93.080.20 道路建筑材料 标准查询与下载

ASTM D7196-18 冷拌乳化沥青样品的剥离试验的标准试验方法

1.1 This test method measures the resistance to raveling characteristics of emulsified asphalt and field aggregates or recycled asphalt pavement (RAP) mixtures by simulating an abrasion similar to early return to traffic. 1.2 A precision and bias statement for this standard has not been developed at this time. Therefore, this standard should not be used for acceptance or rejection of a material for purchasing purposes. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Raveling Test of Cold-Mixed Emulsified Asphalt Samples

ASTM D3381/D3381M-18 路面施工用粘度分级沥青粘合剂的标准规范

1.1 This specification covers asphalt binders graded by viscosity at 60 °C [140 °F] for use in pavement construction. Four sets of limits are offered in this specification. The purchaser shall specify the applicable table of limits. In the event the purchaser does not specify limits, Table 1 shall apply. For asphalt binders graded by penetration at 25 °C [77 °F], see Specification D946/D946M. If needed, volume corrections for asphalt binders should be made according to Practice D4311/ D4311M. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Viscosity-Graded Asphalt Binder for Use in Pavement Construction

ASTM D6933-18 乳化沥青中超大颗粒的标准试验方法（筛分试验）

Standard Test Method for Oversized Particles in Emulsified Asphalts (Sieve Test)

18/30382612 DC BS EN 12802 道路标记材料 实验室鉴定方法

BS EN 12802. Road marking materials. Laboratory methods for identification

ASTM D8239-18 使用多重应力蠕变和恢复（MSCR）试验的性能分级沥青粘合剂的标准规范

Standard Specification for Performance-Graded Asphalt Binder Using the Multiple Stress Creep and Recovery (MSCR) Test

ASTM D8237-18 用四点梁疲劳装置测定沥青集料混合物疲劳破坏的标准试验方法

Standard Test Method for Determining Fatigue Failure of Asphalt-Aggregate Mixtures With the Four-Point Beam Fatigue Device

T/ZS 0013-2018 村镇道路混凝土路面施工与验收规范

前  言　 1  范围　 2  规范性引用文件　 3  术语和定义　 4  基本要求　 5  水泥混凝土路面施工 5.1  施工前的准备　 5.2  混凝土的拌和及运送　 5.3  混凝土的摊铺与振捣　 5.4  表面整修和洒水养护 5.5  混凝土切缝　 5.6  拆模及填缝 5.7  不同季节混凝土施工要点 5.8  安全生产　 5.9  混凝土路面病害维修与养护　 6  工程质量控制与管理　 6.1  工程质量控制 6.2  混凝土路面直观质量检查及验收标准　 附录A（参考性附录）水泥凝固时间与温度的关系　

Code for construction and acceptance of concrete pavement for roads in villages and towns

T/ZS 0008-2018 彩色沥青混凝土道路面层技术规程

前  言 1  范围 2  规范性引用文件 3  术语和定义 4  基本要求 5  材料 5.1  一般要求 5.2  沥青技术要求 5.3  粗集料 5.4  细集料 5.5  填料 5.6  颜料 5.7  彩色路面防护剂　 5.8  彩色雾封层材料　 5.9  温拌添加剂 5.10  沥青混凝土混合料配合比 5.11  彩色微表处混合料 6  设计 6.1  结构功能 6.2  色彩 8  施工 9  质量检查与验收 10  养护 附  录  A（规范性引用文件）彩色沥青色彩配制方法

Technical specification for colored asphalt concrete road surface

DB62/T 2917-2018 机制砂混凝土应用技术规程

Technical specification for the application of machine-made sand concrete

DB61/T 1175-2018 建筑垃圾再生材料公路应用设计规范

本标准规定了建筑垃圾再生材料 （ 以下简称 “ 再生材料 ” ） 用于公路工程中的地基处理 、 路基填筑 及路面基层 、 底基层和再生集料混凝土的设计要求 。 本标准适用于各等级新建 、 改 （ 扩 ） 建公路 ， 市政道路可参照执行 。

