F12 太阳能 标准查询与下载

NB/T 34048-2017 中温真空太阳吸收涂层

Medium temperature vacuum solar absorbing coating

NB/T 34043-2017 太阳能热水工程不锈钢常压储热水箱

Solar hot water engineering stainless steel normal pressure hot water storage tank

NB/T 34046-2017 家用太阳能热水系统安全技术规范

Safety technical specifications for household solar water heating systems

NB/T 34049-2017 太阳能热水工程施工、监理及验收规范

Specifications for construction, supervision and acceptance of solar water heating projects

NB/T 34044-2017 季节蓄热太阳能热利用工程技术规范

Technical Specifications for Seasonal Storage Solar Thermal Utilization Engineering

IEC 62817:2014/AMD1:2017 光伏系统. 太阳跟踪器的设计资质.修改件1

Photovoltaic systems - Design qualification of solar trackers

BS PD IEC/TS 62916:2017 光伏模组. 旁路二极管静电放电敏感试验

Photovoltaic modules. Bypass diode electrostatic discharge susceptibility testing

BS EN 62670-3:2017 聚光光伏(CPV). 性能试验. 性能测量和功率定额

Photovoltaic concentrators (CPV). Performance testing. Performance measurements and power rating

DIN IEC/TS 62941:2017 地面光伏(PV)模组. 光伏模块设计评定和型式批准信心增加指南(IEC/TS 62941-2016)

Terrestrial photovoltaic (PV) modules - Guidelines for increased confidence in PV module design qualification and type approval (IEC/TS 62941:2016)

IEC TS 62446-3:2017 光伏(PV)系统. 试验, 文档和维护要求. 第3部分: 光伏模组和电站. 室外红外热成像法

This part of IEC 62446 defines outdoor thermographic (infrared) inspection of PV modules and plants in operation. The inspection can include cables, contacts, fuses, switches, inverters, and batteries. This inspection supports the preventive maintenance for fire protection, the availability of the system for power production, and the inspection of the quality of the PV modules. Included in this document are the requirements for the measurement equipment, ambient conditions, inspection procedure, inspection report, personnel qualification and a matrix for thermal abnormalities as a guideline for the inspection. This document defines outdoor thermography on photovoltaic (PV) modules and Balance-of- system (BOS) components of PV power plants in operation, using passive techniques (standard system operating conditions under natural sunlight, without any external power or irradiation sources). IEC 60904-12-1 covers general methods for laboratory or production-line PV module thermographic imaging but not the specific details that are most relevant to outdoor imaging of operational power plants including BOS components. Two different levels of inspections are currently used: a) A simplified thermographic inspection. This is a limited inspection to verify that the PV modules and BOS components are functioning, with reduced requirements for the qualification of personnel. For example, during a basic commissioning of a PV plant. Authoritative conclusions regarding module quality are not possible with this inspection, and examples of abnormalities are provided to aid the inspector. b) A detailed thermographic inspection and analysis. This may include thermal signatures which differ from the examples provided, and therefore requires a deeper understanding of the thermal abnormalities. For example, it may be used for periodic inspections according to the IEC 62446 series and for trouble-shooting the cause of underperforming systems. Absolute temperature measurements may be made. An authorized expert in PV plants, together with thermography experts can perform the inspection.

Photovoltaic (PV) systems - Requirements for testing, documentation and maintenance - Part 3: Photovoltaic modules and plants - Outdoor infrared thermography

DIN IEC/TS 62782:2017 光伏(PV)模组. 循环(动态)机械载荷试验(IEC/TS 62782-2016)

Photovoltaic (PV) modules - Cyclic (dynamic) mechanical load testing (IEC/TS 62782:2016)

JIS C 8919 ERRATUM 1:2017 勘误

ERRATUM 1

IEC 60904-1-1:2017 光伏器件 第 1-1 部分：多结光伏（PV）器件的电流-电压特性测量

This part of IEC 60904 describes procedures for the measurement of the current-voltage characteristics of multi-junction photovoltaic devices in natural or simulated sunlight. It is applicable to single PV cells, sub-assemblies of such cells or entire PV modules. It is principally intended for non-concentrating devices, but parts may be applicable also to concentrating multi-junction PV devices. An essential prerequisite is the spectral responsivity of the multi-junction devices, whose measurement is covered by IEC 60904-8-1. The requirements for measurement of current-voltage characteristics of single-junction PV devices are covered by IEC 60904-1 whereas this document describes the additional requirements for the measurement of current-voltage characteristics of multi-junction PV devices. This document may be applicable to PV devices designed for use under concentrated irradiation if they are measured without the optics for concentration and irradiated using direct normal irradiance and a mismatch correction with respect to a direct normal reference spectral irradiance distribution is performed. The reference spectral irradiance distribution is provided in IEC 60904-3

