E43 石油沥青 标准查询与下载

ASTM D2170/D2170M-10 沥青的运动粘度的标准试验方法

The kinematic viscosity characterizes flow behavior. The method is used to determine the consistency of bitumen as one element in establishing the uniformity of shipments or sources of supply. The specifications are usually at temperatures of 60 and 135°C. 1.1 This test method covers procedures for the determination of kinematic viscosity of liquid asphalts (bitumens), road oils and distillation residues of liquid asphalts (bitumens) all at 60°C [140°F] and of asphalt cements at 135°C [275°F] (Note 1) in the range from 6 to 100 000 mm2/s [cSt]. 1.2 Results of this test method can be used to calculate viscosity when the density of the test material at the test temperature is known or can be determined. See Annex A1 for the method of calculation. Note 18212;This test method is suitable for use at other temperatures and at lower kinematic viscosities, but the precision is based on determinations on liquid asphalts and road oils at 60°C [140°F] and on asphalt cements at 135°C [275°F] only in the viscosity range from 30 to 6000 mm2/s [cSt]. 1.3 Warning8212;Mercury has been designated by United States Environmental Protection Agency (EPA) and many state agencies as a hazardous material that can cause central nervous system, kidney and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPA’s websitehttp://www.epa.gov/mercury/faq.htmfor additional information. Users should be aware that selling mercury, mercury containing products, or both, in your state may be prohibited by state law. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Kinematic Viscosity of Asphalts (Bitumens)

DB65/T 3044-2009 天然沥青

Natural Asphalt

YB/T 5300-2009 沥青焦真比重的测定方法

Method for determination of true specific gravity of pitch coke

YB/T 5298-2009 沥青焦试样的采取和制备方法

本标准规定了沥青焦试样采取和制备的术语和定义，采样和制备工具，采样方法和试样制备。 本标准适用于从煤焦油中所得的煤沥青(软沥青)，经延迟焦化后制得的沥青焦试样的采取和 制备。

Pitch coke sample collection and preparation method

DIN EN 15322:2009 沥青和沥青粘合剂.阳离子沥青乳液规定框架,德文版本:EN 15322:2009

This document provides a framework for specifying cut-back and fluxed bituminous binders which are suitable for the use in the construction and maintenance of roads, airfields and other paved areas. This document applies to un-modified and polymer modified bituminous cut-back and fluxed materials

Bitumen and bituminous binders - Framework for specifying cut-back and fluxed bituminous binders; English version of DIN EN 15322:2009-11

BS EN 15322:2009 沥青和沥青粘合剂.软制沥青和稀释沥青粘合剂的规定框架

This document provides a framework for specifying cut-back and fluxed bituminous binders which are suitable for the use in the construction and maintenance of roads, airfields and other paved areas. This document applies to un-modified and polymer modified bituminous cut-back and fluxed materials.

Bitumen and bituminous binders - Framework for specifying cut-back and fluxed bituminous binders

BS EN 12591:2009 沥青和沥青粘合剂.铺路级沥青规范

This European Standard provides a framework for specifying a range of properties and relevant test methods for bitumens, which are suitable for use in the construction and maintenance of roads, airfields and other paved areas, together with requirements for evaluation of conformity. This European Standard does not directly address ‘cohesion, adhesion and setting ability’ (see Introduction). NOTE Although industrial bitumens are specified according to EN 13305, it should be underlined that paving grade bitumens, specified according to this European Standard, can also be used for industrial applications.

Bitumen and bituminous binders - Specifications for paving grade bitumens

BS EN 12847:2009 沥青和沥青胶粘剂.测定沥青乳液的沉降倾向

This European Standard specifies a method for the determination of the settling tendency of bituminous emulsions.

Bitumen and bituminous binders - Determination of settling tendency of bituminous emulsions

BS EN 13075-2:2009 沥青和沥青粘合剂.断裂行为的测定.第2部分:阳离子沥青乳液细粒混合时间的测定

This European Standard specifies a method for the determination of the fines mixing time of diluted cationic bituminous emulsions, under standardized conditions.

Bitumen and bituminous binders - Determination of breaking behaviour - Part 2:Determination of fines mixing time of cationic bitumen emulsions

DIN EN 13303:2009 沥青和沥青粘合剂.工业沥青加热后质量损失的测定.英文版本DIN EN 13303-2009-07

This European Standard specifies a method for the determination of the loss in mass of industrial bitumen after heating. The method is used to detect volatile components. NOTE The users of the method are encouraged to gather comparative information on binders using this standard, EN 13303 and EN 12607-2 at 163 ℃ to facilitate the withdrawal of EN 13303 at the next systematic review.

Bitumen and bituminous binders - Determination of the loss in mass after heating of industrial bitumen; English version of DIN EN 13303:2009-07

DIN EN 13304:2009 沥青和沥青粘合剂.氧化沥青规范的框架.英文版本DIN EN 13304-2009-07

This European Standard provides a framework for the specification of oxidised bitumens used mainly in roofing, waterproofing, adhesives and thermal and phonic insulations. Within Europe several types of oxidised bitumens are used and, dependent on climatic conditions, type of building construction and traditional practices, different grades may be used for the same purpose. The framework given in this European standard provides a basis for quality agreements to be established between supplier and client. The oxidised bitumen products are graded by a combination of the values of ring and ball softening point, and penetration at 25 ℃, expressed as multiples of 5.

