97.200.99 其他文娱活动设备 标准查询与下载

ASTM F2974-20 游乐设施和装置的审计标准实施规程

Standard Practice for Auditing Amusement Rides and Devices

T/GDMA 20-2019 中性笔

本标准规定了中性笔的分类、要求、试验方法、检验规则及包装、运输、贮存。本标准适用于一般书写的中性笔和笔芯。

gel pen

T/CSSGA 1025-2019 扑克牌

本标准规定了扑克牌的术语和定义、分类与组成、技术要求、试验方法、检验规则和标识、包装、运输、贮存

Playing cards

ASTM F2137-19 游乐设施和装置动态特性测量的标准实施规程

1.1 This practice covers acquisition of data related to the dynamic characteristics of amusement rides and devices. 1.2 This practice also defines the specific requirements of a Standardized Amusement Ride Characterization Test (SARC Test) for use in characterizing the dynamic motion of an amusement ride or device. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3.1 Exception—The values are reversed in Section 13 since EN standards primarily use SI units. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Measuring the Dynamic Characteristics of Amusement Rides and Devices

ASTM F770-19 游乐设施和装置的所有权、操作、维护和检验的标准实施规程

Standard Practice for Ownership, Operation, Maintenance, and Inspection of Amusement Rides and Devices

T/CSSGA 1022-2019 钓鱼竿

本标准规定了钓鱼竿的术语和定义、分类与标记、要求、试验方法、检验规则、标签、包装、运输及贮存。

Fishing rod

T/JMYYXH 1-2019 低空无人机拍摄安全规范

      本标准规定了无人机航摄安全作业的技术准备、实地踏勘与场地选取、飞行检查与操控、保障措施、设备使用与维护等内容。       本标准适用于最大起飞重量不超过50 kg，任务高度不超过1000米，无人机的飞行导航与控制系统采用微小型传感器为代表的高集成度元器件构成，空中与地面之间的数据传输采用轻小型数传电台，机上设备采用锂、镍氢、镍镉等电池组供电的低空旋翼轻型无人机航摄作业。

Safety regulations for low-altitude drone shooting

ASTM F1193-18a 游乐设施和装置的质量、制造和结构的标准实施规程

Standard Practice for Quality, Manufacture, and Construction of Amusement Rides and Devices

T/ZPPIA 004-2018 宠物口套

配件插接件正常开关500次，无异常。 金属镀层的耐腐蚀性能应不低于6级（喷雾周期为8h）。 口套的可触及金属边缘，包括孔、槽，不应含有危险的毛刺或斜薄边。 口套的面料和辅料中甲醛含量不应超过300 mg/kg。

Pet Muzzles

ASTM F2137-18 游乐设施和装置动态特性测量的标准实施规程

Standard Practice for Measuring the Dynamic Characteristics of Amusement Rides and Devices

ASTM F2974-18 游乐设施和装置的审计标准实施规程

Standard Practice for Auditing Amusement Rides and Devices

ASTM F770-18 游乐设施和装置的所有权、操作、维护和检验的标准实施规程

Standard Practice for Ownership, Operation, Maintenance, and Inspection of Amusement Rides and Devices

ASTM F1193-18 游乐设施和装置的质量、制造和结构的标准实施规程

Standard Practice for Quality, Manufacture, and Construction of Amusement Rides and Devices

T/ZPPIA 001-2018 宠物狗牵引绳（带）

抗拉力    （单位为N） 微型宠物狗　≥220 小型宠物狗　≥450 中型宠物狗　≥900 大型宠物狗　≥1300

Pet dog leash

T/CAAPA 0002-2018 礼品抓取贩卖机良好信息标识

根据最新颁布的《中华人民共和国标准化法》，标准包括国家标准、行业标准、地方标准和团体标准、企业标准。国家首次明确鼓励学会、协会、商会、联合会、产业技术联盟等社会团体协调相关市场主体共同制定满足市场和创新需要的团体标准，由本团体成员约定采用或者按照本团体的规定供社会自愿采用。 为了满足我国礼品抓取贩卖机对于标准的需求，规范其长期无序生产及运营的行业，提高顾客对礼品抓取贩卖机的美誉度，同时填补相关领域的标准空白，由中国游艺机游乐园协会提出并起草了本标准。 制定本团体标准，遵循开放、透明、公平的原则，保证了生产及运营的主体获取相关信息，也反映了各参与主体的共同需求，并对标准相关事项进行了调查分析、实验、论证。 本团体标准针对当下行业反映的问题，确立了礼品抓取贩卖机良好信息规范，对符合一系列规范的主体准许授予良好信息标识，也明确了包括申请、标识的变更、暂停和撤销在内的标识管理要求。 本团体标准为推荐性标准，鼓励行业内广泛采用。

Identification of good operation for doll machine

ASTM F3054-18 娱乐铁路车辆 设备和设施的操作标准实施规程

1.1 This practice applies to operations of amusement railway ride(s) that have a track gauge greater than or equal to 12 in. (305 mm) measured between the heads of the rails. This excludes patron powered ride vehicles specifically designed for children. 1.2 This standard does not apply to the operation of rides, such as roller coasters, that may resemble railways, but may fall within the scope of Practice F2291 or Practice F1159 and does not apply to funiculars as defined in ANSI B77.2 or BS EN 1907. 1.3 This standard does not apply to Amusement Railway Rides operation that are intended for use as a portable amusement ride or attraction. 1.4 This standard does not apply to permanently installed amusement railway rides and tourist railways, and their associated track, devices and facilities that are under the jurisdiction of the Federal Railroad Administration (FRA) in whole or part or National equivalent. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Operations of Amusement Railway Rides, Devices, and Facilities

ASTM F1193-17 游乐设施和装置的质量、制造和结构的标准实施规程

Standard Practice for Quality, Manufacture, and Construction of Amusement Rides and Devices

ASTM F770-17e1 游乐设施和装置的所有权、操作、维护和检验的标准实施规程

Standard Practice for Ownership, Operation, Maintenance, and Inspection of Amusement Rides and Devices

ASTM F2974-17a 游乐设备审查标准指南

1.1 This guide establishes guidelines for auditing conformance to ASTM Committee F24 Standards during an audit of an amusement ride or device within a defined scope. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Auditing Amusement Rides and Devices

ASTM F770-17 游乐设施和装置的所有权、操作、维护和检验的标准实施规程

1.1 This practice provides guidelines for operations, maintenance, and inspection procedures for amusement rides and devices to be performed by the owner/operator. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Ownership, Operation, Maintenance, and Inspection of Amusement Rides and Devices