G30 合成材料综合 标准查询与下载

HG/T 2582-1994 橡胶或塑料涂覆织物耐透水性测定

本标准规定了橡胶或塑料涂覆织物承受低或高静水压时耐透水性能的测定方法。 本标准适用于测定橡胶或塑料涂覆织物及其制品的耐透水性。 本标准包括四种方法： 方法A1和A2：低青水压--大试样方法。 方法B1和B2：高静水压--小试样方法。

Determination of resistance to water penetration of rubber or plastic coated fabrics

HG/T 2581-1994 橡胶或塑料涂覆织物耐撕裂性能的测定

本标准规定了橡胶或塑料涂覆织物耐撕裂性能的测定方法。 本标准包括梯形法撕裂强力、双舌单撕法撕裂强力及三舌双撕法撕裂强力三种方法。 同一橡胶或塑料涂覆织物得到的梯形法、单撕法及双撕法撕裂强力的试验结果不能相互比较；双撕法撕裂强力试验，两种不同舌宽的试验结果也不能相互比较。 本标准适用于被撕断底布垂直于撕裂方向的涂覆织物，不适用于撕裂形式复杂的以网格布或针织物为底布的涂覆织物。

Determination of tear resistance of rubber or plastic coated fabrics

HG/T 2583-1994 橡胶涂覆织物绝缘带物理性能的测定

本标准规定了电工用橡胶涂覆织物绝缘带的物理性能测定方法，本方法包括10、15、20 mm宽的低压绝缘带的厚度、宽度、粘着性、对金属的腐蚀性、透光点个数、工频击穿强度及耐电压的测定。 本标准适用于由纤维织物经涂覆绝缘胶料而制成的，可以在-10～+40℃的温度环境中，电压不大于380V情况下使用的通用电线和电缆包扎防护绝缘用的绝缘带的物理性能的测定。

Determination of physical properties of rubber-coated fabric insulating tape

HG/T 2580-1994 橡胶或塑料涂覆织物拉伸强度和扯断伸长率的测定

本标准规定了橡胶或塑料涂覆织物拉伸强度和扯断伸长率的测定方法。 本标准适用于橡胶或塑料涂覆织物条状的干试样或湿试样拉伸强度和扯断伸长率的测定。 本标准不适用于网眼布和针织布为底布的涂覆织物。

Determination of tensile strength and elongation at break of rubber or plastics coated fabrics

BS 7709-5:1993 玻璃提取液的分析 分子吸收光谱法和火焰原子吸收光谱法测定氧化铁（III）的方法

This part of ISO 10136 specifies an analytical pro-cedure, using molecular absorption spectrometry and flame atomic absorption spectrometry, for measuring the concentrations of iron, expressed as iron(lll) oxide (Fe2O3), released into extract solutions during hydrolytic resistance test procedures. This part of ISO 10136 applies to the analysis of ex-tract solutions obtained from any kind of glass or glassware, including laboratory and pharmaceutical ware made, for example, from borosilicate glass (such as borosilicate glass 3.3 according to ISO 3585), neu-tral glass, or soda-lime-silica glass as defined in ISO 4802[3][4], food and drink packaging ware, table-ware and kitchenware. The extract solution may be obtained from glass articles, for example according to ISO 4802 or from glass as material, for example when tested according to ISO 719[1] or ISO 720[2]. In ad-dition, it may be applied to the extract solutions pro-duced by any method for measuring the hydrolytic resistance of glass or glassware.

Analysis of extract solutions of glass. Method for determination of iron (III) oxide by molecular absorption spectrometry and flame atomic absorption spectrometry

DIN ISO 4638:1993 柔性泡沫聚合材料.透气率的测定

The document specifies a method for the determination of the permeability of flexible cellular polymeric materials to air flow, it is applicable to test pieces cut from products of cellular material.#,,#

Polymeric materials, cellular flexible; determination of air flow permeability; identical with ISO 4638:1984

BS 3502-3:1993 塑料和橡胶材料符号.第3部分:配料成分符号一览表

Provides unambiguous symbols comprising accelerators and vulcanizing agents, activators and process aids, antioxidants and antiozonants, blowing agents, plasticizers, retarders of vulcanization, and fillers and reinforcing materials for plastics.