Bitumen and bituminous binders - Framework for specification of oxidised bitumens; English version of DIN EN 13304:2009-07

DIN EN 13075-1:2009 沥青和沥青粘合剂.断裂性能测定.第1部分:阳离子沥青乳液断裂值的测定.矿物填料法.英文版本DIN EN 13075-1-2009-07

This European Standard specifies a method for the determination of the breaking value of cationic bituminous emulsions.

Bitumen and bituminous binders - Determination of breaking behaviour - Part 1: Determination of breaking value of cationic bituminous emulsions, mineral filler method; English version of DIN EN 13075-1:2009-07

DIN EN 1430:2009 沥青和沥青粘合剂.沥青乳剂粒子极性的测定.英文版本DIN EN 1430-2009-07

This European Standard specifies a method for the determination of the particle polarity of bituminous emulsions.

Bitumen and bituminous binders - Determination of particle polarity of bituminous emulsions; English version of DIN EN 1430:2009-07

DIN EN 15626:2009 沥青和沥青粘合剂.用水浸入试验测定稀释和软制沥青粘合剂的粘合性.集料法

This document specifies a method for the determination of the adhesivity of cut-back and fluxed bituminous binders coated onto aggregate when immersed in water.

Bitumen and bituminous binders - Determination of adhesivity of cut-back and fluxed bituminous binders by water immersion test - Aggregate method; German version EN 15626:2009

DIN EN 12847:2009 沥青和沥青粘合剂.测定沥青乳液的凝固性,DIN EN 12847:2009-07的英文版本

This European Standard specifies a method for the determination of the setting tendency of bituminous emulsions.

Bitumen and bituminous binders - Determination of settling tendency of bituminous emulsions; English version of DIN EN 12847:2009-07

DIN EN 1431:2009 沥青和沥青粘合剂.用蒸馏法测定沥青乳液蒸馏的再生粘合剂和蒸馏油,DIN EN 1431:2009-07的英文版本

This European Standard specifies a method for the quantitative determination of residual binder and oil distillate in bituminous emulsions. The method can also be used to obtain residue and oil distillate for further testing. NOTE The properties of the material recovered in the test are not necessarily the same as those of the original materials from which the emulsion was produced, especially for polymer modified bitumens.

Bitumen and bituminous binders - Determination of residual binder and oil distillate from bitumen emulsions by distillation; English version of DIN EN 1431:2009-07

DIN EN 12850:2009 沥青和沥青粘合剂.测定沥青乳液的pH值,DIN EN 12850:2009-07的英文版本

This European Standard specifies a method for measuring the pH value of bituminous emulsions. It is applicable to anionic, cationic bituminous emulsions and bituminous emulsions prepared by means of non - ionic surfactant. NOTE In certain circumstances, the pH value can provide an indication of the ionic character of a bitumen emulsion. However, this indication should be confirmed by a particle polarity test conforming to EN 1430.

Bitumen and bituminous binders - Determination of the pH value of bituminous emulsions; English version of DIN EN 12850:2009-07

DIN EN 13305:2009 沥青和沥青粘合剂.硬质工业沥青的规范框架.英文版本DIN EN 13305-2009-07

This European Standard provides a framework for the specification of hard industrial bitumens used mainly in flooring, varnishes, mineral rubber, roofing and mastic. Within Europe several types of hard industrial bitumen are used, and dependent upon traditional practices, different grades may be used for the same purpose. The framework given in this European standard provides a basis for quality agreements to be established between supplier and client. The hard industrial bitumen products are graded by the limits of the ring and ball softening point values, expressed as multiples of 5, and are characterised by an H in front of the values.

Bitumen and bituminous binders - Framework for specification of hard industrial bitumens; English version of DIN EN 13305:2009-07

DIN EN 12848:2009 沥青和沥青粘合剂.沥青乳化液混凝土混的混合稳定性的测定,DIN EN 12848:2009-07的英文版本

This European Standard specifies a method for the determination of mixing stability of bituminous emulsions with cement. It applies to overstabilized cationic bituminous emulsions and to slow-setting and overstabilized anionic bituminous emulsions.

Bitumen and bituminous binders - Determination of mixing stability with cement of bituminous emulsions; English version of DIN EN 12848:2009-07

DIN EN 13075-2:2009 沥青和沥青粘接剂.断裂性能的测定.第2部分:阳离子沥青乳化液精确混合时间测定,DIN EN 13075-2:2009-07的英文版本

This European Standard specifies a method for the determination of the fines mixing time of diluted cationic bituminous emulsions, under standardized conditions.

Bitumen and bituminous binders - Determination of breaking behaviour - Part 2: Determination of fines mixing time of cationic bituminous emulsions; English version of DIN EN 13075-2:2009-07