93.080.20 道路建筑材料 标准查询与下载

prEN 12272-3-2021 表面修整 试验方法 第3部分：通过 Vialit 板冲击试验法测定粘合剂聚集体的附着力

Surface dressing - Test methods - Part 3: Determination of binder aggregate adhesivity by the Vialit plate shock test method

T/CSRA 5-2021 冷铺型路面防滑涂料技术要求

本标准规定了冷铺型路面防滑涂料的术语和定义、分类和组成、技术要求、试验方法、检验规则及标志、包装、运输和贮存。 本标准适用于公路上涂铺的冷铺型路面防滑涂料的生产、检验和使用。城市道路、机场、港口、厂矿等场所涂铺的冷铺型路面防滑涂料可参照执行。

Technical requirements for anti-skid coatings for cold paved pavement

PN-EN 12697-42-2021-06 E 沥青混合料 试验方法 第42部分：再生沥青中的异物量

Bituminous mixtures -- Test methods -- Part 42: Amount of foreign matter in reclaimed asphalt

DB62/T 4340-2021 公路沥青路面精表处技术规范

Technical specification for surface finish of highway asphalt pavement

ASTM D6373-21a 性能分级沥青粘合剂的标准规范

1.1 This specification2 covers asphalt binders graded by performance. Grading designations are related to the LTPPBind calculated maximum pavement design temperature and the minimum pavement design temperature. This specification contains Tables 1 and 2. Table 2 incorporates Practice D6816 for determining the critical low cracking temperature using a combination of Test Method D6648 and Test Method D6723 test procedures. If no table is specified, the default is Table 1. NOTE 1—For more information on LTPPBind online, see https:// infopave.fhwa.dot.gov/Tools/LTPPBindOnline accessed June 10, 2020. NOTE 2—For asphalt cements graded by penetration at 25 °C, see Specification D946/D946M. For asphalt cements graded by viscosity at 60 °C, see Specification D3381/D3381M. NOTE 3—AASHTO R 29 provides non-mandatory information for determining the performance grade of an asphalt binder. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Performance-Graded Asphalt Binder

ASTM D8239-21a 使用多重应力蠕变和恢复（MSCR）试验的性能分级沥青粘合剂的标准规范

1.1 This specification2 covers asphalt binders graded by performance. Grading designations are related to the LTPPBind calculated maximum pavement design temperature, the minimum pavement design temperature, and the traffic loading. NOTE 1—For more information on LTPPBind online, see https:// infopave.fhwa.dot.gov/Tools/LTPPBindOnline accessed June 10, 2020. 1.2 This specification incorporates Test Method D7405 for determining non-recoverable creep compliance, Jnr. “S,” “H,” “V,” or “E” designations must be specified for standard, heavy, very heavy, and extremely heavy traffic loading, respectively. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. NOTE 2—A guidance document for specifying bodies using R % for elastic properties is under development. NOTE 3—For asphalt binders graded by penetration at 25 °C, see Specification D946/D946M. For asphalt binders graded by viscosity at 60 °C, see Specification D3381/D3381M. For performance-graded asphalt binder, see Specification D6373. NOTE 4—AASHTO R 29 provides non-mandatory information for determining the performance grade of an asphalt binder. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Performance-Graded Asphalt Binder Using the Multiple Stress Creep and Recovery (MSCR) Test

ASTM C1791-16(2021) 新单位路面系统降低泡沫电位的标准指南

1.1 This guide covers methods for reducing efflorescence potential in new unit pavement systems. 1.2 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Reduction of Efflorescence Potential in New Unit Pavement Systems

ASTM C936/C936M-21 实心混凝土联锁铺路装置的标准规范

1.1?This specification covers the requirements for interlocking concrete pavers manufactured for the construction of paved surfaces. 1.2?Concrete units covered by this specification shall be made with lightweight or normal weight aggregates or both. Note 1:?If particular featur

