B69 木材加工材 标准查询与下载

BS EN 15146:2006 实心软木厚镶板层板.不带舌和槽的机加工形状

This European Standard defines the characteristics of solid wood panelling and cladding without tongue and groove on edges, machined from the following most common European species of softwood: spruce/fir, pine, larch, European Douglas fir and maritime pine. Products are intended for interior or exterior use. Coatings and finishings are not dealt with in this European Standard. NOTE products sold in the European Economic Area will have to comply with EN 14915.

Solid softwood panelling and cladding - Machined profiles without tongue and groove

DIN EN 13307-1:2007 不作结构材料用木制坯件和半成品材.第1部分:要求

This European Standard specifies requirements for timber blanks and semi-finished profiles for non-structural uses, including glued laminated and glued finger jointed products. This Standard gives specific requirements for dimensions, stability and moisture content. This Standard applies to hardwood and to softwood for use in joinery. Production control requirements and tests are given in prCEN/TS 13307-2.

Timber blanks and semi-finished profiles for non-structural uses - Part 1: Requirements; English version of DIN EN 13307-1:2007-01

ASTM D5055-07 确定和监测预制木质工字托梁的结构负载量用标准规范

1.1 This specification gives procedures for establishing, monitoring, and reevaluating structural capacities of prefabricated wood I-joists. Capacities considered are shear, moment, and stiffness. Procedures for establishing common details are given and certain design considerations specific to wood I-joists are itemized.1.2 Contents of the StandardAn index and brief description of the main features of this specification are given in .1.3 Development of the Standard - The development and intent of this specification is discussed in Appendix X1.1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. A specific precautionary statement is given in 6.1.1.5.

Standard Specification for Establishing and Monitoring Structural Capacities of Prefabricated Wood I-Joists

ASTM D2395-07ae1 木材和木基材料比重的标准试验方法

The specific gravity of wood gives an excellent measure of the amount of wood substance present in a sample. Thus, it may serve as a valuable indicator of the amount of wood pulp that could be produced, the workability of the material, or the strength characteristics of a specimen or a species. It should be recognized that specific gravity varies between trees, within a tree, and between species. Since the specific gravity of wood substance is practically constant for all species (approximately 1.53), it is apparent that individual specific gravity values are indicative of the amount of wood substance present. It affords a rapid and valuable method for selection of wood for specific uses. It may be desirable to know the specific gravity of a living tree, a structural member already in place, a log cross section, a segment of a research element, or the earlywood or latewood layer. The specimen thus may be large or small, regular or irregular, and at a variety of moisture contents. These test methods give procedures that include all of these variables and provides for calculation of specific gravity values to degrees of accuracy generally needed.1.1 These test methods cover the determination of the specific gravity of wood and wood-based materials to generally desired degrees of accuracy and for specimens of different sizes, shapes, and moisture content conditions. The method title is indicative of the procedures used or the specific area of use. Section Test Method A—Volume by Measurement7 Test Method B—Volume by Water Immersion8 Test Method C—Flotation Tube9 Test Method D—Forstner Bit10 Test Method E—Increment Core11 Test Method F—Chips12 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Specific Gravity of Wood and Wood-Based Materials

ASTM D1165-07 商业硬木和软木的标准术语

The purpose of this standard is to provide common tree names and botanical names for commercial species and species groups but is not intended to be all inclusive of commercial practice. The decision about which commercial species are included in this practice is made by the D07 committee on wood. Individual species are frequently mixed in commercial species groups for marketing or harvesting convenience, or for similar appearance or performance properties, or both. Consumers of lumber, plywood, and other wood-based products may use different mixes of species for the same species group name. This practice should provide clarity for nomenclature used throughout wood-consuming industries.1.1 Commercial species group names are listed with common tree and botanical names. Commercial names are representative of commercial practice in the United States and Canada. Some foreign species that are used in the United States and Canada are listed in Appendix X1 with their commercial and botanical names.1.2 The official common names conform AH 41. In addition to the official common name for a species, the checklist also lists other names by which the species and the lumber produced from it are sometimes designated. Names unique to Canada are shown with an *.1.3 The designations in parentheses, (North) and (South), a convention used by the American Lumber Standard (ALS) Committee accredited lumber rules writing agencies listed in ALS PS 20, identify a commercial name applied only when the included species are harvested from Canada as (North) or the United States as (South).

