共找到 776 条与 木材加工材 相关的标准,共 52 页
Corkwood in planks, virgin cork, ramassage, gleanings, corkwood refuse and corkwaste - Determination of moisture content.
The document specifies a test method for determining the withdrawal capacity of fasteners inserted into wood-based panels. This test method can be used for any combination of fastener type and wood-based panel product. Note: This method differs from EN 320 which characterises fibreboards in terms of their resistance to the withdrawal load of only a single type of screw.
Wood-based panels - Determination of withdrawal capacity of fasteners; German version EN 13446:2002
This European Standard specifies a method for the determination of strength, stiffness, creep and duration of load when wood-based panels are loaded in edgewise bending. It is not applicable to extruded panels.
Wood-based panels - Determination of edgewise bending properties; German version EN 13879:2002
This International Standard specifies a method to enumerate the colony-forming units of yeasts, moulds and bacteria which can exist on cork stoppers and can grow in an alcoholic solution under certain conditions. This International Standard applies to cork stoppers which were submitted to the usual sanitizing procedures.
Cork stoppers - Enumeration of colony-forming units of yeasts, moulds and bacteria capable of growth in an alcoholic medium
This European Standard defines a non-destructive method for estimating the moisture content of a piece of timber using an electrical resistance meter. This standard applies to sawn timber, and timber which has been planed or surfaced by other means.#,,#
Moisture content of a piece of sawn timber - Part 2: Estimation by electrical resistance method; German version EN 13183-2:2002
This European Standard defines the method for determining the moisture content of a piece of sawn timber. This method shall be considered as the reference method. This standard applies to sawn timber, and timber which has been planed or surfaced by other means.#,,#
Moisture content of a piece of sawn timber - Part 1: Determination by oven dry method; German version EN 13183-1:2002
Moisture content of a piece of sawn timber - Part 2 : estimation by electrical resistance method.
This European Standard defines a non-destructive method for estimating the moisture content of a piece of sawn timber using an electrical resistance moisture meter. This standard applies to sawn timber, and timber which has been planed or mechanically surfaced by other means.
Moisture content of a piece of sawn timber - Estimation by electrical resistance method
This European Standard defines the method for determining the moisture content of a piece of sawn timber. This method is considered as the reference method. This standard applies to sawn timber, and timber which has been planed or mechanically surfaced by other means.
Moisture content of a piece of sawn timber - Determination by oven dry method
This European Prestandard defines a destructive method of assessing the case-hardening of a piece of sawn timber with reference to the distortion measured in a slice taken from the piece. This European Prestandard is applicable to sawn timber and timber which has been planed or surfaced by other means. It applies to both hardwood and softwood with a thickness not greater than 100 mm.
Sawn timber - Methods for assessment of case-hardening
1.1 This test method is designed to evaluate the effectiveness of water-repellent compositions for retarding dimensional changes in coated wood submerged in water. It can also be used to measure the differential swelling of untreated wood when exposed to liquid water environments. The compositions tested are designed to be mixed until uniform and applied by brush, roller, dip or spray to an exterior wood surface.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Test Method for Anti-Swelling Effectiveness of Water-Repellent Formulations and Differential Swelling of Untreated Wood When Exposed to Liquid Water Environments
이 규격은 바닥 마무리 재료의 미끄럼 저항 계수를 흔들이식 바닥 미끄럼 시험기(이하 시험기
Method of test for floor slipperiness(Pendulum type)
이 규격은 경골 목조 전단벽의 전단 시험 방법에 대하여 규정하며 이 시험 방법에 규정한 것
Method of shear(racking) resistance test for light-frame wood shear walls
이 규격은 목조 건축을 비롯한 목구조용으로 사용되는 철물 관련 표준 용어에 대하여 규정한다
Standard terminology related to wood-Nails and fasteners for wood structures
이 규격은 원목과 제재목 관련 표준 용어에 대하여 규정한다.
Standard terminology related to wood-Log and sawn timber
To be read in conjunction with DD ENV 1995-1-1:1994
Wood-based panels - Characteristic values for structural design - OSB, particleboards and fireboards
This European standard gives a classification for solid wood panels and defines terms used with solid wood panels.
Solid wood panels - Classification and terminology
Specifies requirements for preservative-treated hardwood structural poles, agricultural poles, fencing poles, round droppers, guardrail posts and spacer blocks.
Wooden poles, droppers, guardrail posts and spacer blocks Part 3: Hardwood species
Criteria for the assessment of conformity of a lot of sawn timber
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号