G38 胶粘剂基础标准与通用方法 标准查询与下载

NF T76-340-2:2009 粘合剂.室内木材制品用粘合剂的选择与评定用试验方法.第2部分:恶劣环境下的抗剥离性

Adhesives - Test methods for the evaluation and selection of adhesives for indoor wood products - Part 2 : resistance to delamination in severe environments.

NF T76-340-1:2009 粘合剂.室内木材制品用粘合剂的选择与评定用试验方法.第1部分:非恶劣环境下的抗剥离性

Adhesives - Test methods for the evaluation and selection of adhesives for indoor wood products - Part 1 : resistance to delamination in non-severe environments.

KS M ISO 15108:2009 胶黏剂.用弯曲剪切法测定胶粘连接处的强度

이 표준은 굽힘 전단법을 이용하여 접합 부분의 강도를 측정하는 절차에 대해 규정한다. 이

Adhesives－Determination of strength of bonded joints using a bending-shear method

SANS 10183-3-2:2009 木材胶粘剂．第3-2部分：非结构应用．测定搭接接头的抗拉伸剪切强度

Describes tests for adhesives for wood and derived timber products for the assessment of their resistance to hot and cold water. Can be used for the assessment of the strength of bonds with a thin or thick bond-line. Does not apply to adhesives for stru

Adhesives for wood Part 3-2: Non-structural applications - Determination of tensile shear strength of lap joints

SANS 10183-4-5:2009 木材胶粘剂．第4-5部分：测试方法．压力剪切多重粘结样品的静载荷试验

Specifies a method of determining the ability of adhesive bonds to resist static load. Is applicable to adhesives used in load bearing timber structures. Is suitable for assessing the compliance of adhesives according to prEN 15425 and assessing the sui

Adhesives for wood Part 4-5: Test methods - Static load test of multiple bondline specimens in compression shear

SANS 10183-3-1:2009 木材胶粘剂．第3-1部分：非结构应用．非结构热塑性木材胶粘剂分类

Classifies thermoplastic resin based wood adhesives for non-structural applications classified into durability classes D1 to D4 based on the dry and wet strengths of bond-lines measured under specified conditions after various conditioning treatments.

Adhesives for wood Part 3-1: Non-structural applications - Classification of thermoplastic wood adhesives for non-structural applications

SANS 10183-4-3:2009 木材胶粘剂．第4-3部分：测试方法．通过温度和湿度循环试验测定木纤维酸性腐蚀对横向拉伸强度的影响

Specifies a method for determining the effect on bond strength of damage to wood fibres caused by the action of acids from the adhesive during climatic cycling. Is suitable for assessing the compliance of adhesives with EN 301, assessing the suitability

Adhesives for wood Part 4-3: Test methods - Determination of the effect of acid damage to wood fibres by temperature and humidity cycling on the transverse tensile strength

SANS 10183-3-3:2009 木材胶粘剂．第3-3部分：非结构应用．非结构用热固性木基胶粘剂的分类

Classifies thermosetting resin based wood adhesives for non-structural applications into durability classes C1 to C4 based on the dry and wet strengths of bond-lines measured under specified conditions after various conditioning treatments. Describes adh

Adhesives for wood Part 3-3: Non-structural applications - Classification of thermosetting wood adhesives for non-structural applications

SANS 10183-4-2:2009 木材胶粘剂．第4-2部分：测试方法．测定抗脱层

Specifies a method for determining the resistance to delamination of bonded joints. Suitable for assessing the compliance of adhesives with EN 301, assessing the suitability and quality of adhesives for load-bearing timber structures, and comparing the e

Adhesives for wood Part 4-2: Test methods - Determination of resistance to delamination

SANS 10183-4-1:2009 木材胶粘剂．第4-1部分：测试方法．测定纵向拉伸剪切强度中的粘接强度

Specifies a method of determining the shear strength of adhesive bonds. Is applicable to adhesives used in load-bearing timber structures. Not intended for use to provide numerical design data, nor is it applicable to the assessment of adhesives for th

Adhesives for wood Part 4-1: Test methods - Determination of bond strength in longitudinal tensile shear strength

SANS 10183-4-4:2009 木材胶粘剂．第4-4部分：测试方法．测定木材收缩对剪切强度的影响

Specifies a method for determining the extent to which wood shrinkage under drying conditions will weaken an adhesive bond. Is suitable for assessing the compliance of adhesives with EN 301, assessing the suitability and quality of adhesives for load-bea

