F12 太阳能 标准查询与下载

UL 1741 CRD-2013 用于分布式能源的逆变器, 转换器, 控制器和互连系统设备的UL安全标准. 节/段落参考: 第101节至第107节主题: 光伏输入电路合成器和光伏汇流箱的说明. 该认证要求决策 (CRD) 取代之前与2011年6月10日签发的CRD (第二版: 2010年1月28日)

UL Standard for Safety Inverters, Converters, Controllers and Interconnection System Equipment for Use With Distributed Energy Resources - Section / Paragraph Reference: Sec. 101 to 107 Subject: Clarification for PV Input Circuit Combiners and PV Combiner

IEC TS 62257-9-5:2013 农村电气化用小型可再生能源和混合系统的建议.第9-5部分:综合系统.农村电气化工程用便携PV提灯的选择

This part of IEC 62257 applies to stand-alone rechargeable electric lighting appliances or kits that can be installed by a typical user without employing a technician. This technical specification presents a quality assurance framework that includes product specifications (a framework for interpreting test results), test methods, and standardized specifications sheets (templates for communicating test results).

Recommendations for small renewable energy and hybrid systems for rural electrification - Part 9-5: Integrated system - Selection of stand-alone lighting kits for rural electrification

BS ISO 9459-4:2013 太阳能加热.家用热水系统.利用组合测验和计算机模拟的系统性能特征

Solar heating. Domestic water heating systems. System performance characterization by means of component tests and computer simulation

ISO 9459-4:2013 太阳能加热.家用热水系统.第4部分:借助于组合测验和计算机模拟的系统性能特征

Solar heating - Domestic water heating systems - Part 4: System performance characterization by means of component tests and computer simulation

NF P50-532-5:2013 热太阳能系统和组件.定制系统.第5部分:控制设备用性能试验方法

Thermal solar systems and components - Custom built systems - Part 5: performance test methods for control equipment

NF P50-532-2:2013 热力太阳能系统和部件. 定制系统. 第2部分: 太阳能热水器和联合系统的试验方法

Thermal solar systems and components - Custom built systems - Part 2: test methods for solar water heaters and combisystems

NF P50-532-1:2013 热力太阳能系统和部件. 定制系统. 第1部分: 太阳能热水器和联合系统的通用要求

Thermal solar systems and components - Custom built systems - Part 1: general requirements for solar water heaters and combisystems

NF P50-532-3:2013 太阳热能系统和部件.定制系统.第3部分:太阳能热水器储存用性能试验方法

Thermal solar systems and components - Custom built systems - Part 3: performance test methods for solar water heater stores

NF P50-532-4:2013 热太阳能系统和组件.定制系统.第4部分:太阳能燃烧室性能测试方法

Thermal solar systems and components - Custom built systems - Part 4: performance test methods for solar combistores

ANSI S1001.1-2013 太阳能热水系统的设计和安装

Design and Installation of Solar Water Heating Systems

EN ISO 9806:2013 太阳能.太阳能集热器.试验方法

Diese Internationale Norm legt Prufverfahren fur die Bewertung der Dauerhaftigkeit, Zuverlassigkeit und Sicherheit von Fluidkollektoren fest. Auserdem enthalt diese Internationale Norm Prufverfahren fur die Beschreibung von Fluidkollektoren hinsichtlich ihrer Warmeleistung, d. h. der Warmeleistung von abgedeckten und unabgedeckten Fluidkollektoren im stationaren Zustand und unter quasi-dynamischen Bedingungen und der Warmeleistung von abgedeckten und unabgedeckten Luftkollektoren (mit offenem und geschlossenem Kreislauf). Diese Internationale Norm gilt auch fur Hybridkollektoren, die Warme und Strom erzeugen. Sie deckt jedoch keine die elektrische Sicherheit betreffenden Eigenschaften oder sonstige besondere Eigenschaften ab, die sich auf die Stromerzeugung beziehen. Diese Internationale Norm gilt auch fur Kollektoren, die externe Stromquellen fur den Normalbetrieb und/oder sicherheitsrelevante Zwecke nutzen. Diese Internationale Norm ist nicht auf Kollektoren anwendbar, bei denen der Warmespeicher ein integraler Bestandteil des Kollektors ist, sodass sich der Prozess im Kollektor nicht vom Prozess der Warmespeicherung trennen lasst, wie dies erforderlich sein kann, um beispielsweise Messungen in Bezug auf diese beiden Prozesse durchzufuhren.

