A82 包装材料与容器 标准查询与下载
共找到 3262 条与 包装材料与容器 相关的标准，共 218 页
Packaging material Coated antistatic polyethylene terephthalate (PET) sheet (coil)
- ICS
- ICS55.040
- CCS
- A82
- 发布
- 2019-05-02
- 实施
- 2019-11-01
This European Standard specifies the requirements for above-ground containers, mechanically lifted and emptied, used for the selective collection of solid non-hazardous waste, with capacities from 80 l to 5 000 l. The standard specifies the general characteristics of such containers and their accessories, the test methods and the safety requirements.
Stationary waste containers up to 5 000 l, top lifted and bottom emptied. Additional requirements for underground or partly underground systems
- ICS
- 13.030.40
- CCS
- A82
- 发布
- 2019-01-01
- 实施
- 2019-01-01
Packaging. Cork mouth finish with a bore diameter of 18,5 mm for corks and tamper evident capsules
- ICS
- 55.100
- CCS
- A82
- 发布
- 2018-10-15
- 实施
- 2018-10-15
This document covers the emergency pressure relief valve of tanks for transport of dangerous goods. It specifies the performance requirements and the critical dimensions of the emergency pressure relief valve. It also specifies the tests necessary to verify the compliance of the equipment with this document. The service equipment specified by this document is suitable for use with liquid petroleum products and other dangerous substances of Class 3 of ADR which have a vapour pressure not exceeding 110 kPa at 50 °C and petrol, and which have no sub-classification as toxic or corrosive.
Tanks for transport of dangerous goods - Service equipment for tanks - Emergency pressure relief valve; German version EN 14596:2018
- ICS
- 13.300;23.020.20;23.060.40
- CCS
- A82
- 发布
- 2018-10-00
- 实施
Tanks for transport of dangerous goods. Service equipment for tanks. Emergency pressure relief valve
- ICS
- 13.300;23.020.20;23.060.40
- CCS
- A82
- 发布
- 2018-09-05
- 实施
- 2018-09-05
This standard specifies mating dimensions of sockets for use on containers (casks and kegs) for beer and non-alcoholic beverages, and for connectors to be screwed into these sockets. The mating dimensions specified in this standard permit sockets to be used with all commercially available containers as in DIN 6647-1und DIN 6647-2 and the associated connectors to be screwed into these sockets to be fitted with commercial valve systems.
Connectors and sockets for beverage containers - Mating dimensions
- ICS
- 23.040.60;67.260
- CCS
- A82
- 发布
- 2018-09-01
- 实施
Workshop fabricated steel tanks. Horizontal cylindrical single skin and double skin tanks for the underground storage of flammable and nonflammable water polluting liquids other than for heating and cooling of buildings
- ICS
- 13.300;23.020.10
- CCS
- A82
- 发布
- 2018-07-05
- 实施
- 2018-07-05
1、规定了采用应变强化技术制造移动式真空绝热深冷压力容器内容器用钢材料的牌号、力学性能要求和复验要求，并给出了内容器非金属支撑材料的技术要求。 2、明确了应变强化内容器的设计载荷、许用应力、设计压力、开孔补强计算、强化压力的要求，并给出了应变强化内容器结构设计的关键技术要求，重点介绍了夹层支撑结构设计的典型型式和技术要求。 3、规定了应变强化容器制造过程中，材料制备、加工成形、焊接和无损检测方面的特殊要求，重点就焊接工艺评定的具特殊要求进行了规定。 4、以资料性附录的形式，给出了应变强化内容器制造过程中重要质量控制点、应变强化工艺验证性试验要求、试件预拉伸及试验规则等要求；用规范性附录形式，规定了应变强化处理的相关要求。
Transportable vacuum insulated cryogenic pressure vessels—Requirement of pressure strengthening for inner vessels
- ICS
- 23.020.40
- CCS
- A82
- 发布
- 2018-07-05
- 实施
- 2018-07-05
Two-way heat-shrinkable polyester film for packaging
- ICS
- ICS55.040
- CCS
- A82
- 发布
- 2018-07-04
- 实施
- 2019-01-01
Cryogenic vessels - Pressure-relief accessories for cryogenic service - Part 2: Non-reclosable pressure-relief devices; Amendment 1
- ICS
- 23.020.40
- CCS
- A82
- 发布
- 2018-07-00
- 实施
Tanks for the transport of dangerous goods - Transport tank equipment for overfill prevention devices for static tanks
- ICS
- 13.300;23.020.10;75.200
- CCS
- A82
- 发布
- 2018-06-27
- 实施
La présente Norme européenne spécifie les prescriptions minimales de performance et de construction applicables aux contrôleurs limiteurs de remplissage installés sur le véhicule-citerne.
Tanks for the transport of dangerous goods - Transport tank equipment for overfill prevention devices for static tanks
- ICS
- 13.300;23.020.10;75.200
- CCS
- A82
- 发布
- 2018-06-27
- 实施
- 2018-08-25
Packaging container stand-up pouch
- ICS
- ICS55.120
- CCS
- A82
- 发布
- 2018-03-01
- 实施
- 2018-09-01
This document specifies the toughness requirements of metallic materials for use at temperatures between −20 °C and −80 °C to ensure their suitability for cryogenic vessels. This document is applicable to fine-grain and low-alloyed steels with specified yield strength ≤460 N/mm2, aluminium and aluminium alloys, copper and copper alloys and austenitic stainless steels. NOTE For steel materials listed in EN 13445-2 or EN 13480-2 or for steel materials and weldings complying with the same fundamental safety requirements, the requirements for prevention of brittle fracture at low temperatures according to EN 13445-2:2014, Annex B, method 2, or EN 13480-2:2012, Annex B, method 2 can be applied.
Cryogenic vessels - Toughness requirements for materials at cryogenic temperature - Part 2: Temperatures between -80 degrees C and -20 degrees C
- ICS
- 23.020.40
- CCS
- A82
- 发布
- 2018-03-01
- 实施
Cryogenic vessels - Transportable vacuum insulated vessels of not more than 1 000 litres volume - Part 1: Design, fabrication, inspection and tests
- ICS
- 23.020.40
- CCS
- A82
- 发布
- 2018-02-01
- 实施
Tanks for transport of dangerous goods. Digital interface for the data transfer between tank vehicle and with stationary facilities. Protocol specification. Control, measurement and event data
- ICS
- 13.300;23.020.10;35.240.60
- CCS
- A82
- 发布
- 2018-01-03
- 实施
- 2018-01-03
Packaging. Transport packaging for dangerous goods. Comparative material testing of polyethylene grades
- ICS
- 13.300;55.040
- CCS
- A82
- 发布
- 2017-11-28
- 实施
- 2017-11-28
One-piece aluminum aerosol can for packaging container refrigerant
- ICS
- ICS55.140
- CCS
- A82
- 发布
- 2017-11-07
- 实施
- 2018-04-01
Packaging Container One-Piece Aluminum Bottle
- ICS
- ICS55.140
- CCS
- A82
- 发布
- 2017-11-07
- 实施
- 2018-04-01
