B70 人造板 标准查询与下载

DIN EN 12871:2013 木基板.地面、屋顶和墙体中使用的承载板的性能特征的测定.德文版本EN 12871-2013

Wood-based panels - Determination of performance characteristics for load bearing panels for use in floors, roofs and walls; German version EN 12871:2013

DB35/T 1352-2013 低密度纤维板

本标准规定了低密度纤维板的术语和定义、要求、测量和试验方法、检验规则、标志、包装、运输 和贮存。 本标准适用于木质纤维或其它植物纤维为原料制成的低密度纤维板。

low density fiberboard

NF B51-295:2013 人造板耐腐性试验方法（担子菌）

Wood-based panels - Test method for resistance to rot (Basidiomycetes fungi)

ISO 12466-1:2007/Amd 1:2013 胶合板.胶合质量.第1部分:试验方法.修改件1

Plywood - Bonding quality - Part 1: Test methods; Amendment 1

DIN EN 13442:2013 木地板和木镶板和贴面层. 耐化学剂的测定; 德文版本EN 13442-2013

Wood flooring and wood panelling and cladding - Determination of the resistance to chemical agents; German version EN 13442:2013

DIN EN 1910:2013 木地板和木镶板和贴面层. 尺寸稳定性的测定; 德文版本EN 1910-2013

Wood flooring and wood panelling and cladding - Determination of dimensional stability; German version EN 1910:2013

BS EN 1156:2013 人造板. 负荷保持时间和蠕变系数的测定

Wood-based panels. Determination of duration of load and creep factors

EN 1156:2013 人造板 载荷持续时间和蠕变系数的测定

This European Standard specifies a method of determining in a constant climate both a duration of load factor and a creep factor for wood-based panels stressed in flatwise bending with and without a shear component. Details of an alternative but provisional method employing medium sized test pieces are given in Annex A; this method can also be used for test pieces loaded under varying climates. NOTE The duration of load factor is necessary to modify the characteristic strength values obtained in short-term structural tests in order to derive long-term values. The creep factor obtained in the test is used to predict a long-term deflection from the initial elastic deflection.

Wood-based panels - Determination of duration of load and creep factors

LY/T 2141-2013 定向结构麦秸板

本标准规定了定向结构麦秸板的术语和定义、分类、要求、检验方法、结果计算及判定方法、检验规则、标志、包装、运输和贮存等。本标准适用于由规定形状的片状麦秸施胶后定向铺装压制成的多层定向结构麦秸板。

Oriented structural straw board

EN 1910:2013 木地板和木镶板-尺寸稳定性的测定

Wood flooring and wood panelling and cladding - Determination of dimensional stability

BS EN 636:2012 胶合板.规格

Plywood. Specifications

ANSI/ASTM D709:2013 层压热固性材料规范

Specification for Laminated Thermosetting Materials

PD CEN/TS 16526:2013 家具夹芯板(SWB-F).工厂制产品.性能特性测定的定义,分类和试验方法

This European Technical Specification defines terms, establishes a classification and specifies test methods for flat, factory made, non-structural, faced and unfaced sandwich boards for use in furniture manufacturing (SWB-F) for dry (service class 1) and humid conditions (service class 2). This European Technical Specification does not specify requirements. Guidance is provided for the selection of board properties which are relevant for specific board applications. This European Technical Specification is not applicable to products which are already covered by existing standards.

Sandwich boards for furniture (SWB-F) - Factory made products - Definition@ classification and test methods for determination of performance characteristics

ASTM D2719-13 胶合板纵向剪切的标准试验方法

3.1 The strength and modulus of rigidity of structural panels in shear through-the-thickness obtained by these test methods are required for the rigorous design of many lumber-panel structural components such as trusses with panel gussets, box beams, folded plate roofs, and space plane structures, as well as floor and roof diaphragms, and shear walls. These properties are of secondary importance in typical roof deck and sheathing applications, and in crates and shipping containers. 3.2 Veneer produced by slicing or rotary peeling may contain fine checks or separations parallel to the grain on the knife side of the veneer that are produced as the knife is forced through the wood. These checks are termed “knife checks” to distinguish them from occasional checks that may be formed on the opposite side of the veneer by forces at the compression bar, and from checks caused by drying. Average depth of knife checks has been found to strongly influence shear properties in plywood panels and may be of significance in veneer incorporated in composite panels. Measurement of depth of knife checks is recommended in these test methods. 3.3 To control or define other variables influencing shear properties, these test methods require determination of moisture content and elapsed time to failure. The conditioning of test material in controlled atmosphere and determination of specific gravity are recommended. 1.1 These test methods determine the shear through-the-thickness properties of structural panels associated with shear distortion of the major axis. Structural panels in use include plywood, oriented strand board, and composites of veneer and of wood based layers. Three test methods are included which differ somewhat in their application: 8199;8199;Test Method Section A. Small Panel Shear Test 5 B. Large Panel Shear Test 6 C. Two Rail Shear Test 7 The choice of test method will be determined in part by the purpose of the tests, characteristics of test material, and equipment availability. In general, Test Method B or C for large specimens is preferred when equipment, amount of test material, and experimental plan permit. 1.1.1 Test Method A: Small Panel Shear Test—This test method is suitable for testing small samples of uniform material including investigations of the effects of grain direction or orientation and of many raw materials and manufacturing process variables which influence shear properties uniformly throu......

Standard Test Methods for Structural Panels in Shear Through-the-Thickness

DIN EN 636:2012 胶合板.规格.德文版本EN 636-2012

This European Standard specifies the requirements for plywood,as defined in EN 313-2,for both general purpose use (non-structural application) and structural application in dry,humid or exterior conditions. It also gives a classification system based on the bending properties.

Plywood - Specifications; German version EN 636:2012

DB35/T 1250-2012 浸渍胶膜纸饰面胶合板

本标准规定了浸渍胶膜纸饰面胶合板的术语和定义、产品分类、要求、试验方法、检验规则以及标志、包装、运输和贮存。 本标准适用于以浸渍氨基树脂的胶膜纸铺装在胶合板基材表面，经热压而成的浸渍胶膜纸饰面胶合板。

Impregnated film paper facing plywood

NF B54-163:2012 胶合板.规格

Plywood - Specifications

DB32/ 2164-2012 纤维板单位产品综合能耗限额及计算方法

Comprehensive energy consumption limit and calculation method of fiberboard unit product

DIN ISO 3034:2012 波纹纤维板. 单张厚度的测定 (ISO 3034-2011)

Corrugated fibreboard - Determination of single sheet thickness (ISO 3034:2011)

NF B51-274:2012 木基板材. 甲醛释放的测量. 干燥器法.

Wood based panels - Determination of formaldehyde release - Dessicator method.