Photovoltaic devices - Part 1-1: Measurement of current-voltage characteristics of multi-junction photovoltaic (PV) devices

DIN EN 61853-2:2017 光伏(PV)模块性能试验和能源评级. 第2部分: 光谱响应率, 入射角和模块操作温度测量(IEC 61853-2-2016); 德文版本 EN 61853-2-2016

Photovoltaic (PV) module performance testing and energy rating - Part 2: Spectral responsivity, incidence angle and module operating temperature measurements (IEC 61853-2:2016); German version EN 61853-2:2016

DIN EN 61215-1:2017 地面光伏(PV)模组. 设计质量和型式批准. 第1部分: 试验要求(IEC 61215-1-2016); 德文版本EN 61215-1-2016

Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 1: Test requirements (IEC 61215-1:2016); German version EN 61215-1:2016

IEC 60904-8-1:2017 光伏设备. 第8-1部分: 多接点光伏(PV)设备光谱响应率的测量

This part of IEC 60904 gives guidance for the measurement of the spectral responsivity (SR) of multi-junction photovoltaic devices. It is principally intended for non-concentrating devices, but parts may be applicable also to concentrating multi-junction PV devices. The SR is required for analysis of measured current-voltage characteristics of multi-junction PV devices as described in IEC 60904-1-1. The requirements for measurement of SR of single-junction PV devices are covered by IEC 60904-8, whereas this document describes the additional requirements for the measurement of SR of multi-junction PV devices. This document only considers the measurement of SR of individual junction layers within a two-terminal multi-junction device. This document may be applicable to PV devices designed for use under concentrated irradiation if they are measured without the optics for concentration.

Photovoltaic devices - Part 8-1: Measurement of spectral responsivity of multi-junction photovoltaic (PV) devices

DIN EN 60904-3:2017 光电器件.第3部分:带基准光谱辐照数据的地球光电(PV)太阳能器件的测量原理(IEC 60904-3-2016);德文版本EN 60904-3-2016

Photovoltaic devices - Part 3: Measurement principles for terrestrial photovoltaic (PV) solar devices with reference spectral irradiance data (IEC 60904-3:2016); German version EN 60904-3:2016, with CD-ROM

DIN EN 12976-2:2017 太阳供热系统和部件.工厂制造系统.第2部分:试验方法;德文版本EN 12976-2-2017

Thermal solar systems and components - Factory made systems - Part 2: Test methods; German version EN 12976-2:2017

IEC TS 62916:2017 光伏模组. 旁路二极管静电放电敏感试验

This document describes a discrete component bypass diode electrostatic discharge (ESD) immunity test and data analysis method. The test method described subjects a bypass diode to a progressive ESD stress test and the analysis method provides a means for analyzing and extrapolating the resulting failures using the two-parameter Weibull distribution function. It is the object of this document to establish a common and reproducible test method for determining diode surge voltage tolerance consistent with an ESD event during the manufacturing, packaging, transportation or installation processes of PV modules. This document does not purport to address causes of electrostatic discharge or to establish pass or fail levels for bypass diode devices. It is the responsibility of the user to assess the ESD exposure level for their particular circumstances. The data generated by this procedure may support qualification of new design types, quality control for incoming material, and/or identify the need for additional ESD controls in the manufacturing process. Finally, this document does not apply to large energy surge events such as direct or indirect lightning exposure, utility capacitor bank switching events, or the like.

Photovoltaic modules - Bypass diode electrostatic discharge susceptibility testing

DIN EN 12976-1:2017 太阳供热系统和部件.工厂制造系统.第1部分:一般要求;德文版本EN 12976-1-2017

Thermal solar systems and components - Factory made systems - Part 1: General requirements; German version EN 12976-1:2017