97.150 铺地非织物 标准查询与下载

BS EN ISO 23999:2018 弹性地板覆盖物 暴露于热环境后尺寸稳定性和卷缩的测定

Resilient floor coverings. Determination of dimensional stability and curling after exposure to heat

ASTM G219-18 用斜面试验装置测定试验偶件静摩擦系数的标准指南

1.1 This guide is intended to standardize the use of an inclined plane testing device to measure the breakaway friction (static) coefficient of mating couples that are of such size and shape that they can be made into a rider (one member of the sliding couple) on a flat surface (the second member of the sliding couple) that can be inclined at an angle to produce motion of the rider. The tangent of the angle at which breakaway motion of the rider occurs on the angled plane is the breakaway or static coefficient of friction for that sliding couple. 1.2 Units—The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Determination of Static Coefficient of Friction of Test Couples Using an Inclined Plane Testing Device

EN ISO 23999:2018 弹性覆地材料.热暴露尺寸稳定性和卷曲测定

Resilient floor coverings - Determination of dimensional stability and curling after exposure to heat

ASTM F3010-18 双组分树脂基膜成型减水剂在弹性地板下使用的标准实践

1.1 This practice covers the properties, application, and performance of a two-component resin based membraneforming moisture mitigation system to high moisture concrete substrates prior to the installation of resilient flooring. 1.2 This practice includes recommendations for the preparation of the concrete surface to receive a two-component resin based membrane-forming moisture mitigation system. 1.3 This practice does not supersede written instructions of the two-component resin based membrane-forming moisture mitigation system manufacturer, the resilient flooring manufacturer, underlayment manufacturer, the adhesive manufacturer, or other components of the finish flooring system, or combinations thereof. Users of this practice shall review manufacturer’s technical data sheets and installation instructions for compatibility of system components. 1.4 The following membrane-forming or non membraneforming moisture mitigation systems are not included in the scope of this practice: 1.4.1 Moisture mitigation systems that chemically react with any constituent of the concrete to form a gel or crystalline substance within the concrete. 1.4.2 Penetrating, wateror solvent-based compounds that do not form a continuous membrane on the concrete surface. 1.4.3 Water-based membrane-forming moisture mitigation systems are not included in the scope of this document. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Two-Component Resin Based Membrane-Forming Moisture Mitigation Systems for Use Under Resilient Floor Coverings

ASTM D6859-18 成层绒线地板覆盖物的绒头厚度的标准试验方法

1.1 This test method covers the determination of pile thickness of finished level pile yarn floor covering using a thickness measuring instrument having a stationary surface (platen), a circular pressure foot under specified force, and capable of being moved vertically above the platen. 1.2 This test method is applicable only to finished level loop, cutpile and cut & loop constructions with tuft heights less than 0.25 in. (6 mm). 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Pile Thickness of Finished Level Pile Yarn Floor Coverings

ISO 23999:2018 弹性地板覆盖物.暴露于热环境后尺寸稳定性和卷缩的测定

Resilient floor coverings - Determination of dimensional stability and curling after exposure to heat

18/30370190 DC BS ISO 10361 纺织地板覆盖物 通过 Vettermann 转鼓和六足转鼓测试仪进行外观变化

BS ISO 10361. Textile floor coverings. Production of changes in appearance by means of Vettermann drum and hexapod tumbler tester

ASTM F2982-18 聚酯组合物地板砖的标准规范

1.1 This specification covers polyester composition floor tile for use in commercial, light commercial or residential flooring applications. The tile may be either smooth or embossed. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Polyester Composition Floor Tile

ASTM F1304-18 弹性地板砖挠曲的标准试验方法

1.1 This test method is used to determine the deflection of relatively rigid resilient floor tile such as vinyl composition tile and resilient flooring with a rigid polymeric core. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Deflection of Resilient Floor Tile

DIN EN ISO 10582:2018 弹性地板覆盖物.多相聚乙烯(氯乙烯)地板覆盖物.规范(ISO 10582-2017);德文版本EN ISO 10582-2018

This International Standard specifies the characteristics of non-cushioned, heterogeneous floor coverings, based on polyvinyl chloride, supplied in either tile or roll form. Products may contain a transparent, non-PVC factory finish.To encourage the consumer to make an informed choice, the standard includes a classification system (see ISO 10874) based on intensity of use, which shows where these floor coverings should give satisfactory service. It also specifies requirements for marking.

Resilient floor coverings - Heterogeneous poly(vinyl chloride) floor covering - Specifications (ISO 10582:2017); German version EN ISO 10582:2018

BS ISO 19322:2018 弹性地板覆盖物 基于热塑性聚合物的地板覆盖物规范

1   Scope This document specifies the characteristics for resilient floor coverings based upon thermoplastic polymers , supplied either in roll, plank or tile form. To encourage the consumer to make an informed choice, this document includes a classification system (see ISO 10874) based on intensity of use, which shows where these floor coverings should give satisfactory service. It also specifies requirements for marking. This specification does not apply to floor coverings specified in ISO 10581, ISO 10582, ISO 10595, ISO 11638, ISO 10575, ISO 10577, ISO 24011 and ISO 26986.