Standard Specification for Solid Concrete Interlocking Paving Units

prEN 12697-43-2021 沥青混合料 试验方法 第43部分：耐燃料性

Bituminous mixtures - Test methods - Part 43: Resistance to fuel

DB37/T 5188-2021 城市道路泡沫温拌沥青混合料施工技术规程

本规程适用于山东省范围内城市道路泡沫温拌沥青混合料的设计、施工和质量检验。

Technical specification for urban road foam warm mix asphalt mixture construction

DB53/T 1043-2021 复合矿物掺合料在混凝土中应用技术规程

Technical specification for the application of composite mineral admixtures in concrete

T/QGCML 135-2021 生物基冷拌用高性能沥青再生剂

本文件规定了生物基冷拌用高性能沥青再生剂的术语和定义、分类和适用范围、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本文件适用于冷拌用再生乳化沥青和乳化沥青冷再生混合料的生产、检验和使用，非本文件规格产品及类似产品可参照执行。

Bio-based high-performance asphalt rejuvenator for cold mix

DB14/T 2282-2021 高模量抗疲劳沥青混合料设计与施工技术规范

本文件规定了高模量抗疲劳沥青混合料的原材料要求、配合比设计、施工工艺和施工质量控制与检查验收。 本文件适用于各等级公路工程新建或改（扩）建沥青路面，其他道路沥青路面可参照执行

Technical specification for design and construction of high modulus anti-fatigue asphalt mixture

DS/EN 1463-2:2021 道路标线材料《反光路钉》第2部分：道路试验性能规范

Road marking materials – Retroreflecting road studs – Part 2: Road test performance specifications

BS EN 1463-2:2021 道路标记材料 反光道路柱 道路试验性能规范

Road marking materials. Retroreflecting road studs. Road test performance specifications

PN-EN 1824-2021-05 E 道路标线材料 道路试验

Road marking materials -- Road trials

ASTM D5893/D5893M-16(2021) 用于波特兰水泥混凝土路面的冷应用 单组分 化学固化硅酮接头密封胶的标准规范

1.1 This specification covers cold-applied, singlecomponent, chemically curing silicone sealants that are based on polymers of polysiloxane structures and are intended for use in sealing joints and cracks in portland cement concrete highway and airfield pavements. The specification includes both non-sag and self-leveling types of sealants. 1.1.1 This specification does not purport to cover the properties required of sealants for use in areas of portland cement concrete pavements subject to jet fuel or other fuel spillage, such as vehicle or aircraft refueling and maintenance areas, or a combination thereof. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 The following safety hazards caveat pertains only to the test methods portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Appendix X1. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Cold-Applied, Single-Component, Chemically Curing Silicone Joint Sealant for Portland Cement Concrete Pavements

ASTM D6932/D6932M-21 露天级配摩擦层植物沥青混合料的材料和结构的标准指南

1.1?This guide covers the construction of open-graded friction course (OGFC) plant asphalt mixtures. End-use specifications should be adopted to conform to job and user requirements. Where applicable, Specification D3666 should be applied as a minimum for agencies testing and in

Standard Guide for Materials and Construction of Open-Graded Friction Course Plant Asphalt Mixtures

ASTM D5078/D5078M-11(2021) 沥青混凝土和波特兰水泥混凝土路面热裂缝填料标准规范

1.1 This specification covers hot-applied crack filler for use in filling cracks in asphalt concrete and portland cement concrete pavements. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Crack Filler, Hot-Applied, for Asphalt Concrete and Portland Cement Concrete Pavements

ASTM D6690-21 混凝土和沥青路面热应用接头和裂缝密封胶标准规范

1.1?This specification covers joint and crack sealants of the hot-applied type intended for use in sealing joints and cracks in portland cement concrete and asphaltic concrete pavements. 1.2?This specification does not purport to cover the properties required of sealants for us

Standard Specification for Joint and Crack Sealants, Hot Applied, for Concrete and Asphalt Pavements