97.150 铺地非织物 标准查询与下载

BS EN 1081:2018+A1:2020 弹性层压板和模块化多层地板覆盖物 电阻的测定

What is BS EN 1081 about?    BS EN 1081 specifies test methods for determining the vertical resistance, the resistance to earth, the surface resistance of a resilient, laminate, and modular multilayer floor covering after installation in the test piece or after installation.   Who is BS EN 1081 for?   BS EN 1081 on r esilient, laminate, and modular multilayer floor coverings is useful for:  

Resilient, laminate and modular multilayer floor coverings. Determination of the electrical resistance

ISO 10874:2009/Amd 1:2020 消除第22类+

Resilient, textile and laminate floor coverings — Classification — Amendment 1: Elimination of class 22+

EN ISO 20326:2018/A1:2020 要求取决于基板 包含修改件A1,2020

Resilient floor coverings - Specification for floor panels/assembly for loose laying - Amendment 1: Requirements depending on the substrate (ISO 20326:2016/Amd 1:2020)

ISO 20326:2016/Amd 1:2020 要求取决于基板

Resilient floor coverings — Specification for floor panels/assembly for loose laying — Amendment 1: Requirements depending on the substrate

BS ISO 8543:2020 纺织地板覆盖物 质量测定方法

1   Scope This document specifies methods for the determination of the total mass per unit area, total pile mass per unit area , and mass of pile per unit area above the substrate, and for the calculation of measured surface pile density and measured pile fibre volume ratio of textile floor coverings.

Textile floor coverings. Methods for determination of mass

BS ISO 1763:2020 纺织地板覆盖物 测定每单位长度和每单位面积的簇绒和/或毛圈数量

What is ISO 1763 about? ISO 1763 discusses textile floor coverings ISO 1763 specifies a method for the determination of the number of tufts and/or loops per unit length and per unit area of a textile floor covering. ISO 1763 specifies test methods, specimens, and procedures to measure the distance between tufts and loops per unit length. Note: ISO 1763 is applicable to textile floor coverings with the pile of which consists of tufts and/or loops. Who is ISO 1763 for? ISO 1763 on textile floor coverings is useful for: Floor coverings producers Floor coverings installers Quality control laboratories Why should you use ISO 1763 ? ISO 1763 specifies a method for the determination of the number of tufts and/or loops per unit length and per unit area of a textile floor covering which helps you to understand the form of construction. ISO 1763 provides a method for the determination of the number of tufts and/or loops per unit length and per unit area of a textile floor covering. While textiles on floors feel good and make rooms stylish and comfortable, ISO 1763

Textile floor coverings. Determination of number of tufts and/or loops per unit length and per unit area

ISO 1763:2020 铺地织物.单位长度和单位面积簇和/或圈数的测定

This document specifies a method for the determination of the number of tufts and/or loops per unit length and per unit area of a textile floor covering. It is applicable to textile floor coverings with the pile of which consists of tufts and/or loops.

Textile floor coverings — Determination of number of tufts and/or loops per unit length and per unit area

ASTM D6004-20 测定弹性地板和地毯粘合剂粘合剪切强度的标准试验方法

Standard Test Method for Determining Adhesive Shear Strength of Resilient Flooring and Carpet Adhesives

ASTM F925-13(2020) 弹性地板耐化学品的标准试验方法

1.1 This test method provides a procedure for determining the resistance of resilient floor covering to surface deterioration when exposed to various chemical reagents. This test method is not intended as a staining test nor as a method to judge surface and appearance restoration of the sample after exposure to the chemical reagent. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazard information is provided in Section 6 of this test method. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Resistance to Chemicals of Resilient Flooring

BS EN 17396:2020 弹性地板覆盖物 石英乙烯基瓷砖 规格

What is BS EN 17396 about? BS EN 17396 discusses floor tiles. BS EN 17396 specifies the characteristics of homogeneous quartz vinyl tiles based on polyvinyl chloride binder, quartz sand as a sole or partial filler, with or without a transparent, non-PVC factory finish and supplied in tile form. To encourage the consumer to make an informed choice, BS EN 17396 includes a classification system based on the intensity of use, which shows where these floor coverings will give satisfactory service also specifies requirements for marking. Who is BS EN 17396 for? BS EN 17396 on quartz vinyl tiles is useful for: Tiles manufacturers and suppliers Quality control laboratories Civil engineers Floor decorator End users Why should you use BS EN 17396 ? Quartz vinyl tiles are made of 1 single layer that offers vibrancy and depth of colour.  Quartz vinyl tiles are incredibly durable and stain-resistant which makes them the best flooring choice for heavy traffic areas. BS EN 17396 specifies a classification system that shows where these resilient floor coverings will give quality service. BS EN 17396 helps you with the installation of resilien...

