization Guidelines for Expressway Construction Tunnel Engineering

GOST R 56521-2015 道路运输隧道. 安全要求

Road transport tunnels. Safety requirements

GOST R 56334-2015 公路隧道. 人工照明. 规范和设计方法

Road tunnels. Artificial lighting. Norms and design methods

GOST 33153-2014 一般用途汽车道路. 隧道投影. 通用要求

Automobile roads of general use. Projection of tunnels. General requirements

GOST 33154-2014 一般用途汽车道路. 隧道测量. 通用要求

Automobile roads of general use. Tunnel surveying. General requirements

DS/EN 16276:2013 公路隧道疏散照明

This European Standard specifies evacuation lighting in road tunnels longer than 500 m and with an AADT (Annual Average Daily Traffic) higher than 500 vehicles to facilitate the safe evacuation of vehicle occupants in evacuation situations such as fire. I

Evacuation Lighting in Road Tunnels

GSO BS 6164:2011 建筑行业隧道施工安全实施规范

This British Standard makes recommendations for and gives guidance on health and safety practices in shaft sinking and tunnelling. Guidance on health and safety in the maintenance, renovation and repair of shafts and tunnels is also included. The standard includes health and safety recommendations that are also relevant to cut-and-cover tunnelling and immersed tube tunnels. The recommendations are not specifically intended to apply to the construction of shafts or tunnels for the purpose of winning minerals. NOTE 1 The design, manufacture and use of plant and machinery are referred to only where safety considerations are affected. Various European Standards relating to the design of tunnel boring machines (TBMs) are currently in preparation. NOTE 2 A list of current legislation relating to tunnel construction is given in Annex A.

Code of practice for safety in tunnelling in the construction industry

DB35/T 1088-2011 海（水）底隧道工程质量检验评定标准 第2部分：机电工程

本标准规定了海（水）底隧道工程质量检验评定第2部分机电工程的一般规定、调光设施、轴流风机、母线槽、治超设施、视频检测、排水工程、泡沫喷淋等内容。 本标准适用福建省内的新建、改建海（水）底隧道机电工程质量的检验标准和评定标准。 本标准适用于海（水）底隧道工程施工单位、监理单位、建设单位、检测单位和质量监督机构对海(水）底隧道机电工程质量的管理、监督和检验评定。

Submarine (water) tunnel engineering quality inspection and evaluation standard part 2: mechanical and electrical engineering

DB35/T 1087-2011 海（水）底隧道工程质量检验评定标准 第1部分：土建工程

本标准规定了海（水）底隧道工程质量检验评定第1部分土建工程的术语、总则、工程质量评定、 隧道总体、洞口及明洞工程、洞身开挖、初期支护、二衬仰拱及填充层、防排水及管沟、二次衬砌、防火涂料、复合式路面工程、装饰工程等内容。 本标准适用福建省内采用钻爆法施工的新建、改建海（水）底隧道土建工程质量的检验标准和评定标准。 本标准可用于海（水）底隧道工程施工单位、监理单位、建设单位、检测单位和质量监督机构对海(水）底隧道土建工程质量的管理、监督和检验评定。

Quality Inspection and Evaluation Standards for Sea (Water) Submarine Tunnel Engineering Part 1: Civil Engineering

DB35/T 1067-2010 公路隧道监控量测技术规程

本标准规定了公路隧道监控量测技术的术语和符号、技术要求、监控量测方法、监控量测数据处理与反馈、监控量测验收资料。 本标准适用于采用钻爆法修建的公路隧道，采用其他工法施工的隧道工程监控量测可参照执行。

Technical Regulations for Monitoring and Measurement of Highway Tunnels

DS/EN 12111+A1:2009 隧道掘进机 掘进机、连采机和冲击式裂土机 安全要求

Description of the machineThis European Standard specifies all significant hazards, hazardous situations and events relevant to road headers, continuous miners and impact rippers, when they are used as intended and under the conditions foreseen by the manufacturer (see clause 4). This standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards. This European Standard is applicable to road headers, continuous miners and impact rippers used in tunnelling and underground mining.Certain associated matters are not included in the scope of this standard:- the supply of electricity up to the machine;- the

Tunnelling machines - Road headers, continuous miners and impact rippers - Safety requirements

DS/EN 12336+A1:2008 隧道掘进机 盾构机、推力钻孔机、螺旋钻孔机、衬砌安装设备 安全要求

1.1 Description of the machinesThis European Standard is applicable to all types of shield machines and associated back up equipment, thrust boring machines, auger boring machines and lining erection equipment. It specifies the essential safety requirements for the design, installation, maintenance, and information for use of such machines.Shield machines and associated back up equipment include:- open shields for both manual and mechanical excavation;- shielded tunnel boring machines;- micro tunnelling machines;- towed or stationary back up equipment;- pipe jacking equipment.All shield machines provide lateral and radial ground support. In addition they ma

Tunnelling machines - Shield machines, thrust boring machines, auger boring machines, lining erection equipment - Safety requirements