A50 计量综合 标准查询与下载

ISO 22432:2011 产品几何形状规范(GPS).规格说明和验证特点

Geometrical product specifications (GPS) - Features utilized in specification and verification

DIN EN ISO 1101 Berichtigung 1:2011 几何产品技术规范(GPS).形状,方向,位置和同心度的几何公差(ISO 1101-2004);德文版本EN ISO 1101-2005,DIN EN ISO 1101-2008-08的技术勘误表

Geometrical Product Specifications (GPS) - Geometrical tolerancing - Tolerances of form, orientation, location and run-out (ISO 1101:2004); German version EN ISO 1101:2005, Corrigendum to DIN EN ISO 1101:2008-08

DIN EN ISO 14253-3:2011 几何产品技术规范(GPS).对工件和测量设备进行测量的检查.第3部分:就测量不确定报表达成一致意见的指南(ISO 14253-3-2011);德文版本EN ISO 14253-3-2011

Geometrical product specifications (GPS) - Inspection by measurement of workpieces and measuring equipment - Part 3: Guidelines for achieving agreements on measurement uncertainty statements (ISO 14253-3:2011); German version EN ISO 14253-3:2011

BS EN ISO 772:2011 液体比重测定法.词汇和符号

This International Standard gives terms, definitions and symbols used in standards in the field of hydrometry.

Hydrometry. Vocabulary and symbols

JIS Z 8462-5:2011 检测能力.第5部分:线性和非线性校准容器中的方法体系

Capability of detection -- Part 5: Methodology in the linear and non-linear calibration cases

DB12/T 443-2011 采暖期室内温度测量方法

本标准规定了采暖期室内温度测量的术语和定义、测量条件要求、采暖期室内温度要求及测量方法。本标准适用于采暖期室内温度的测量。非采暖期室内温度的测量科参照本标准测量方法。

Indoor Temperature Measurement Method in Heating Period

ISO 5459:2011 产品几何技术规范(GPS).几何公差.基准和基准体系

This International Standard specifies terminology, rules and methodology forthe indication and understanding of datums and datum systems in technical product documentation. This International Standard also provides explanations to assist the User in understanding the concepts involved. This International Standard defines the specification operator (see ISO 17450-2) used to establish a datum or datum System，The verification operator (see 1SO 17450-2) can take different forms (physically or mathematically) and is not the subject of this International Standard. NOTE The detailed rules for maximum and least material requirements for datums are given in 1SO 2692.

Geometrical product specifications (GPS) - Geometrical tolerancing - Datums and datum systems

BS EN ISO 12180-1:2011 产品几何技术规范(GPS).圆柱度.圆柱形词汇和参数

This part of ISO 12180 defines the terms and concepts related to cylindricity of individual complete integral features only.

Geometrical product specifications (GPS). Cylindricity. Vocabulary and parameters of cylindrical form

BS EN ISO 12180-2:2011 产品几何技术规范(GPS).圆柱度.规范操作集

This part of ISO 12180 specifies the complete specification operator for cylindricity of complete integral features only, i.e. geometrical characteristics of features of type cylinder.

Geometrical product specifications (GPS). Cylindricity. Specification operators

BS EN ISO 12781-1:2011 产品几何技术规范(GPS).平整度.平整度词汇和参数

This part of ISO 12781 defines the terms and concepts related to flatness of individual complete integral features only.

Geometrical product specifications (GPS). Flatness. Vocabulary and parameters of flatness

BS EN ISO 12781-2:2011 产品几何量技术规范(GPS).平整度.规范操作集

This part of ISO 12781 specifies the complete specification operator for flatness of complete integral features only, i.e. geometrical characteristics of individual features of type plane.

Geometrical product specifications (GPS). Flatness. Specification operators

DB34/T 1383-2011 成品油经营企业（加油站）诚信计量要求

本标准规定了成品油经营企业诚信计量的要求、评价与声明等。本标准适用于已经通过测量管理体系认证并有效运行，有诚信愿望的相关企业。

Integrity Measurement Requirements for Refined Oil Operating Enterprises (Gas Stations)

DB34/T 1384-2011 供电企业诚信计量要求

本标准规定了供电企业诚信计量的要求、评价与声明等。本标准适用于已经通过测量管理体系认证并有效运行，有诚信愿望的相关企业。

Integrity measurement requirements of power supply enterprises

JJG(铁道) 120-2011 客车轮对轴颈中心距尺

本规程适用于分度值为0.05mm或0.10mm的客车轮对轴颈中心距尺的首次检定、后续检定和使用中检验。

Gauge Used in Measuring the Distance Between Acting Centres of Journal Load of Wheels - set for Coach

ISO 12181-2:2011 产品几何量技术规范(GPS).圆形.第2部分:规范操作人员

This part of ISO 12181 specifies the complete specification operator for roundness of integral features only and covers complete roundness profiles only, i.e. geometrical characteristics of features of the type circle.

Geometrical product specifications (GPS) - Roundness - Part 2: Specification operators

ISO 12781-2:2011 产品几何技术规范(GPS).平整度.第2部分:操作规程

This part of ISO 12781 specifies the complete specification operator for flatness of complete integral features only, i.e. geometrical characteristics of individual features of type plane.

Geometrical product specifications (GPS) - Flatness - Part 2: Specification operators

ISO 25378:2011 产品几何量技术规范(GPS).特征与条件.定义

This International Standard defines general terms for geometrical specifications, characteristics and conditions. These definitions are based on concepts developed in ISO 17450-1 and ISO 22432 and they are given by using a mathematical description based on Annex B of ISO 17450-1:2011. This International Standard is not intended for industrial use as such among designers, but is aimed to serve as the “road map” mapping out the requirements based on geometrical features, thus enabling future standardization for industry and software makers in a consistent manner. This International Standard defines general types of geometrical characteristics and conditions which can be used in GPS. These descriptions are applicable to - a workpiece, - an assembly, - a population of workpieces, and - a population of assemblies. These definitions are based on concepts of operators and the duality principle contained in ISO 17450-1 and ISO/TS 17450-2 and on the description of types of geometrical features defined in ISO 22432. Conceptually, these specification operators can be used as specification operators or as verification operators (duality principle). This International Standard is not intended to define GPS specifications, symbology or other types of expression.

Geometrical product specifications (GPS) - Characteristics and conditions - Definitions

ISO 12180-1:2011 产品几何量技术规范(GPS).圆柱度.第1部分:圆柱构造的词汇与参数

This part of ISO 12180 defines the terms and concepts related to cylindricity of individual complete integral features only.

Geometrical product specifications (GPS) - Cylindricity - Part 1: Vocabulary and parameters of cylindrical form

ISO 12180-2:2011 产品几何量技术规范(GPS).圆柱度.第2部分:规范操作人员

This part of ISO 12180 specifies the complete specification operator for cylindricity of complete integral features only, i.e. geometrical characteristics of features of type cylinder.

Geometrical product specifications (GPS) - Cylindricity - Part 2: Specification operators

ISO 12780-1:2011 产品几何技术规范(GPS).平直度.第1部分:平直度的词汇和参数

This part of ISO 12780 defines the terms and concepts related to straightness of individual integral features and covers complete straightness profiles only. NOTE Straightness of an extracted derived axis of a cylinder is defined in ISO 12180-1 and ISO 12180-2.

Geometrical product specifications (GPS) - Straightness - Part 1: Vocabulary and parameters of straightness