Solar energy - Solar thermal collectors - Test methods [Superseded: CEN EN 12975-2]

ASTM E861-13 太阳能收集器用绝热材料评定的标准实施规程

5.1 The exposure conditions in solar collectors, especially under stagnation conditions, may degrade the performance of thermal insulation materials. This practice sets forth a methodology for evaluating the degree of degradation, if any, of the thermal insulation materials after exposure to simulated in-service conditions. 5.2 This practice is also intended to aid in the assessment of long-term performance by comparative testing of insulation materials. However, correlations between performance under laboratory and actual in-service conditions have not been established. 5.3 This practice also sets forth criteria that shall be considered in the selection and specification of thermal insulation materials. One such criterion is surface burning characteristics (Test Method E84), which is used by many code officials as a reference. This practice does not represent that the numerical values obtained in any way reflect the anticipated performance of the thermal insulation under actual fire conditions. 1.1 This practice sets forth a testing methodology for evaluating the properties of thermal insulation materials to be used in solar collectors with concentration ratios of less than 10. Tests are given herein to evaluate the pH, surface burning characteristics, moisture adsorption, water absorption, thermal resistance, linear shrinkage (or expansion), hot surface performance, and accelerated aging. This practice provides a test for surface burning characteristics but does not provide a methodology for determining combustibility performance of thermal insulation materials. 1.2 The tests shall apply to blanket, rigid board, loose-fill, and foam thermal insulation materials used in solar collectors. Other thermal insulation materials shall be tested in accordance with the provisions set forth herein and should not be excluded from consideration. 1.3 The assumption is made that elevated temperature, moisture, and applied stresses are the primary factors contributing to the degradation of thermal insulation materials used in solar collectors. 1.4 Solar radiation is not considered a contributing factor since insulating materials are not normally exposed to it. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Evaluating Thermal Insulation Materials for Use in Solar Collectors

ASTM E1160-13 太阳能家用热水系统的现场检查和操作验证的标准指南

4.1 This guide is intended for on-site assessment of in-service operation by short term measurement of appropriate system functions under representative operating conditions. 4.2 Primary application is for residential systems and medium-size multi-family units or commercial buildings. Use of back-up conventional DHW heating system is assumed to augment solar heating. 4.3 This guide is intended for use by suppliers, installers, consultants and homeowners in evaluating on-site operation of an installed system. Emphasis is placed on simplified measurements that do not require special skills, intrusive instrumentation, system modification or interruption of service to the purchaser. 4.4 The purpose of this guide is to verify that the system is functioning. Copies of all data and reports must be submitted by the testing group to the owner or his or her designated agent. 4.5 Data and reports from these procedures and tests may be used to compare the system performance over time, but should not be used to compare different systems or installations. 4.6 Test is for a newly installed system and also for periodic checking. 1.1 This guide covers procedures and test methods for conducting an on-site inspection and acceptance test of an installed domestic hot water system (DHW) using flat plate, concentrating-type collectors or tank absorber systems. 1.2 It is intended as a simple and economical acceptance test to be performed by the system installer or an independent tester to verify that critical components of the system are functioning and to acquire baseline data reflecting overall short term system heat output. 1.3 This guide is not intended to generate accurate measurements of system performance (see ASHRAE standard 95-1981 for a laboratory test) or thermal efficiency. 1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for On-Site Inspection and Verification of Operation of Solar Domestic Hot Water Systems

ASTM E772-13 太阳能转换相关标准术语

1.1 This terminology pertains to the conversion of solar energy into other forms of energy by various means, including thermal absorption (i.e., solar thermal) and the photovoltaic effect (i.e., photovoltaics). 1.2 This terminology also pertains to instrumentation used to measure solar radiation. 1.3 This terminology also pertains to glass for solar energy applications. 1.4 Fundamental terms associated with electromagnetic radiation that are indicates as derived units in Standard IEEE/ASTM SI 10 are not repeated in this terminology. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

Standard Terminology of Solar Energy Conversion

QB/T 4405-2012 家用电辅助加热太阳能热水系统

本标准规定了家用电辅助加热太阳能热水系统(以下简称“热水系统”)的术语和定义、要求、试验方法、制造和生产试验、检验规则、标志、包装、运输、贮存。本标准适用于带储水箱且储水箱容积在600 L以下的家用电辅助加热太阳能热水系统。

Household electric auxiliary solar water heating system

JGJ/T 264-2012 光伏建筑一体化系统运行与维护规范

本规范适用于验收合格并投入正常使用的光伏建筑一体化系统运行与维护。

Code for operation and maintenance of building mounted photovoltaic system

KS C IEC 60904-10:2012 光伏器件.第10部分:线性测量方法

이 표준은 시험 매개변수에 대해 태양광발전 소자 매개변수의 선형도를 결정하는 데 사용되는

Photovoltaic devices-Part 10:Methods of linearity measurement

KS C IEC 60904-4:2012 光伏器件.第4部分:标准太阳能装置.校正可追溯性的确立过程

이 표준은 태양광발전 기준 태양광 소자가 KS C IEC 60904-2에서 요구하는 SI

Photovoltaic devices－Part 4：Reference solar devices－Procedures for establishing calibration traceability

KS C IEC 60891:2012 光伏器件.测定I.V特性的温度和辐照度校正方法用程序

이 표준은 결정계 실리콘 태양광발전 소자의 측정된 I-V 특성에 의한 온도 및 조사강도 보

Photovoltaic devices－Procedures for temperature and irradiance corrections to measured I-V characteristics

DB34/ 1801-2012 太阳能热水系统与建筑一体化技术规程

本规程适用于我省使用太阳能热水系统的新建、扩建和改建的民用建筑和工业建筑，以及增设和改造太阳能热水系统的既有建筑。

Technical specification for solar water heating system and building integration