C66 安全控制技术 标准查询与下载

DIN EN 358:2000 控制工作位置和防止从高处坠落的人员防护设备.工作定位、约束和工作用的安全带和牵索

The document applies to belts and lanyards intended for the purpose of work positioning of restraint. It specifies the requirements, testing, marking and information supplied by the manufacturer.

Personal protective equipment for work positioning and prevention of falls from a height - Belts for work positioning and restraint and work positioning lanyards; German version EN 358:1999

ASTM F2049-00 公共、商用和多家庭住宅户外游戏场所用栅栏的标准指南

1.1 This guide provides the recommended minimum requirements for denoting various types of fences/barriers for the protection of children's outdoor play spaces in public, commercial, and multi-family residential use locations. This guide excludes individual single family residential use play equipment locations.1.2 This guide provides for the safety of occupants in play areas or zones as it pertains to vehicular intrusion as well as other participant intrusion, and for children containment or entry/exit.1.3 This guide does not purport to address the aspect of safety within a play area or zone. It is the responsibility of the user of this guide to establish appropriate safety practices as related to the play area and determine the applicability of regulatory requirements prior to use.1.4 This guide does not choose the product components for the fence system, the choice of which should be made by the operators of the play space and their specification writers or drafters based upon their determination of the merits of the products that could be used.1.5 The values stated in inch-pound units are to be regarded as standard. The SI values given in parentheses are for information only.

Standard Guide for Fences/Barriers for Public, Commercial, and Multi-Family Residential Use Outdoor Play Areas

ISO 16107:1999 车间空气 扩散型采样器性能评估协议

1 This International Standard covers the evaluation of the performance of diffusive samplers of gases and vapours for use over sampling periods from 4 h to 12 h. Sampling periods of such duration are the most common in workplace sampling. Given a suitable exposure chamber, this International Standard can be straightforwardly extended to cover samplers for use over other sampling periods as well. The aim is to provide a concise set of experiments for classifying samplers primarily according to a single numerical value representing sampler accuracy. NOTE Accuracy estimates refer to conditions of sampler use which are normally expected in a workplace setting. These conditions may be characterized by the temperature, atmospheric pressure, humidity and ambient wind speed, none of which may be constant or accurately known. Furthermore, the accuracy accounts for difficulty in the estimation of time-weighted averages of concentrations which may not be constant in time. In addition to accuracy determination, a method is provided to test the samplers for compliance with the manufacturer's stated limits on capacity, possibly in the presence of interfering compounds. A method is given for classification of samplers according to their capability to detect situations in which sampler capacity may be exceeded. 2 This International Standard is an extension of previous research on diffusive samplers [1-17] as well as EN 838. Essential advantages are the estimation of sampler accuracy under actual conditions of use and the reduction in cost of sampler evaluation. NOTE Furthering the latter point, knowledge of similarity between analytes of interest can be used to expedite sampler evaluation. For example, interpolation of data characterizing the sampling of analytes at separated points of a homologous series of compounds is recommended. At present the procedure in [9] is suggested: Following evaluation of a sampler in use at a single homologous series member according to the present practice, higher molecular weight members would receive partial validations considering sampling rate, capacity, analytical recovery and interferences.

Workplace atmospheres - Protocol for evaluating the performance of diffusive samplers

EN 12786:1999 机械安全性.安全标准振动条款的起草指南

Thii European Standard gives guidance on how to deal with vibration in type Gstandards where vibration is identified as a significant hazard (see 4.6 of EN 292-1:1991). As such, this European Standard supplements the niles given in EN 414. The exact way that vibration is deait with for particular machinery will depend on the structure of the type C-standards and is the responsibility of the type C-standards Technical Committees.