Standard Nomenclature of Commercial Hardwoods and Softwoods

ASTM D4442-07 木材和木基材料的直接水分测量用标准试验方法

1.1 These test methods cover the determination of the moisture content (MC) of solid wood, veneer, and other wood-base materials, including those that contain adhesives and chemical additives. The test methods below describe primary (A) and secondary (B through D) procedures to measure moisture content: Method A-Primary Oven-Drying MethodMethod B-Secondary Oven-Drying MethodMethod C-Distillation (Secondary) MethodMethod D-Other Secondary Methods. 1.2 The primary oven-drying method (Method A) is intended as the sole primary method. It is structured for research purposes where the highest accuracy or degree of precision is needed. 1.3 The secondary methods (B through D) are intended for special purposes or under circumstances where the primary procedure is not desired or justified. In these procedures, moisture content values cannot be reported with an accuracy greater than integer percentage values. However, a greater level of accuracy may be reported if the appropriate primary procedures are used. 1.4 Distillation (secondary) method is intended for use with materials that have been chemically treated or impregnated such that the oven-drying procedures introduce greater error than desired in the results.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Direct Moisture Content Measurement of Wood and Wood-Base Materials

ASTM D1990-07 来自于全尺寸试样的分级试验的目视尺寸分级的木材的容许性能的确定用标准试验方法

1.1 Due to the number of specimens involved and the number of mechanical properties to be evaluated, a methodology for evaluating the data and assigning allowable properties to both tested and untested grade/size cells is necessary. Sampling and analysis of tested cells are covered in Practice D 2915. The mechanical test methods are covered in Test Methods D 198 and D 4761. This practice covers the necessary procedures for assigning allowable stress and modulus of elasticity values to dimension lumber from In-Grade tests. The practice includes methods to permit assignment of allowable stress and modulus of elasticity values to untested sizes and grades, as well as some untested properties.1.2 A basic assumption of the procedures used in this practice is that the samples selected and tested are representative of the entire global population being evaluated. This approach is consistent with the historical clear wood methodology of assigning an allowable property to visually-graded lumber which was representative of the entire growth range of a species or species group. Every effort shall be made to ensure the test sample is representative of population by grade and size (see 7.1.1 and 7.1.2).1.3 This practice covers the principles and procedures for establishing allowable stress values for bending, tension parallel to grain, compression parallel to grain and modulus of elasticity values for structural design from "In-Grade" tests of full-size visually graded solid sawn dimension lumber. This practice is focused on, but is not limited to, grades which used the concepts incorporated in Practice D 245 and were developed and interpreted under American Softwood Lumber PS 20-70.Note 1 - In the implementation of the North American In-Grade test program, allowable stress values for compression perpendicular to grain and shear parallel to grain for structural design were calculated using the procedures of Practice D 245.1.4 This practice only covers dimension lumber.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Establishing Allowable Properties for Visually-Graded Dimension Lumber from In-Grade Tests of Full-Size Specimens

ASTM D3201-07 防火木材和木制品吸湿特性的标准试验方法

The hygroscopic properties of wood and wood-based products treated with fire-retardant chemicals are often greater than for untreated products. This is particularly true at the higher relative humidity conditions. This higher hygroscopicity sometimes is the cause for staining, decay, poor paint adhesion, and migration and exuding of chemicals and moisture at the high humidities. Corrosion of metal fasteners sometimes also occurs. The results obtained with this standard are important in identifying treatments with low hygroscopic properties. Results can be useful in determining exposure limitations in service for specific treated products. Building codes and other specifications for fire-retardant-treated wood for interior use include requirements based on this test method.1.1 This test method prescribes the procedure for determining the moisture content of fire-retardant-treated wood and wood-based product samples after exposure to a standard high relative humidity condition of 92 177; 2 % at 27 177; 2176;C (81 177; 4176;F).1.2 The text of this test method references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this test method.1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Hygroscopic Properties of Fire-Retardant Wood and Wood-Based Products

ASTM D2395-07a 木材和木基材料比重的标准试验方法

The specific gravity of wood gives an excellent measure of the amount of wood substance present in a sample. Thus, it may serve as a valuable indicator of the amount of wood pulp that could be produced, the workability of the material, or the strength characteristics of a specimen or a species. It should be recognized that specific gravity varies between trees, within a tree, and between species. Since the specific gravity of wood substance is practically constant for all species (approximately 1.53), it is apparent that individual specific gravity values are indicative of the amount of wood substance present. It affords a rapid and valuable method for selection of wood for specific uses. It may be desirable to know the specific gravity of a living tree, a structural member already in place, a log cross section, a segment of a research element, or the earlywood or latewood layer. The specimen thus may be large or small, regular or irregular, and at a variety of moisture contents. These test methods give procedures that include all of these variables and provides for calculation of specific gravity values to degrees of accuracy generally needed.1.1 These test methods cover the determination of the specific gravity of wood and wood-based materials to generally desired degrees of accuracy and for specimens of different sizes, shapes, and moisture content conditions. The method title is indicative of the procedures used or the specific area of use.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Specific Gravity of Wood and Wood-Based Materials

