97.220.30 标准查询与下载

ASTM F2810-10 椭圆形训练器材用标准规范

1.1 This specification establishes parameters for the design and manufacture of elliptical training equipment as defined in 3.1 for use in an indoor environment or setting. 1.2 It is the intent of this standard to specify fitness products for use only by an individual age 13 or older. 1.3 This standard is to be used in conjunction with Specification F2276 and Test Methods F2811. All specifications in this standard supersede those of Specification F2276 where applicable. 1.4 The values stated in SI units are to be regarded as standard. The values in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Elliptical Trainers

EN 957-6:2010 固定式健身器材第6部分:跑步机附加的特殊安全要求和试验方法

EN 957-6 specifies safety requirements and test methods for treadmills in addition to the general safety requirements and test methods of EN 957-1 and shall be read in conjunction with it. EN 957-6 is applicable to power-driven as well as to non-power/manually driven training equipment type treadmills (hereafter referred to as treadmills) with the classes S, H and I and classes A, B and C regarding accuracy.

Stationary training equipment - Part 6: Treadmills, additional specific safety requirements and test methods (Incorporates Amendment A1: 2014)

ANSI/ASTM F2811:2010 椭圆练习器性能特性和设计的评定方法

Test Methods for Evaluation Design and Performance Characteristics of Elliptical Trainers

ASTM F2276-10(2015) 健身器材的标准规格

1.1 This specification establishes parameters for the design and manufacture of fitness equipment as defined in 3.1.9. 1.2 It is intended that these fitness products be used in an indoor setting or environment. 1.3 It is the intent of this specification to specify products for use by individuals age 13 and above. 1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Fitness Equipment

ANSI/ASTM F2276:2010 健身器材规范

Specification for Fitness Equipment

ANSI/ASTM F2810:2010 椭圆形练习器规范

Specification for Elliptical Trainers

ASTM F2811-10 椭圆形训练器材的评估设计和性能特征用标准试验方法

The purpose of these test methods is to provide reliable and repeatable test methods for the evaluation of elliptical trainers assembled and maintained according to the manufacturer’s specifications. Use of these test methods, in conjunction with Specification , is intended to ensure appropriate performance and reliability of an elliptical trainer and reduce the risk of serious injury from design deficiencies.1.1 These test methods specify procedures and equipment used for testing and evaluating elliptical trainers for compliance to Specification . Both design and operational parameters will be evaluated. Where possible and applicable, accepted test methods from other recognized bodies will be used and referenced. In case of a conflict between this document and Specification , Specification takes precedence. 1.2 Requirements8212;An elliptical trainer is to be tested for all of the following parameters: 1.2.1 Endurance, 1.2.2 Static loading, 1.2.2.1 Handlebars 1.2.2.2 Foot supports 1.2.3 Adjustable guide systems, 1.2.4 Control panel, 1.2.5 Warnings, and 1.2.6 Documentation. 1.3 The values stated in SI units are to be regarded as the standard. The values in parenthesis are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Evaluating Design and Performance Characteristics of Elliptical Trainers

KS G ISO 20957-10:2009 固定的训练器材.第10部分:带固定轮或无自由飞轮的训练自行车、附加特定安全要求和试验方法

이 표준은 KS G ISO 20957-1의 일반 안전 요구사항에 추가하여 0.6 kgㆍm2

Stationary training equipment-Part 10 :Exercise bicycles with a fixed wheel or without freewheel, additional specific safety requirements and test methods

KS G ISO 20957-9:2009 固定式训练设备.第9部分:椭圆形训练器材的附加特殊安全要求和试验方法

이 표준은 KS G ISO 20957-1의 일반 안전 요구사항에 추가하여 교차 훈련 기구로

Stationary training equipment－Part 9：Elliptical trainers,additional specific safety requirements and test methods

ASTM F1081-09 竞赛摔跤标准规范

The mats shall be constructed to yield the values listed in Table 1 throughout the mat area under the conditions of the manufacturer's warranty. Special requirements for the mats shall be subject to purchase agreements. Special requirements shall never reduce any of the basic requirements listed in this standard. Good manufacturing practices shall be used in the construction and inspection of the mats.1.1 This specification covers competition wrestling mats used at the high school and college levels. All mat constructions are included, except felt-core mats enclosed in sewn covers. The intended use of this standard is for the qualification of construction designs. Note 18212;The known constructions, as of the issuance of this specification are: (1) closed-cell foam cores with polyvinyl chloride (PVC) or PVC copolymer coatings, or both, which are integral parts of the mat; (2) closed-cell foam cores with attached fabric cover; (3) foam cores, either open- or closed-cell enclosed in sewn, loose covers, and (4) molded open-cell PVC foam with a dense skin on one surface which is an integral part of the mat. Note 28212;There is no known ISO equivalent to this standard. 1.2 This specification covers mats used in the two major styles of wrestling: U.S. collegiate or high school, and international free style. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See Note 6 for specific hazards statements.

