B69 木材加工材 标准查询与下载

ASTM D25-99e1 圆木桩的标准规范

1.1 This specification covers the physical characteristics of unused round timber piles to be used either treated or untreated. 1.2 This specification is not intended for preused piles unless the piles have the quality specified by this specification and design stresses equal to or greater than those derived from Test Method D2899. 1.3 The values stated in inch-pound units are to be regarded as the standard.

Standard Specification for Round Timber Piles

ASTM D25-99 圆木桩的标准规范

1.1 This specification covers the physical characteristics of unused round timber piles to be used either treated or untreated. 1.2 This specification is not intended for preused piles unless the piles have the quality specified by this specification and design stresses equal to or greater than those derived from Test Method D2899. 1.3 The values stated in inch-pound units are to be regarded as the standard.

Standard Specification for Round Timber Piles

ISO 2067:1998 粒状软木 取样

This International Standard specifies a method for the sampling of granulated cork. As the characteristics of granulated cork have to be checked before any pressing is undertaken, this International Standard applies solely to loose granulated cork prior to any pressing, despatch from the silos, or packing in sacks.

Granulated cork - Sampling

ISO 2190:1998 粒状软木 含水量的测定

This International Standard specifies the reference method for determination of the moisture content of granulated cork. NOTE For the purposes of factory control, the manufacturer may choose another test method and/or different equipment. In this case, the co-relation between that method (current method) and the reference method should be established.

Granulated cork - Determination of moisture content

LY/T 1285-1998 船舶锯材

本标准规定了船舶锯材树种、尺寸、公差、缺陷限度及检验方法。 本标准适用于大中型船舶制造与维修。

Sawn timber for ship

BS EN 844-10:1998 圆木和锯木.术语.有关斑渍和真菌侵害的术语

This part of this standard defines terms relating to stain and fungal attack used in European Standards. The definitions in this part standard are intended for general commercial use. NOTE: In case of dispute, attention is drawn to the definitions given in standards prepared by CEN/TC 38 " Durability of wood and derived materials".

Round and sawn timber - Terminology - Terms relating to stain and fungal attack

BS EN 844-11:1998 圆木和锯木.术语.有关昆虫引起衰变的术语

This part of this standard defines terms relating to degrade by insects used in European Standards. The definitions in this part standard are for general commercial use. NOTE: In case of dispute, attention is drawn to the definitions given in standards prepared by CEN/TC 38 " Durability of wood and derived materials".

Round and sawn timber - Terminology - Terms relating to degrade by insects

ASTM D2555-98 制定纯净木料强度值的试验方法

1.1 These test methods cover the determination of strength values for clear wood of different species in the unseasoned condition, unadjusted for end use, applicable to the establishment of working stresses for different solid wood products such as lumber, laminated wood, plywood, and round timbers. Presented are: 1.1.1 Procedures by which test values obtained on small clear specimens may be combined with density data from extensive forest surveys to make them more representative, 1.1.2 Guidelines for the interpretation of the data in terms of assigned values for combinations of species or regional divisions within a species to meet special marketing needs, and 1.1.3 Information basic to the translation of the clear wood values into working stresses for different solid wood products for different end uses. 1.1.4 For species where density survey data are not as yet available for the reevaluation of average strength properties, the presently available data from tests made under the sampling methods and procedures of Methods D143, or Practice E105, are provided with appropriate provision for their application and use. Because of the comprehensive manner in which the density survey is undertaken, it follows that the reevaluated strength data are intended to be representative of the forest stand, or rather large forest subdivisions. 1.1.5 Some useful mechanical properties (tensile strengths parallel and perpendicular to grain and modulus of rigidity for a longitudinal-transverse plane) have not been extensively evaluated. Methods are described for estimating these properties by their relation to other properties. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Establishing Clear Wood Strength Values