Code for design of highway application of construction waste recycled materials

DB14/T 1715-2018 公路沥青混合料用抗车辙剂技术要求及检测方法

本标准规定了公路沥青混合料用抗车辙剂的技术要求、试验方法和进场检验。本标准适用于公路沥青混合料用抗车辙剂的质量控制和检验。

Technical requirements and testing methods of anti-rutting agent for highway asphalt mixture

DB14/T 1716-2018 公路沥青路面集料生产质量控制技术规程

本标准适用于山西省新建、改扩建和养护工程沥青路面用集料的生产及质量控制

Technical specification for quality control of highway asphalt pavement aggregate production

DIN EN 13285:2018 未结合的混合物 规范；德文版 EN 13285:2018

This European Standard specifies requirements for unbound mixtures used for construction and maintenance of roads, airfields and other trafficked areas. This European Standard applies to unbound mixtures of natural, manufactured and recycled aggregates with an upper sieve size (D) from 5,6 mm to 90 mm and lower sieve size (d) = 0 at the point of delivery. NOTE 1 Mixtures with an upper sieve size (D) greater than 90 mm are not covered by this European Standard but may be specified in the place of use. NOTE 2 Water content of the mixture and the density of the installed layer are not specified mixture requirements. Both parameters are related to the control of the construction of the layer and are outside the scope of this European Standard. The aggregate requirements are defined with appropriate cross-reference to EN 13242. Use of aggregates as soil is not covered by this standard.

Unbound mixtures - Specifications; German version EN 13285:2018

DB12/T 821-2018 路用水性环氧改性乳化沥青防水涂料技术要求

本标准适用于各等级道路水泥混凝土基面上的防水粘结层

Technical requirements for water-based epoxy modified emulsified asphalt waterproof coatings for roads

DB12/T 822-2018 路用高粘结力环氧乳化沥青技术要求

本标准适用于各级道路结构层之间设置的粘结层。

High cohesion epoxy emulsified asphalt technical requirements for road

DB13/T 2853-2018 干法直投改性剂沥青路面施工技术规范

Technical specification for asphalt pavement construction by direct injection of dry method

NF P98-170:2018 混凝土路面 施工和控制

Le présent document se rapporte à la construction et au contrôle des couches en béton de ciment coulé en place.

Concrete pavements - Construction and controls

ASTM E1337-90(2018) 使用标准参考试验轮胎确定铺设表面的纵向峰值制动系数的标准测试方法

Standard Test Method for Determining Longitudinal Peak Braking Coefficient of Paved Surfaces Using Standard Reference Test Tire

ASTM D7538-09(2018) 使用雾化喷雾装置评估交通油漆的防水性能的标准做法

1.1 A newly applied traffic paint film may be exposed to rain of varying intensities shortly after application. Practice D7377 describes a practice for evaluating the water wash-off resistance of traffic paints to a hard rain using a steady stream of water from a faucet at a rate of approximately 5.7 L per min. Practice D7538 is a similar practice that describes the use of an adjustable nozzle atomizing spray device to deliver a spray of water that simulates rain rates from approximately 0.05 to 0.5 L per min. This test can be used to compare conventional and fast-dry traffic paints for their relative ability to withstand rain soon after application on roadway surfaces. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Evaluating the Water Wash-Off Resistance of Traffic Paints Using an Atomizing Spray Device

ASTM C936/C936M-18 实心混凝土联锁铺路单元标准规范

1.1 This specification covers the requirements for interlocking concrete pavers manufactured for the construction of paved surfaces. 1.2 When particular features are desired, such as weight classification, higher compressive strength, surface textures, finish, color, or other special features, such properties should be specified by the purchaser. Local sellers, however, should be consulted as to availability of units having the desired features. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Solid Concrete Interlocking Paving Units