Standard Specification for Competition Wrestling Mats

GSO ASTM F2106:2009 评估电动跑步机的设计和性能特征的标准测试方法

1.1 These test methods specify procedures and equipment used for testing and evaluating a motorized treadmill for compliance to Specification F 2115. Both design and operational parameters will be evaluated. Where possible and applicable, accepted test methods from other recognized bodies will be used and referenced. In case of a conflict between this document and Specification F 2115, Specification F 2115 takes precedence. 1.2 Requirements—Amotorized treadmill is to be tested for all of the following parameters: 1.2.1 Stability, 1.2.2 Exterior design, 1.2.3 Endurance, 1.2.4 Static loading, 1.2.5 Overheating, 1.2.6 Adjustable incline system function, 1.2.7 User interface parameters, 1.2.8 Motorized drive system operation, 1.2.9 Warning label compliance, and 1.2.10 Documentation.

Standard Test Methods for Evaluating Design and Performance Characteristics of Motorized Treadmills

GSO ASTM F2115:2009 电动跑步机标准规范

1.1 This specification covers the establishment of parameters for the design and manufacture of motorized treadmills. 1.2 It is intent of this specification to specify products for use by individuals age 12 and above. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Motorized Treadmills

GSO ASTM F2276:2009 健身器材标准规范

1.1 This specification establishes parameters for the design and manufacture of fitness equipment as defined in 3.1.8. 1.2 It is the intent of this specification to specify products for use by individuals age 12 and above. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Fitness Equipment

BS EN 957-5:2009 固定的训练器材.固定自行车和曲柄上身训练器材,附加特殊的安全要求和测试方法

Stationary training equipment - Stationary exercise bicycles and upper body crank training equipment, additional specific safety requirements and test methods

LST EN 957-5-2009 固定式训练设备 第5部分：固定式健身自行车和上半身曲柄训练设备，附加特定安全要求和测试方法

Stationary training equipment - Part 5: Stationary exercise bicycles and upper body crank training equipment, additional specific safety requirements and test methods

BS EN 914:2008 体操设备.双杠和组合高低杠/双杠.含安全性的试验方法和要求

This European Standard specifies functional requirements (see Clause 3) and specific safety requirements in addition to the general safety requirements in EN 913 (see Clause 4), which shall be read in conjunction with this standard. This European Standard is applicable to 2 types of parallel bars (see Table 1) intended for use under supervision of a competent person.

Gymnastic equipment - Parallel bars and combination asymmetric/parallel bars - Requirements and test methods including safety

BS EN 913:2008 体操器材.试验方法和一般安全性要求

This European Standard specifies general safety requirements and test methods for all pieces of gymnastic equipment intended for use supervised by a competent person and not specified in other, individual standards. This European Standard is not applicable to other sport equipment, playground equipment, stationary training equipment or educational training equipment.

Gymnastic equipment - General safety requirements and test methods

BS EN 915:2008 体操器材.高低杠.包括安全性的试验方法和要求

This European Standard specifies functional requirements (see Clause 3) and specific safety requirements in addition to the general safety requirements in EN 913 (see Clause 4) which shall be read in conjunction with this standard. This European Standard is applicable to 2 types of asymmetric bars (see Table 1) intended for use under supervision of a competent person.

Gymnastic equipment - Asymmetric bars - Requirements and test methods including safety

BS EN 13219:2008 体操设备.蹦床.功能,试验方法和安全性要求

This European Standard specifies functional requirements for five types of trampolines (see Clause 3) and specific safety requirements (see Clause 4) in addition to the general safety requirements of EN 913. This European Standard is applicable to five types of trampolines intended for use under qualified supervision of a competent person as identified in Table 1. It does not apply to tumble tracks (fast tracks), trampolines and mini-trampolines intended for home use, safety harnesses or other accessories.

Gymnastic equipment - Trampolines - Functional and safety requirements, test methods

DIN EN 957-5:2009 固定式训练设备.第5部分:固定式健身脚踏车和上身曲柄训练装置,附加特殊安全性要求和试验方法.英文版本DIN EN 957-5-2009-07

This part of EN 957 specifies safety requirements for stationary exercise bicycles and upper body crank training equipment in addition to the general safety requirements of EN 957-1. This part of EN 957 is applicable to stationary training equipment type stationary exercise bicycles and upper body crank training equipment (type 5) as defined in Clause 3 within the classes S, H, I and A, B, C according to EN 957-1. Any attachment provided with the stationary exercise bicycles and upper body crank training equipment for the performance of additional exercises are subject to the requirements of EN 957-1. This part of EN 957 is not applicable to roller stands as they cannot be made safe in a reasonable way.

Stationary training equipment - Part 5: Stationary exercise bicycles and upper body crank training equipment, additional specific safety requirements and test methods; English version of DIN EN 957-5:2009-07