Symbols for plastics and rubber materials - Schedule for symbols for compounding ingredients

DIN 65474:1992 航空航天.纤维增强的塑料.温度锋值试验方法

Aerospace; fibre reinforced plastics; thermal-spike test method

BS 4443-7:1992+A1:2008 柔性泡沫材料用试验方法.方法17.用整个表层测定柔性泡沫材料的撕裂强度

This Part of BS 4443 describes !the" method of test that applies to flexible cellular products of polymeric origin: determination of tear strength of flexible materials with an integral skin and a density not greater than 500 kg/m3 and determination of compression set under humid conditions. NOTE 1 The tear strength method described produces a value that may be regarded as a measure of the tear strength of the skinned foam under the conditions of the particular test. NOTE 2 The titles of the publications referred to in this standard are listed on the inside back cover.

Methods of test for Flexible cellular materials — Part 7: Method 17. Determination of tear strength of flexible cellular material with an integral skin

ISO 3384:1991/Cor 1:1992 硫化橡胶或热塑橡胶.在常温和高温压缩时应力松弛的测定.技术勘误表1

Rubber, vulcanized or thermoplastic; determination of stress relaxation in compression at ambient and at elevated temperatures; technical corrigendum 1

ISO 10120:1991 碳纤维.线性密度的测定

This International Standard specifies a method for determining the linear density (mass per unit length) of carbon fibre yarns. When the determination of the linear density is car- ried out on sized fibre, a correction shall be made by calculation based:on the size content (see 10.2). The linear density determined by the method speci- fied in this International Standard does not consider the influence of twist in the yarn.

Carbon fibre; determination of linear density

ISO 10066:1991 软质泡沫聚合材料 压缩蠕变性能测定

Contains a procedure intended primarily for quality assurance in packaging applications. Describes the principle, the apparatus, the preparation of specimens, conditioning methods, the test procedure, and the contents of the test report.

Flexible cellular polymeric materials; determination of creep in compression

BS 4370-4:1991 硬质微孔材料试验方法.第4部分:方法14:弯曲性能测定

Standardized method for measuring.

Methods of test for rigid cellular materials - Method 14 - Determination of flexural properties

NAVY MIL-I-8574 E VALID NOTICE 1-1991 易挥腐蚀发抑制剂的综合利用

MIL-I-8574E (l), dated 6 April 1984, has been reviewed and determined to be valid f-or us8 in acquisition.

INHIBITORS, CORROSION, VOLATILE, UTILIZATION OF

DIN 53545:1990 橡胶的试验.橡胶耐低温性能的测定.原理和试验

The standard deals with the determination of the behaviour at low temperatures of rubber.

Determination of low-temperature behaviour of elastomers; principles and test methods

DIN 53531-2:1990 用锥端圆柱体测定橡胶与刚性材料的粘合力

Determination of the adhesion of rubber to rigid materials using conical ended cylinders

ISO 4675:1990 橡胶或塑料涂覆织物 低温弯曲试验

Describes a method for the materials given determining the ability to resist the low-temperature effect to bending at special temperatures after definite periods of exposure. Applicable to material which a thickness between 0.10 and 2.20 mm. Since these materials are used in different applications, no general relationship between this test and the service performance can be given or implied. Two figures show the test apparatus.

Rubber- or plastics-coated fabrics; low-temperature bend test

ISO 3303:1990 橡胶或塑料涂覆织物 撕裂强度的测定

Lays down two methods: one using a testing tensile machine with a ring clamp and steel ball and the other using a diaphragm bursting tester operated by hydraulic pressure. The apparatus for the two methods are shown in figures.

Rubber- or plastics-coated fabrics; determination of bursting strength

ISO 5978:1990 橡胶或塑料涂覆织物 耐粘结强度测定

The method specified is acceptable in most cases. If it is desired to use conditions other than those specified, these may be mutually agreed between the contracting parties, but such variations shall be stated in the test report. - Constitutes a minor revision of the first edition.

Rubber- or plastics-coated fabrics; determination of blocking resistance

ISO 4646:1989 橡胶或塑料涂覆织物 低温冲击试验

本标准规定了测定橡胶或塑料涂覆织物在承受规定的冲击条件时未出现断裂或涂覆层龟裂的最低 温度的方法。 橡胶或塑料涂覆织物应用于许多有冲击或无冲击的低温弯曲的制品中。本方法获得的数据可以用 于预测这些涂覆织物仅在本方法所示变形条件制品中的低温性能。

Rubber- or plastics-coated fabrics; low-temperature impact test