Resilient floor coverings. Quartz vinyl tiles. Specification

BS EN ISO 12951:2020 纺织地板覆盖物 使用 Lisson Tretrad 机器测定质量损失、纤维结合和楼梯前缘外观变化

What is ISO 12951 about?    ISO 12951 discusses determination methods of textile floor coverings. ISO 12951 specifies four methods of testing for textile floor coverings (with or without an underlay) using the Lisson Tretrad machine.   Test A: determination of mass loss of textile floor coverings, also used to assess fibre bind of synthetic pile carpets   Test B: determination of stair nosing appearance change of textile floor coverings  

Textile floor coverings. Determination of mass loss, fibre bind and stair nosing appearance change using the Lisson Tretrad machine

EN ISO 12951:2020 纺织地板覆盖物.使用Lisson踏轮机质量损失,纤维结合和楼梯防滑外观变化的测定

This document specifies four methods of test for textile floor coverings (with or without an underlay, see Clause 9) using the Lisson Tretrad machine. — test A: determination of mass loss of textile floor coverings, also used to assess fibre bind of synthetic pile carpets; — test B: determination of stair nosing appearance change of textile floor coverings; — test C: determination of fibre bind on synthetic loop pile carpets; — test D: determination of fibre bind (hairiness) on needled floor coverings and floor coverings without pile.

Textile floor coverings - Determination of mass loss, fibre bind and stair nosing appearance change using the Lisson Tretrad machine (ISO 12951:2020)

ISO 18167:2020 纺织地板 - 安装实践 - 一般

This document sets out the requirements for installing textile floor coverings (carpets). It gives details of the work necessary in preparing subfloor surfaces together with the procedures that are to be adopted where textile floor coverings are laid over various types of subfloors and underlays and where subfloor heating units are installed. NOTE This document addresses needle insertion tufted, woven, fusion bonded, fibre bonded, knitted, non- woven, felted, and flocked textile floor coverings.

Textile floor coverings — Installation practices — General

ISO 8543:2020 纺织地板覆层 - 质量测定方法

This document specifies methods for the determination of the total mass per unit area, total pile mass per unit area, and mass of pile per unit area above the substrate, and for the calculation of measured surface pile density and measured pile fibre volume ratio of textile floor coverings.

Textile floor coverings — Methods for determination of mass

BS EN 1816:2020 弹性地板覆盖物 带泡沫背衬的均质和异质光滑橡胶地板覆盖物规范

What is BS EN 1816   about? BS EN 1816   specifies the characteristics of homogeneous and heterogeneous smooth (including grained or embossed) rubber floor coverings with foam backing, supplied in roll or tile form. BS EN 1816   includes a classification system based on the intensity of use, which shows where these resilient floor coverings will give satisfactory service.   BS EN 1816   specifies requirements for marking. Who is BS EN 1816 for? BS EN 1816   on homogeneous and heterogeneous smooth rubber floor coverings is useful for: Floor coverings producers Floor cover installers Quality control laboratories End users Why should you use BS EN 1816 ? BS EN 1816   specifies characteristics of homogeneous and heterogeneous smooth (including grained or embossed) rubber floor coverings with foam backing, supplied in roll or in tile form for manufacturing which helps you to offer an enormous quality range of smooth rubber flooring covers to consumers.

Resilient floor coverings. Specification for homogeneous and heterogeneous smooth rubber floor coverings with foam backing

BS EN 1817:2020 弹性地板覆盖物 均质和异质光滑橡胶地板覆盖物规范

What is BS EN 1817 about? BS EN 1817   discusses resilient floor coverings.   BS EN 1817   specifies the characteristics of homogeneous and heterogeneous smooth (including grained or embossed) rubber floor coverings, supplied in either tile or roll form. BS EN 1817   includes a classification system based on the intensity of use, which shows where these resilient floor coverings should give satisfactory service.   BS EN 1817   specifies requirements for marking. Who is BS EN 1817 for? BS EN 1817   on homogeneous and heterogeneous smooth rubber floor coverings is useful for: Floor coverings producers Floor cover installers Quality control laboratories End users Why should you use BS EN 1817 ? BS EN 1817   specifies characteristics of homogeneous and heterogeneous smooth (including grained or embossed) rubber floor coverings, supplied in roll or in tile form for manufacturing which helps you to offer an enormous quality range of smooth rubber flooring covers to consumers...