Safety of Machinery - Guidance for the Drafting of the Vibration Clauses of Safety Standards

DIN EN 61229/A1:1999 交流设备上带电作业用的刚性保护罩.修正A1

Rigid protective covers for live working on a.c. installations; Amendment A1 (IEC 61229:1993/A1:1998); German version EN 61229:1995/A1:1998

ISO 14567:1999 防止从高处坠落的个人防护装置 单点锚定设备

This International Standard specifies requirements, test methods, and marking, labelling and packaging, as appro-priate, of both permanent and temporary single-point anchor devices exclusively for the attachment of personal protective equipment (PPE) for protection against falls from a height for fall arrest, work positioning and travel restriction (work restraint). It is applicable only to anchor devices for PPEs that conform to ISO 10333-1, ISO 10333-2, ISO 10333-3 and ISO 10333-5. NOTE 1 Further standards are in preparation for other types of PPE: ISO 10333-6 and ISO 14566 (see bibliography). Anchor devices are rated to sustain a maximum (dynamic) arresting force of 6,0 kN, and a maximum (static) loading of 1,0 kN (assuming a person of 100 kg mass) in post-fall arrest suspension, work-positioning mode, or restraint mode. Anchor devices are intended for single person use only. A rescuer should not attach to the same anchor device as a person being rescued, unless the anchor device has been specifically designed for such purposes, and the instructions for use specifically permit this application. NOTE 2 Vertical rigid or flexible line systems and horizontal lifelines are not within the scope of this International Standard, but are covered in ISO 10333-4 and ISO 16024.

Personal protective equipment for protection against falls from a height - Single-point anchor devices

BS EN 1891:1998 防高处坠落个人保护设备.低弹力纤维绳索

This European Standard applies to low stretch textile ropes of kernmantel construction from 8,5 mm to 16 mm diameter, for use by persons in rope access including all kinds of work positioning and restraint; for rescue and in speleology. Two types of low stretch kernmantel rope are defined: A and B. The European Standard specifies requirements, testing, marking and information to be supplied by the manufacturer including instructions for use of such low stretch kernmantel ropes. NOTE 1 It is possible that rope not conforming to this European Standard may also be suitable for the activities described above. NOTE 2 Ropes used for protection during any free climbing activity in rope access, rescue or speleology should take account of other standards, e.g. EN 892. Dynamic mountaineering rope may also be used for protection during rope access and work positioning.

Personal protective equipment for the prevention of falls from a height - Low stretch kernmantel ropes

SJ/T 11159-1998 地板覆盖层和装配地板静电性能的试验方法

本标准是IEC 1340-4系列标准之一，规定了表征地板覆盖层和装配地板静电性能的电阻起电性的测量方法。由于使用的要求，需要不同类型的地板，利用电阻测量方法不可能充分地表征静电的性能。所以起电性测量方法的建立是必要的。 这些方法适用于供各种类型的地板覆盖层和装配地板的试验使用。地板覆盖层的测试在受控环境条件下的试验室内进行，并在经受条件处理试验后进行。对于装配地板，其测量在非受控环境条件下的现场进行。 对于控制静电用的材料来说，按本标准所规定的要求进行试验是适当的，测量也可以在导电性更好或绝缘性更好的材料上进行。

Test methods for electrostatic behaviour of floor coverings and installed floors

BS EN 1760-1:1997+A1:2009 机械的安全性.压力敏感防护装置.压力敏感垫和压力敏感地板的设计和试验用通用原理

This Standard specifies requirements for pressure sensitive mats and floors normally actuated by the feet for use as safety devices to protect persons from dangerous machinery. The minimum safety requirements for the performance, marking and documentation are given. The Standard covers pressure sensitive mats and floors, regardless of type of energy used, e.g. electrical, hydraulic, pneumatic or mechanical. This standard covers mats and floors designed to detect: a) Persons weighing more than 35 kg; b) And persons (e.g. children) weighing more than 20 kg. The detection of persons weighing less than 20 kg is not covered by this standard. This European Standard does not specify the dimensions or the configuration of the effective sensing area of pressure sensitive mat(s) or floor(s) in relation to any particular application.

