97.120 家用自动控制装置 标准查询与下载

KS C 9806-2014(2019) 数字锁

Digital door locks

KS C 9806-2014 数码门锁

이 표준은 건축물의 출입문 등에 사용되며, 모터나 솔레노이드 등의 전기적 동작에 의해 직ㆍ간접적으로 동작되는 디지털 도어록의 제품 규격 및 시험방법에 대하여 규정한다.

Digital door locks

IEC 60730-2-22:2014 家用和类似用途电自动控制器. 第2-22部分: 热电机保护器的详细要求

"This clause of Part 12 is applicable except as follows: Replacement: This part of IEC 60730 applies to the partial evaluation of thermal motor protectors as defined in IEC 60730-1 for household and similar use@ including heating@ air conditioning and similar applications as well as for sealed (hermetic and semi-hermetic type) motorcompressors. NOTE A thermal motor protector is considered an integrated control since its protective functionality is dependent on the correct mounting and fixing in or on a motor and which can only be fully tested in combination with the relevant motor. This dependency is illustrated by: the ability of the thermal motor protector to accurately and reliably sense the heat of the motor windings; thus@ addressing the over-temperature protection due to motor overload conditions; the ability of the thermal motor protector to accurately and reliably sense the current due to motor lockedrotor conditions; thus@ reducing the response time and not being adversely affected by heat-sink at the assembly spot in the application; the influence of the motor's electromagnetic field on the switch behaviour of the thermal motor protector; particularly@ affecting the arc direction between the contacts resulting in uneven wear of the contact material and eventually leading to failure of operation. Requirements concerning the testing of the combination of sealed (hermetic and semihermetic type) motor-compressors and thermal motor protectors are given in IEC 60335-2-34. This standard applies to thermal motor protectors using NTC or PTC thermistors@ additional requirements for which are contained in Annex J. This standard applies to the inherent safety@ to the operating values@ operating times@ and operating sequences@ where such are associated with equipment safety@ and to the testing of thermal motor protectors used in or on household or similar equipment as well as sealed (hermetic and semi-hermetic type) motor-compressors. This standard applies to thermal motor protectors for appliances within@ but not limited to@ the scope of IEC 60335-1 and its Part 2's. NOTE Throughout this standard@ the word ""equipment"" means ""appliance and equipment"". Thermal motor protectors not intended for normal household use@ but which nevertheless may be used by the public@ such as equipment intended to be used by laymen in shops@ in light industry and on farms@ are within the scope of this standard. This standard does not apply to thermal motor protectors designed exclusively for industrial applications. This standard does not apply to other means of motor protection. This standard does not apply to a manual device for opening the circuit. 2 References to ""Part 1"" in this document pertain to the fourth edition of IEC 60730-1 published in 2010."

Automatic electrical controls for household and similar use - Part 2-22: Particular requirements thermal motor protectors

UL 60730-2-7-2014 家用和类似用途的自动电控制装置.第2部分:定时器和定时自动开关的特殊要求

UL Standard for Safety Automatic Electrical Controls for Household and Similar Use; Part 2: Particular Requirements for Timers and Time Switches (Second Edition; Reprint with revisions through and including July 31, 2014)

BS EN 50491-6-1:2014 家用和建筑物电子系统 (HBES) 和建筑物自动化和控制系统 (BACS) 的一般要求. 家用和建筑物电子系统安装. 安装和规划

General requirements for Home and Building Electronic Systems (HBES) and Building Automation and Control Systems (BACS). HBES installations. Installation and planning

KS C IEC 60730-2-18-2014 家用和类似用途自动电气控制装置第2部分 18：自动电气水流和空气流量传感控制装置的特殊要求，包括机械要求

Automatic electrical controls for household and similar use－Part 2－18：Particular requirements for automatic electrical water and air flow sensing controls, including mechanical requirements

KS C IEC 60730-2-18:2014 家用及类似用途的自动控制器 第2-18部分：流量控制装置的特殊要求

Automatic electrical controls for household and similar use－Part 2－18：Particular requirements for automatic electrical water and air flow sensing controls, including mechanical requirements

CAN/CSA-E60730-2-15-2014 家用和类似用途的自动电气控制器 第 2:15 部分：自动电气气流、水流和水位传感控制器的特殊要求（第一版）

Automatic electrical controls for household and similar use - Part 2:15: Particular requirements for automatic electrical air flow, water flow and water level sensing controls (First Edition)

GOST IEC 60730-2-6-2014 家用和类似用途电自动控制器. 第2-6部分. 包括机械要求的自动电压传感控制用特殊要求

Automatic electrical controls for household and similar use. Part 2-6. Particular requirements for automatic electrical pressure sensing controls including mechanical requirements