Resilient floor coverings. Specification for floor coverings based on thermoplastic polymers

ASTM D7339-18 使用特定吸附剂管和热解吸/气相色谱法测定从地毯排出的挥发性有机化合物的标准试验方法

1.1 This test method describes an analytical procedure for identifying and quantifying the masses of individual volatile organic compounds (individual VOCs or IVOCs) that are emitted into a flow of air from carpet specimens and collected on sorbent sampling tubes during emissions testing. 1.2 This test method will be used in conjunction with a standard practice for sampling and preparing carpet specimens for emissions testing. If a specific chamber practice is not available for the carpet specimens, this test method should be used in conjunction with approved standard practices for emissions testing and sample preparation. 1.3 When used in conjunction with standard practices for carpet specimen preparation and collection of vapor-phase emissions , this test method will provide a standardized means of determining the levels of IVOC in the exhaust stream of the emissions test chamber/cell. If this test method is used with a reliable practice for emissions testing, these IVOC levels can be used to determine the emission rate from a unit quantity (usually surface area) of the sample material under test. 1.4 VOCs in the exhaust stream of an emissions test device are collected on thermal desorption tubes packed with a specific combination of sorbents using active (pumped) sampling. (See Practice D6196 for a more general description of vapor collection using pumped sampling onto sorbent tubes.) The samples are analyzed by thermal desorption (TD) with gas chromatography and mass spectrometry detection (GC/MS) and/or flame ionization detection (FID) depending upon the requirements of the specific materials emissions testing/ certification protocol. 1.5 This test method can be used for the measurement of most GC-compatible organic vapors ranging from the approximate volatility from n-hexane to n-hexadecane (that is, compounds with vapor pressures ranging from 16 kPa to 4 × 10-4 kPa at 25°C). Properties other than a compound’s vapor pressure such as affinity for the sorbent may need to be taken into account. Compounds with vapor pressures outside this range may or may not be quantifiable by this test method. However, qualitative data concerning the identity of a compound(s), outside the stated volatility range for quantitation, may still be useful to the user. This test method can be applied to analytes over a wide concentration range— typically 1 µg/m3 to 1 mg/m3 concentration of vapor in the exhaust air from the emission cell or chamber. 1.6 This test method is not capable of quantifying all compounds which are emitted from carpets. See the appropriate test practices/methods for determining other compounds that are not amenable to analysis by gas chromatography (that is, Test Method D5197 for the determination of aldehydes). 1.7 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Volatile Organic Compounds Emitted from Carpet using a Specific Sorbent Tube and Thermal Desorption / Gas Chromatography

ASTM F693-01(2018)e1 使用液体密封剂密封密封片材地板产品接缝的标准实施规程

1.1 This practice covers the instructions and precautions to be observed to ensure satisfactory performance of seams in sheet resilient flooring sealed with liquid seam sealers. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Sealing Seams of Resilient Sheet Flooring Products by Use of Liquid Seam Sealers

BS EN ISO 11378-2:2001+A1:2017 纺织地板覆盖物 实验室污染测试 转鼓测试

1   Scope 1.1    This part of ISO 11378 describes the equipment and the test method for assessing the propensity of textile floor coverings to soiling in the absence of abrasive wear and texture changes using a standard artificial soil composition.

Textile floor coverings. Laboratory soiling tests - Drum test

ISO 19322:2018 弹性地板覆盖物. 基于热塑性聚合物的地板覆盖物规范

This document specifies the characteristics for resilient floor coverings based upon thermoplastic polymers, supplied either in roll, plank or tile form. To encourage the consumer to make an informed choice, this document includes a classification system (see ISO 10874) based on intensity of use, which shows where these floor coverings should give satisfactory service. It also specifies requirements for marking. This specification does not apply to floor coverings specified in ISO 10581, ISO 10582, ISO 10595,

Resilient floor coverings - Specification for floor coverings based on thermoplastic polymers

BS EN ISO 10582:2018 弹性地板覆盖物 异质聚氯乙烯地板覆盖物 规格

1   Scope This document specifies the characteristics of non-cushioned, heterogeneous floor coverings , consisting of poly(vinyl chloride) (PVC), supplied in either tile or plank or roll form. Products can contain a transparent, non-PVC factory finish . To encourage the consumer to make an informed choice, this document includes a classification system (see ISO 10874) based on the intensity of use, which shows where these floor coverings give satisfactory service. It also specifies requirements for marking.

Resilient floor coverings. Heterogeneous poly(vinyl chloride) floor covering. Specifications

ASTM C1486-18 测试耐化学品广播和泥浆广播树脂整体地板表面的标准实践

1.1 This practice covers methods for preparing test specimens and testing procedures for broadcast or slurry-broadcast monolithic floor surfacings in areas where chemical resistance is required. 1.2 These floor surfacings are applied by various application methods including squeegees, rollers, trowels, notched trowels, and gage rakes onto suitably prepared concrete substrates. The surfacings bond to the substrate upon curing to provide a nominal thickness of 60 mils (1.5 mm) or greater. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Testing Chemical-Resistant Broadcast and Slurry-Broadcast Resin Monolithic Floor Surfacings

NF G35-005:2018 纺织地毯.重量测定方法

La présente Norme internationale prescrit des méthodes de détermination de la masse totale par unité de surface, de la masse totale de velours par unité de surface, de la masse de velours par unité de surface au-dessus du soubassement, et des méthodes de calcul de la masse volumique du velours de surface et de la densité de fibres dans le velours, des revêtements de sol textiles.

Textile floor coverings - Methods for determination of mass

T/CADBM 1-2018 聚氯乙烯锁扣地板

本标准规定了聚氯乙烯锁扣地板（以下简称锁扣地板）的术语和定义、产品分类、要求、试验方法、检验规则、标志、运输和贮存。

PVC locking floor

T/CADBM 2-2018 聚氯乙烯卷材运动地板

本标准规定了聚氯乙烯卷材运动地板(以下简称运动地板)的分类、要求、试验方法、检验规则、标志、包装、运输和贮存。

PVC Roll Sports Flooring