E43 石油沥青 标准查询与下载

ASTM D6084/D6084M-13 用延度仪测定沥青弹性回复的标准试验方法

3.1 This test method is useful in confirming that a material has been added to the asphalt to provide a significant elastomeric characteristic. It does not necessarily identify the type or amount of material added. 1.1 This test method assesses the elastic recovery of an asphalt material measured by the recoverable strain determined after severing an elongated briquet specimen of the material of the form described in 4.1. The specimens are pulled to a specified distance at a specified speed and at a specified temperature. Unless otherwise specified, the test shall be made at a temperature of 25 ± 0.5°C [77 ± 0.9°F] and with a speed of 5 cm/min ± 58201;%. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 Warning—Mercury has been designated by the United States Environmental Protection Agency and many state agencies as a hazardous material that can cause central nervous system, kidney and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable Material Safety Data Sheet (MSDS) for details and EPA’s website (http://www.epa.gov/mercury/index.htm) for additional information. Users should be aware that selling mercury and/or mercury containing products into your state may be prohibited by state law. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Elastic Recovery of Bituminous Materials by Ductilometer

ASTM D4402/D4402M-13 利用旋转粘度计测定高温下沥青粘度的标准试验方法

5.1 This test method is used to measure the apparent viscosity of asphalts at handling, mixing, or application temperatures. 5.2 Some asphalts may exhibit non-Newtonian behavior under the conditions of this test method, or at temperatures within the range of this test method. Since non-Newtonian viscosity values are not absolute properties, but reflect the behavior of the fluid within the particular measurement system, it should be recognized that measurements made by this test method may not always predict field performance under the conditions of use. 5.3 Comparisons between non-Newtonian viscosity values should be made only for measurements made with similar conditions of temperature, shear rate, and shear history. 1.1 This test method outlines a procedure for measuring the apparent viscosity of asphalt from 38 to 260°C [100 to 500°F] using a rotational viscometer and a temperature-controlled thermal chamber for maintaining the test temperature. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See 10.6 for specific precautionary information.

Standard Test Method for Viscosity Determination of Asphalt at Elevated Temperatures Using a Rotational Viscometer

ASTM D95-13e1 蒸馏法测定石油产品及沥青材料中水的试验方法

5.1 A knowledge of the water content of petroleum products is important in the refining, purchase, sale, and transfer of products. 5.2 The amount of water as determined by this test method (to the nearest 0.05 or 0.1 volume8201;%, depending on the trap size used) may be used to correct the volume involved in the custody transfer of petroleum products and bituminous materials. 5.3 The allowable amount of water may be specified in contracts. 1.1 This test method covers the determination of water in the range from 0 to 258201;% volume in petroleum products, tars, and other bituminous materials by the distillation method. Note 1—Volatile water-soluble material, if present, may be measured as water. 1.2 The specific products considered during the development of this test method are listed in Table 8201;1. For bituminous emulsions refer to Test Method D244. For crude oils, refer to Test Method D4006 (API MPMS Chapter 10.2).Note 2—With some types of oil, satisfactory results may be obtained from Test Method D1796 (API MPMS Chapter 10.6). 1.3 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 6.

Standard Test Method for Water in Petroleum Products and Bituminous Materials by Distillation

DIN CEN/TS 16346:2012 沥青和沥青粘合剂. 带2/4 mm 聚集体的阳离子沥青乳剂的断裂特性和直接粘附性的测定; 德文版本CEN/TS 16346-2012

Bituminous binders - Determination of breaking behaviour and immediate adhesivity of cationic bituminous emulsions with 2/4 mm aggregate; German version CEN/TS 16346:2012

DB14/T 677-2012 公路抗车辙沥青混合料设计与施工技术规范

Technical specification for design and construction of road rutting-resistant asphalt mixture

DB14/T 676-2012 嵌挤密实型沥青混合料组成设计规程

Code for composition design of embedded compact asphalt mixture

NF P98-818-40:2012 沥青混合物 - 热混沥青的试验方法 - 第40部分: 现场排水能力

Bituminous mixtures - Test methods for hot mix asphalt - Part 40: in situ drainability

DIN EN 12697-3:2012 沥青混合物.热混合沥青的试验方法.第3部分:沥青回收.旋转式蒸发器.德文版本FprEN 12697-3-2012

Bituminous mixtures - Test methods for hot mix asphalt - Part 3: Bitumen recovery: Rotary evaporator; German version FprEN 12697-3:2012

NF P98-818-39:2012 沥青混合物 - 热混沥青的试验方法 - 第39部分: 用点燃法测定粘合剂含量.

Bituminous mixtures - Test methods for hot mix asphalt - Part 39 : binder content by ignition.

NF T66-054*NF EN 16345:2012 沥青和沥青粘合剂.使用雷氏粘度II号黏度计测定沥青乳液的排出时间

Bitumen and bituminous binders -Determination of efflux time of bituminous emulsions using the Redwood No. II Viscometer.

NF P98-818-21:2012 沥青混合物.热混沥青的试验方法.第21部分:使用板材样本的压痕

Bituminous mixtures - Test methods for hot mix asphalt - Part 21 : indentation using plate specimens.

NF P98-818-19:2012 沥青混合物.热混沥青的试验方法.第19部分:试样渗透性

Bituminous mixtures - Test methods for hot mix asphalt - Part 19 : permeability of specimen.

NF P98-818-30:2012 沥青混合物.热混沥青的试验方法.第30部分:使用冲击压实机的样品制备

Bituminous mixtures - Test methods for hot mix asphalt - Part 30 : specimen preparation by impact compactor.

DIN EN 12697-1:2012 沥青混合物. 热混沥青的试验方法. 第1部分:可溶粘合剂含量; 德文版本EN 12697-1-2012

Bituminous mixtures - Test methods for hot mix asphalt - Part 1: Soluble binder content; German version EN 12697-1:2012

DIN EN 12697-40:2012 沥青混合料.热混沥青的试验方法.第40部分:现场排水能力.德文版本EN 12697-40-2012

Bituminous mixtures - Test methods for hot mix asphalt - Part 40: In situ drainability; German version EN 12697-40:2012

BS EN 12697-40:2012 沥青混合料.热混沥青试验方法.现场排水能力

Bituminous mixtures. Test methods for hot mix asphalt. In situ drainability

BS EN 12697-39:2012 沥青混合料.热混沥青的试验方法.燃烧法测定粘合剂含量

Bituminous mixtures. Test methods for hot mix asphalt. Binder content by ignition

BS EN 12697-34:2012 沥青混合料.热混沥青混合料的试验方法.马歇尔试验

Bituminous mixtures. Test methods for hot mix asphalt. Marshall test

BS EN 12697-1:2012 沥青混合料.热混沥青的试验方法.可溶粘合剂含量

Bituminous mixtures. Test methods for hot mix asphalt. Soluble binder content

NF P98-818-34:2012 沥青混合物.热混沥青的试验方法.第34部分:马歇尔(Marshall)试验

Bituminous mixtures - Test methods for hot mix asphalt - Part 34 : Marshall test.