ANSI/UL 60730-2-5-2014 家用和类似用途的自动电气控制器标准.第2部分:电燃烧器控制器的详细要求

Standard for Safety for Automatic Electrical Controls for Household and Similar Use, Part 2: Particular Requirements for Automatic Electrical Burner Control Systems

JB/T 8592-2013 家用和类似用途电自动控制器 电磁四通换向阀

本标准规定了家用和类似用途电自动控制器电磁四通换向阀(以下简称为四通换向阀)的术语和定义、型号和参数及使用条件、技术要求、试验方法、检验规则、标志、包装、运输及贮存。本标准适用于额定电压为直流不超过240 V、交流不超过380 V、频率50 Hz或60 Hz,名义容量不大于210kW、使用制冷剂为R22、R134a、R407C、R410A等的热泵用四通换向阀。

Automatic electrical controls for household or similar use.4-way solenoid reversing valve

JB/T 10302-2013 家用和类似用途电自动控制器 小型制冷系统两通电磁阀

本标准规定了家用和类似用途制冷系统两通交流及直流电磁阀(以下简称电磁阀)的术语和定义、型式、型号和基本参数、技术要求、试验方法、检验规则、标志、包装、运输和贮存。本标准适用于交流电压不超过440 V、50 Hz或60 Hz,直流电压不超过320 V,制冷工质为R22、R134a、R502、R407C、R410A等,阀口通径不大于25 mm的家用和类似用途制冷系统中使用的两通电磁阀。

Automatic electrical controls for household or similar use.2-way solenoid valve in refrigerating system

JB/T 11720-2013 一体式电磁加热控制器

本标准规定了一体式电磁加热控制器(以下简称控制器)的术语和定义、分类、主要技术参数和型号命名、技术要求、试验方法、检验规则及标志、包装、运输和贮存。本标准适用于装在家用和类似用途的、带有通信接口,包含电磁能量转换装置,额定功率不超过3 000 W的电磁加热器具的控制器。本标准不适用于:--专门用于工业用途的一体式电磁加热控制器;--在易燃易爆环境下工作的一体式电磁加热控制器。

Integrated induction heating controls

JB/T 11721-2013 电自动控制器用液体膨胀式金属膜盒

本标准规定了电自动控制器用液体膨胀式金属膜盒(以下简称膜盒)的术语和定义、型号与基本参数、技术要求、试验方法、检验规则和标志、包装、运输及贮存。本标准适用于电自动控制器的和温度传感的且由金属制成的膜盒。

Liquid-filled metal diaphragm assembly for automatic electrical controls

UL 60730-2-11-2013 家用和类似用途的自动电控制装置.第2-11部分:能量调节器的详细要求

Automatic electrical controls for household and similar use - Part 2-11: Particular requirements for energy regulators

IEC 60730-1:2013 电自动控制器. 第1部分: 一般要求

"In general@ this part of IEC 60730 applies to automatic electrical controls for use in@ on@ or in association with equipment for household and similar use. The equipment may use electricity@ gas@ oil@ solid fuel@ solar thermal energy@ etc.@ or a combination thereof. NOTE 1 Throughout this standard the word ""equipment"" means ""appliance and equipment."" EXAMPLE 1 Controls for appliances within the scope of IEC 60335. This International Standard is applicable to controls for building automation within the scope of ISO 16484. This standard also applies to automatic electrical controls for equipment that may be used by the public@ such as equipment intended to be used in shops@ offices@ hospitals@ farms and commercial and industrial applications. EXAMPLE 2 Controls for commercial catering@ heating and air-conditioning equipment. This standard is also applicable to individual controls utilized as part of a control system or controls which are mechanically integral with multifunctional controls having non-electrical outputs. EXAMPLE 3 Independently mounted water valves@ controls in smart grid systems and controls for building automation systems within the scope of ISO 16484-2. This standard is also applicable to relays when used as controls for IEC 60335 appliances. Additional requirements for the safety and operating values of relays when used as controls for IEC 60335 appliances are contained in Annex U. NOTE 2 These requirements are referred to in the scope of IEC 61810-1. NOTE 3 This standard is intended to be used for the testing of any stand-alone relay which is intended to be used as a control of an appliance according to IEC 60335-1. It is not intended to be used for any other stand-alone relay@ or to replace the IEC 61810 series of standards. This standard does not apply to automatic electrical controls intended exclusively for industrial process applications unless explicitly mentioned in the relevant part 2 or the equipment standard. This International Standard applies to the inherent safety@ to the operating values@ operating times@ and operating sequences where such are associated with equipment safety@ and to the testing of automatic electrical control devices used in@ or in association with@ equipment. This standard applies to controls using thermistors@ see also Annex J. This standard is also applicable to the functional safety of low complexity safety related systems and controls. This standard applies to automatic electrical controls@ mechanically or electrically operated@ responsive to or controlling such characteristics as temperature@ pressure@ passage of time@ humidity@ light@ electrostatic effects@ flow@ or liquid level@ current@ voltage@ acceleration@ or combinations thereof. This standard applies to starting relays@ which are a specific type of automatic electrical control@ intended to switch the starting winding of a motor. Such controls may be built into@ or be separate from@ the motor. This standard applies to manual controls when such are electrically and/or mechanically integral with automatic controls. NOTE Requirements for manual switches not forming part of an automatic control are contained in IEC 61058-1. This standard applies to a.c. or d.c. powered controls with a rated voltage not exceeding 690 V a.c. or 600 V d.c. This standard does not take into account the response value of an automatic action of a control@ if such a response value is dependent upon the method of mounting the control in the equipment. Where a response value is of significant purpose for the protection of the user@ or surroundings@ the value defined in the appropriate household equipment standard or as determined by the manufacturer shall apply. This standard applies also to controls incorporating electronic devices@ requirements for which are contained in Annex H. This standard applies also to controls using NTC or PTC thermistors@ requirements for which are contained in Annex J."

