D98 煤矿专用设备器材 标准查询与下载

MT/T 705-2007 煤矿用隔爆型低压插销

Flameproof low-voltage plug for coal mines

MT/T 706-2007 一般兼矿用本质安全型安全栅

General and mining intrinsically safe safety barrier

AQ 6207-2007 便携式载体催化甲烷检测报警仪

本标准规定了便携式载体催化甲烧检测报警仪（以下简称“报警仪”）的技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于使用载体催化原理的在煤矿井下具有爆炸性气体环境中使用的便携式甲烷检测报警仪。

Portable Carrier Catalytic methane alarm detector

BS EN 62013-2:2006 对沼气敏感的矿工用头灯.性能和其他相关安全问题

This part of IEC 62013 details those performance and other safety features of caplights, including those with a point of connection for another apparatus, not covered in IEC 62013-1, but which are important for the safety and working conditions of the user. It may also be applied to caplights for use in mines not likely to be endangered by firedamp. When this part of the standard is used as a "stand-alone" document for non-gassy mines, any relevant constructional requirements should be the subject of agreement between the supplier and the user and, where possible, be as described in IEC 62013-1.

Caplights for use in mines susceptible to firedamp - Performance and other safety-related matters

MT/T 247-2006 采掘机械用齿座

本标准规定了采掘机械用齿座（以下简称齿座）的产品分类、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于煤矿采煤机、掘进机使用的齿座。

Pick holder for shearer and boom roadheader

MT/T 246-2006 采掘机械用截齿

本标准规定了采掘机械用截齿（以下简称截齿）的术语和定义、产品分类、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于截割坚固性系数f不大于6（单向抗压强度不大于60MPa）的煤和夹矸的煤矿采煤机、掘进机使用的截齿。

Pick for shearer and boom roadheader

MT/T 994-2006 矿用手持式气动钻机

本标准规定了矿用手持式气动钻机（以下简称钻机）的术语和定义、钻机型号和基本性能参数、技术要求、试验方法、检验规则以及标志、包装、运输和贮存。 本标准适用于矿用手持式气动钻机，也适用于矿用手持式回转类气动工具，并可供矿用非手持式气动回转类机具参考使用。

Hand-held pneumatic rotary drill in coal mine

MT 990-2006 矿用防爆柴油机通用技术条件

本标准规定了矿山井下用防爆柴油机（以下简称柴油机）的技术要求、试验方法、检验规则及标志、包装、运输和贮存。 本标准适用于具有爆炸性气体环境的矿山井下使用的防爆柴油机及其附属配套部件。

The general technical condition of the flameproof diesel engine for the mine

MT/T 455-2006 矿灯充电架型号编制方法

本标准规定了矿灯充电架（以下简称充电架）型号的编制原则、型号的组成和排列方式、编制方法和管理及申报办法。 本标准适用于煤矿地面室内用的充电架，不适用于单个矿灯充电器。

Method of type symbolization for cap lamp charger

MT/T 154.6-2006 矿灯型号编制方法

本标准规定了矿灯型号的编制原则、型号的组成和排列方式、编制方法和管理及申报办法。

Method of type symbolization for cap lamp

BS EN 1710:2005 地下矿井潜在爆炸性环境用设备和组件

This European Standard specifies the explosion protection requirements for the construction and marking of equipment that may be an individual item or form an assembly. This includes machinery and components placed on the market by a single supplier for use in mines susceptible to explosive atmospheres of firedamp and/or combustible dust (at atmospheric conditions as defined in EN 1127-2). NOTE 1 This European Standard deals only with the ignition protection of mining machinery and manufacturers will need to take account of all other relevant EU Directives relating to the construction of machines e.g. the consolidated Machinery Directive 98/37/EC. Additionally, manufacturers will need to take account of any national legislation in the country where they intend to market their equipment. NOTE 2 Where the flammable gas in the atmosphere is not predominantly methane, reference will need to be made to 4.1 in either EN 60079-0:2004 or EN 13463-1:2001. NOTE 3 The definition of ‘equipment’ is contained in EN 13463-1. The definition of ‘assembly’ can be found the ATEX guidelines, published by the European Commission. Equipment complying with the relevant clauses of this European Standard is considered to meet the requirements for equipment of Group I - Category M2. This European Standard also deals with the prevention of ignitions of explosive atmospheres caused by burning (or smouldering) of combustible material such as fabric fibres, plastic ”O”-rings, rubber seals, lubricating oils or greases used in the construction of the equipment if such items could be an ignition source. For example, the mechanical failure of rotating shaft bearings can result in frictional heating that ignites its plastic cage, plastic seal or lubricating grease. See also 5.2.4 of EN 13463-1:2001. NOTE 4 The above clause of EN 13463-1 requires the ignition hazard assessment to include those components which, if they failed, could ignite any flammable substance (e.g. lubricating oil) contained within the equipment and which could consequently become, or create, an ignition source. In the case of coal mining equipment and components, the ignition temperature of the mineral oils or greases used is often below that of firedamp, i.e. below 560 °C.

Equipment and components intended for use in potentially explosive atmospheres in underground mines

MT/T 1008-2006 煤矿安全生产监控系统软件通用技术要求

本标准规定了煤矿安全生产监控系统软件产品（以下简称软件）的术语和技术要求。 本标准适用于煤矿安全生产监控系统软件产品。

General technical requirements of software for productive safety supervision system in coal mine

MT/T 1007-2006 矿用信息传输接口

本标准规定了矿用信息传输接口的产品分类、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于煤矿使用的矿用信息传输接口（以下简称接口）。

Information transmission interface for coal mine

MT/T 1006-2006 矿用信号转换器

本标准规定了矿用信号转换器的产品分类、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于煤矿使用的矿用信号转换器(以下简称转换器)。

Signal converter for coal mine

MT/T 1005-2006 矿用分站

本标准规定了矿用分站的产品分类、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于煤矿使用的矿用分站（以下简称分站）。

Substation for coal mine

MT/T 1004-2006 煤矿安全生产监控系统通用技术条件

本标准规定了煤矿安全生产监控系统的术语和定义、产品分类、技术要求、试验方法、检验规则。 本标准适用于煤矿使用的煤矿安全生产监控系统（以下简称系统）。

General technical conditions of coal mine productive safety supervision system

MT/T 978-2006 矿用隔爆型硫化机

本标准规定了矿用隔爆型硫化机（以下简称硫化机）的分类、要求、试验方法、检验规则、标志、包装、运输及贮存。 本标准适用于煤矿井下用隔爆型电加热式硫化机。

Explosion proof vulcanizer for coal mine

MT/T 973-2006 钢绞线液压剪

本标准规定了钢绞线液压剪（以下简称液压剪）的术语和定义、型式与基本参数、技术要求、试验方法、检测规则和标志、包装、运输及贮存。 本标准适用于剪切矿用锚索钢绞线的液压剪，也适用于剪切其他钢绞线用液压剪。

Hydraulic cutter for steel wire strands

MT/T 827-2005 煤矿机械液压系统通用技术条件

本标准规定了煤矿机械液压系统设计和制造的通用技术条件。 本标准适用于以液压油（液）为工作介质，公称压力不高于31.5 Mpa 的煤矿机械设备的液压系统。

Coal mining machine hydraulic fluid power-General rules relating to system

MT/T 671-2005 煤矿用隔爆型潜水电泵

本标准规定了煤矿用隔爆型潜水电泵（以下简称电泵）的型式与基本参数、技术要求、试验方法、检验规则以及标志、包装、运输和贮存。 本标准适用于煤矿用隔爆型潜水电泵。

Flameproof submerge electric pump for coal mine