Safety of machinery - Pressure sensitive protective devices - General principles for the design and testing of pressure sensitive mats and pressure sensitive floors

IEC 60825-4:1997 激光产品的安全 第4部分:激光防护器

This part of IEC 60825 specifies the requirements for laser guards, permanent and temporary (for example for service), that enclose the process zone of a laser processing machine, and specifications for proprietary laser guards. This standard applies to all component parts of a guard including clear (visibly transmitting) screens and viewing windows, panels, laser curtains and walls. Requirements for beam path components, beam stops and those other parts of a protective housing of a laser product which do not enclose the process zone are contained in IEC 60825-1. In addition this part of IEC 60825 indicates: a) how to assess and specify the protective properties of a laser guard; and b) how to select a laser guard.

Safety of laser products - Part 4: Laser guards

BS EN 795:1997 防止从高处跌落.抛锚设备.要求性和试验

This standard specifies requirements, test methods and instructions for use and marking for anchor devices designed exclusively for use with personal protective equipment against falls from a height. This standard does not apply to hooks designed to EN 517 or walkways to EN 516, nor to fixed anchor points forming part of the original structure.

Protection against falls from a height. Anchor devices. Requirements and testing

DIN EN 61229:1997 在交流设备上带电作业用刚性保护罩

Rigid protective covers for live working on a.c. installations (IEC 61229:1993, modified); German version EN 61229:1995

ANSI/ASTM D4509:1997 新吹净PET(生产环境测试)瓶的24小时气室乙醛含量测定方法

These test methods cover the 24-h gas-space acetaldehyde (AA) content of freshly blown polyethylene terephthalate (PET) bottles. These test methods, containing internal or external standard calibration, are applicable to all PET bottles. The values stated in SI units are to be regarded as the standard. Note 1- These is no similar or equivalent ISO standard. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Test Methods for Determining the 24-Hour Gas (Air) Space Acetaldehyde Content of Freshly Blown PET Bottles

ANSI/ASTM F1270:1997 应急部署表编制和定位的实施规程

Practice for Preparing and Locating Emergency Muster Lists

BS EN 626-2:1996+A1:2008 机械安全.降低机械排放的有害物质对健康的危害.鉴定程序用方法学

This standard defines a procedure which leads to the selection of critical factors relating to emissions of hazardous substances for the purpose of specifying suitable verification procedures. This standard is to be used in conjunction with EN 626-1.

Safety of machinery - Reduction of risk to health from hazardous substances emitted by machinery - Part 2: Methodology leading to verification procedures

NF P95-311:1996 雪崩防护设备 人工触发 爆炸承载电缆

Équipements de protection contre les avalanches - Déclenchement artificiel - Câble transporteur d'explosif.

NF P95-310:1996 雪崩防护设备-人工释放-通用技术原理

Équipements de protection contre les avalanches - Déclenchement artificiel - Principes techniques généraux.

ISO 13854:1996 机械安全 避免人体部分挤压的最小间距

Purpose is to enable the user (e.g. standard makers, designers of machinery) to avoid hazards from crushing zones. Specifies minimum gaps relative to parts of the human body. Applicable when adequate safety can be achieved by this method.

Safety of machinery - Minimum gaps to avoid crushing of parts of the human body

BS EN 1088:1995+A2:2008 机械的安全性.带防护装置的连锁装置.设计和选择的原则

This standard specifies principles for the design and selection - independent of the nature of the energy source – of interlocking devices associated with guards (as defined in 3.23.1 "interlocking device [interlock]", 3.22.4 "interlocking guard" and 3.22.5 "interlocking guard with guard locking" of EN 292-1:1991). It also provides requirements specifically intended for electrical interlocking devices (see clause 6). This standard covers the parts of guards which actuate interlocking devices. Requirements for guards are given in prEN 953. The processing of the signal from the interlocking device to stop and immobilize the machine is dealt with in prEN 954-1.

Safety of machinery — Interlocking devices associated with guards — Principles for design and selection

BOCA CHAPTER 33 NFPC-1996 易燃固体

The provisions requiring that the excavation left when an unfit structure has been removed be filled in is an obvious, but often neglected means of protecting the public health and safety.

Flammable Solids