Automatic electrical controls - Part 1: General requirements

IEC 60730-2-5:2013 家用和类似用途的电气自动控制器 第2-5部分:燃烧器电气自动控制系统的详细要求

"Scope and normative references This clause of Part 1 is applicable except as follows: Replacement: This part of IEC 60730 applies to automatic electrical burner control systems for the automatic control of burners for oil@ gas@ coal or other combustibles for household and similar use including heating@ air conditioning and similar use. This part 2-5 is applicable to a complete burner control system and to a separate programming unit. This part 2-5 is also applicable to a separate electronic high-voltage ignition source and to a separate flame detector. NOTE Separate ignition devices (electrodes@ pilot burners@ etc.) are not covered by this part 2-5 unless they are submitted as part of a burner control system. Requirements for separate ignition transformers are contained in IEC 60989. Throughout this part 2-5@ where it can be used unambiguously@ the word ""system"" means ""burner control system"" and ""systems"" means ""burner control systems"". Systems utilizing thermoelectric flame supervision are not covered by this part 2-5. This part 2-5 applies to the inherent safety@ to the manufacturer's declared operating values@ operating times and operating sequences where such are associated with burner safety and to the testing of automatic electrical burner control systems used in@ on@ or in association with@ burners. NOTE Requirements for specific operating values@ operating times and operating sequences are given in the standards for appliances and equipment. Systems for equipment not intended for normal household use@ but which nevertheless may be used by the public@ such as equipment intended to be used by laymen in shops@ in light industry and on farms@ are within the scope of this part 2-5. This part 2-5 applies to systems using NTC or PTC thermistors@ additional requirements for which are contained in Annex J. This part 2-5 does not apply to systems designed exclusively for industrial applications. This part 2-5 applies to manual controls when such are electrically and/or mechanically integral with automatic controls. NOTE Requirements for manual switches not forming part of an automatic control are contained in IEC 61058-1. Throughout this part 2-5@ the word ""equipment"" means ""appliance and equipment"". Replacement: This part 2-5 applies to systems with a rated voltage not exceeding 660 V and with a rated current not exceeding 63 A. Replacement: This part 2-5 does not take into account the response value of an automatic action of a control@ if such a response value is dependent upon the method of mounting the control in the equipment. Where a response value is of significant purpose for the protection of the user@ or surroundings@ the value defined in the appropriate household equipment standard or as determined by the manufacturer applies. NOTE This part 2-5 includes systems responsive to flame properties. Replacement: This part 2-5 applies also to systems incorporating electronic devices@ requirements for which are contained in Annex H."

Automatic electrical controls - Part 2-5: Particular requirements for automatic electrical burner control systems

QB/T 4495-2013 家用和类似用途集成式多功能吊顶装置安装技术要求

本标准规定了家用和类似用途集成式多功能吊顶装置(简称“多功能吊顶装置”)的术语和定义、功能模块、吊顶模块和安装附件要求、安装条件、安装要求、安装试验方法、安装检查与验收,以及专业安装人员的资质要求。本标准适用于多功能吊顶装置的安装。

Mounting technical requirements for household and similar integrated multi-functional ceiling appliances

QB/T 2263-2013 房间空气调节器电子控制器

本标准规定了房间空气调节器电子控制器的术语和定义、要求、试验方法、检验规则、标志、包装、运输和贮存。本标准适用于GB/T 7725中规定的房间空气调节器所使用的电子控制器(以下简称“电子控制器”)。

Electronic controls for room air conditioners

NF C47-739:2013 家用和类似用途电气自动控制器.第2-9部分:温度敏感控制器的详细要求

Automatic electrical controls for household and similar use - Part 2-9 : particular requirements for temperature sensing controls