ASTM D2395-07 木材和木基材料比重的标准试验方法

1.1 These test methods cover the determination of the specific gravity of wood and wood-based materials to generally desired degrees of accuracy and for specimens of different sizes, shapes, and moisture content conditions. The method title is indicative of the procedures used or the specific area of use.SectionMethod A8212;Volume by Measurement6Method B8212;Volume by Water Immersion9Method C8212;Flotation Tube12Method D8212;Forstner Bit15Method E8212;Increment Core18Method F8212;Chips211.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Specific Gravity of Wood and Wood-Based Materials

SANS 6033:2006 粘结接合中的木材损坏百分比

Specifies a method for testing the determination of the wood failure percentage in an adhesive joint.

Wood failure percentage in an adhesive joint

KS F 3024-2006 中密度纤维板门框材料

이 규격은 건축물에 사용되는 중밀도 섬유판 문틀재(이하 틀재라고 한다.)에 대하여 규정한다

Medium Density Fiberboard(MDF) door frames

KS F 3101-2006 普通合板

이 규격은 보통 합판에 대하여 규정한다.

Ordinary plywood

SANS 1460:2006 层压木材（胶合层积材）

Covers general requirements for softwood and hardwood laminated members that consist of laminations glued or otherwise bonded together with the general fibre direction parallel to the longitudinal or curved axis of each member.

Laminated timber (glulam)

BS EN 13307-1:2006 不作结构材料的木制坯件和半成品材.要求

This European Standard specifies requirements for timber blanks and semi-finished profiles for non-structural uses, including glued laminated and glued finger jointed products. This Standard gives specific requirements for dimensions, stability and moisture content. This Standard applies to hardwood and to softwood for use in joinery. Production control requirements and tests are given in prCEN/TS 13307-2.

Timber blanks and semi-finished profiles for non-structural uses - Part 1: Requirements

BS EN 14915:2006 实心木质镶板和贴面层.特征、合格评定和标记

This European Standard defines and specifies the relevant characteristics and the appropriate test methods to determine these characteristics for products (including sidings) used in solid wood panelling and cladding for: ? wall and ceiling panelling for internal use; ? wall and ceiling cladding for external uses. It provides for the evaluation of conformity and the requirements for marking these products. The products are not evaluated for stiffening functions. This European Standard covers treated as well as untreated wood and it covers finger jointed and edge glued products. This European Standard covers products in compliance with EN 14519, EN 14951 and prEN 15146 but it also covers other solid timber products suitable for panelling and cladding. This European Standard does not cover products which are produced from laminated layer section.

Solid wood panelling and cladding - Characteristics, evaluation of conformity and marking

BS EN 335-1:2006 木制品和木基质产品的耐久性.使用等级定义.总则

This part of EN 335 defines five use classes which represent different service situations to which wood and wood-based products can be exposed. This part of EN 335 also indicates the biological agents relevant to each situation. Annex A gives information on these biological agents.

Durabiltity of wood and wood-based products - Definitions of use classes - General

BS EN 335-2:2006 木制品和木基质产品的耐侵袭性.使用等级定义.实心木材应用

This part of EN 335 offers guidance on the application to solid wood of the use classes, as defined in Part 1 of EN 335, in relation to the biological agents that can attack solid wood and solid wood panels. NOTE Due to their specific behaviour against biological agents, solid wood panels are considered in this part of EN 335, as solid wood. This Part shall be used in conjunction with Part 1 of EN 335. Annex A gives information and guidance for the user to determine the appropriate use class and to select a suitable level of durability (either natural or conferred by preservative treatment). It does not give guidance on protective measures other than preservative treatment.

Durability of wood and wood-based products - Definition of use classes - Application to solid wood

KS F ISO 16983:2006 木质板材.浸水后厚度膨胀的测定

이 규격은 목질 판재(1)의 흡수 두께 팽창율 측정 방법에 대하여 규정하며, 이 시험 방법

Wood-based panels-Determination of swelling in thickness after immersion in water

KS F ISO 16985:2006 木质板材.随相对湿度改变板材尺寸变化的测量

이 규격은 주변 환경의 상대 습도 변화에 따른 목질 판재(1)의 치수 안정성 시험 방법에

Wood-based panels-Determination of dimensional changes associated with changes in relative humidity