Resilient floor coverings. Specification for homogeneous and heterogeneous smooth rubber floor coverings

BS ISO 2551:2020 纺织地板覆盖物和瓷砖形式的纺织地板覆盖物 确定由于不同的水和热条件以及平面外变形的影响而引起的尺寸变化

What is ISO 2551 about? ISO 2551 discusses the determination of dimensional changes of textile floor coverings and textile floor coverings in tile form. ISO 2551 specifies a procedure for the determination of dimensional changes and distortion out of plane likely to take place when textile floor coverings and tiles are subjected to varied water and heat conditions. Note: The method is applicable to all textile floor coverings and textile floor coverings in tile form. Who is ISO 2551 for? ISO 2551 on the determination of dimensional changes of textile floor coverings is useful for: Floor covering producers Installers Quality control department Service providers Why should you use ISO 2551 ? Textile floor coverings and textile floor coverings in tile form in the home have always had a practical and/or decorative use and add the finishing touches to a room. ISO 2551 was developed to standardize and assess the intrinsic dimensional stability of the textile floor coverings and textile floor coverings tile without the aid of adhesives. ISO 2551 specifies a method for the determination of dimensional changes due to the effects of varied water and heat conditions an...

Textile floor coverings and textile floor coverings in tile form. Determination of dimensional changes due to the effects of varied water and heat conditions and distortion out of plane

ISO 12951:2020 纺织地板 - 使用Lisson Tretrad机器测定质量损失 纤维束和楼梯外观变化

This document specifies four methods of test for textile floor coverings (with or without an underlay, see Clause 9) using the Lisson Tretrad machine. — test A: determination of mass loss of textile floor coverings, also used to assess fibre bind of synthetic pile carpets; — test B: determination of stair nosing appearance change of textile floor coverings; — test C: determination of fibre bind on synthetic loop pile carpets; — test D: determination of fibre bind (hairiness) on needled floor coverings and floor coverings without pile.

Textile floor coverings — Determination of mass loss, fibre bind and stair nosing appearance change using the Lisson Tretrad machine

ISO 2551:2020 瓷砖形式的铺地织物和铺地织物.因不同水和热条件的影响和平面外变形引起的尺寸变化的测定

This document specifies a procedure for the determination of the dimensional changes and distortion out of plane likely to take place when textile floor coverings and tiles are subjected to varied water and heat conditions. The method is applicable to all textile floor coverings and textile floor coverings in tile form.

Textile floor coverings and textile floor coverings in tile form — Determination of dimensional changes due to the effects of varied water and heat conditions and distortion out of plane

ASTM F510/F510M-20 使用磨粒机进行耐磨性的标准试验方法

1.1 This test method2 describes a laboratory procedure for determining the abrasion resistance of resilient flooring using an abrader with a grit feeder.3 1.2 The equipment used in this test method is a modification of the Taber abraser. The regular abrading wheels are replaced by leather clad brass wheels (rollers). As the specimen holder rotates, a grit-feeding device dispenses aluminum oxide grit onto the specimen before the grit passes under the leather clad brass wheels. As the specimen rotates, the rub-wear action of the wheels and abrasive grit causes abrasion on the test piece. Using the vacuum system incorporated in the apparatus, the used grit and abraded material are removed after passing under both wheels. 1.3 This test method employs a rotary, rubbing action caused by loose abrasive grit and the two abrading wheels. One wheel rubs the specimen from the center outward and the other from the outside toward the center. The wheels traverse a complete circle and have an abrasive action on the rotating specimen at all angles. This action approaches the twisting action between shoe and floor that occurs when a person turns. The use of loose grit serves the function of an abradant and also aids in the rolling action characteristic of normal walking. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Resistance to Abrasion of Resilient Floor Coverings Using an Abrader with a Grit Feed Method