ASTM D2555-98e1 制定纯净木料强度值的试验方法

1.1 These test methods cover the determination of strength values for clear wood of different species in the unseasoned condition, unadjusted for end use, applicable to the establishment of working stresses for different solid wood products such as lumber, laminated wood, plywood, and round timbers. Presented are:1.1.1 Procedures by which test values obtained on small clear specimens may be combined with density data from extensive forest surveys to make them more representative,1.1.2 Guidelines for the interpretation of the data in terms of assigned values for combinations of species or regional divisions within a species to meet special marketing needs, and1.1.3 Information basic to the translation of the clear wood values into working stresses for different solid wood products for different end uses.1.1.4 For species where density survey data are not as yet available for the reevaluation of average strength properties, the presently available data from tests made under the sampling methods and procedures of Methods D 143, or Practice E 105, are provided with appropriate provision for their application and use. Because of the comprehensive manner in which the density survey is undertaken, it follows that the reevaluated strength data are intended to be representative of the forest stand, or rather large forest subdivisions.1.1.5 Some useful mechanical properties (tensile strengths parallel and perpendicular to grain and modulus of rigidity for a longitudinal-transverse plane) have not been extensively evaluated. Methods are described for estimating these properties by their relation to other properties.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Establishing Clear Wood Strength Values

ISO 8507:1997 集成软木盘 试验方法

This International Standard specifies the test methods applicable to agglomerated cork discs intended to provide a tight closure in use with crown or screw caps.

Agglomerated cork discs - Test methods

BS EN 844-9:1997 圆木和锯木.术语.有关锯材特征的术语

This part standard defines terms relating to features of sawn timber used in European Standards.

Round and sawn timber - Terminology - Terms relating to features of sawn timber

BS EN 844-7:1997 圆木和锯木.术语.有关木材组织结构的术语

This part standard defines terms relating to the anatomical structure of timber used in European Standards.

Round and sawn timber - Terminology - Terms relating to anatomical structure of timber

BS EN 844-6:1997 圆木和锯木.术语.有关锯材尺寸测定的术语

This part standard defines terms relating to dimensions of sawn timber used in European Standards.

Round and sawn timber - Terminology - Terms relating to dimensions of sawn timber

BS EN 1312:1997 圆木材和板木材.锯材批量体积的测定

This standard specifies the rules for the determination of the batch volume of sawn timber. It applies to the volume of a batch of similar or dissimilar pieces of sawn softwood or hardwood. This standard applies to the following products defined in EN 844-3, for example: - rough-sawn timber (boules and square sawn); - regularized green timber; - regularized dried timber, - prepared timber, - planed timber; regardless of whether or not the timber meets the requirements of any dimensional or qualitative standards.

Round and sawn timber - Determination of the batch volume of sawn timber

BS EN 1309-1:1997 圆木和锯木.尺寸的测量方法.第1部分:锯木

Applies to hardwood and softwood sawn timber, both square edged and unedged, but does not apply to tropical timber.

Round and sawn timber - Method of measurement of dimensions - Sawn timber

DIN EN 1309-1:1997 圆木和锯木.尺寸测量方法.第1部分:锯木

The document specifies the methods of measuring dimensions of sawn timber. It applies to hardwood and softwood sawn timber, both square edged and unedged. The document does not apply to tropical timber.#,,#

Round and sawn timber - Method of measurement of dimensions - Part 1: Sawn timber; German version EN 1309-1:1997

DIN EN 844-8:1997 圆木和锯木.术语.第8部分:圆木特性术语

The document defines terms relating to features of round timber used in European Standards.

Round and sawn timber - Terminology - Part 8: Terms relating to features of round timber; German version EN 844-8:1997

DIN EN 1311:1997 圆木和锯木.病虫害侵蚀测定方法

Round and sawn timber - Method of measurement of biological degrade; German version EN 1311:1997

DIN EN 844-6:1997 圆木和锯木.术语.第6部分:锯木尺寸术语

The document defines terms relating to dimensions of sawn timber used in European Standards.

Round and sawn timber - Terminology - Part 6: Terms relating to dimensions of sawn timber; German version EN 844-6:1997

DIN EN 844-5:1997 圆木和锯木.术语.第5部分:圆木尺寸术语

The document defines terms relating to dimensions of round timber used in European Standards.

Round and sawn timber - Terminology - Part 5: Terms relating to dimensions of round timber; German version EN 844-5:1997