Adhesives for wood Part 4-4: Test methods - Determination of the effects of wood shrinkage on the shear strength

BS ISO 25217:2009 粘合剂.用双悬臂梁和锥形双悬臂梁试样测定结构胶粘剂的I型粘合断裂力

Adhesives - Determination of the mode 1 adhesive fracture energy of structural adhesive joints using double cantilever beam and tapered double cantilever beam specimens

DIN EN 14188-4:2009 接缝填充剂和密封剂.第4部分:与对接密封剂配合使用的底漆规范,英文版本DIN EN 14188-4-2009-10

This European Standard specifies requirements for material characterisation for primers for hot and cold applied joint sealants for use in roads, airfields and other concrete pavements. This European Standard also applies to primers for hot and cold applied joint sealants in bituminous surfacing and a bituminous surfacing and an adjacent concrete pavement.

Joint fillers and sealants - Part 4: Specifications for primers to be used with joint sealants; English version of DIN EN 14188-4:2009-10

ISO 26842-2:2009 粘合剂.室内木制品用粘合剂评估和选择的测试方法.第2部分:恶劣环境中测定的阻力

Adhesives - Test methods for the evaluation and selection of adhesives for indoor wood products - Part 2: Resistance to delamination in severe environments

NF T76-123*NF EN 15870:2009 胶粘剂.对接接头拉伸强度的测定

Adhesives - Determination of tensile strength of butt joints.

DIN EN 15865:2009 粘合剂.螺纹紧固件上厌氧粘合剂的抗扭强度的测定(ISO 10964:1993修改件),DIN EN 15865:2009-08的英文版本

The test method described in this European Standard is used to make comparative assessments of the securing or locking effect of anaerobic adhesives used in threaded assemblies. This method may be used for other types of adhesives, if considered suitable.

Adhesives - Determination of torque strength of anaerobic adhesives on threaded fasteners (ISO 10964:1993 modified); English version of DIN EN 15865:2009-08

DIN EN 13999-3:2009 胶粘剂.低溶剂和无溶剂的胶粘剂使用后的释放特性的短期测量方法.第3部分:挥发性二异氰酸盐的测定(包括修改件A1-2009).英文版本DIN EN 13999-3-2009-08

This European Standard specifies a procedure for the determination of volatile aldehydes (especially formaldehyde and acetaldehyde) and other carbonyl compounds in the exhaust air of an emission test chamber after application of a low-solvent or solvent-free adhesive as defined in EN 923. The method is based on chemosorption of volatile carbonyl compounds with 2,4-dinitrophenylhydrazine (in the following: DNPH) impregnated silica tubes or cartridges with subsequent solvent desorption, clean-up and liquid chromatographic analysis. The method permits measurement of several aldehydes including formaldehyde, acetaldehyde, propionaldehyde, butyraldehyde, valeraldehyde, isovaleraldehyde, hexanal, benzaldehyde, 2,5-dimethylbenzaldehyde, o-tolualdehyde, m-tolualdehyde, p-tolualdehyde, crotonaldehyde in the concentration range of approximately 10 μg/m3 to 1 mg/m3 (see ISO 16000-3).

Adhesives - Short term method for measuring the emission properties of low-solvent or solvent-free adhesives after application - Part 3: Determination of volatile aldehydes(includes Amendment A1:2009); English version of DIN EN 13999-3:2009-08

DIN EN 15870:2009 胶粘剂.对接接头拉伸强度的测定(ISO 6922:1987修改件),DIN EN 15870:2009-08的英文版

This European Standard specifies a method for determining the bond strength of a butt joint when subjected to tensile force. The method can be applied to all types of adhesives. Although primarily intended for use under ambient conditions, the basic method can also be applied to testing under a wide range of temperature and other environmental conditions. The method requires rigid adherends that can be produced to the required dimensional tolerances and that will withstand the forces applied to them during the test.

Adhesives - Determination of tensile strength of butt joints (ISO 6922:1987 modified); English version of DIN EN 15870:2009-08

DIN EN 13999-4:2009 粘合剂.低溶剂或无溶剂胶粘剂使用后的排放性能的短期测量方法.第4部分:挥发性二异氰酸酯的测定(包括修改件A1-2009).英文版本DIN 13999-4-2009-08

This European Standard specifies a procedure for the determination of volatile isocyanates in the exhaust air of an emission test chamber after application of a low-solvent or solvent-free adhesive as defined in EN 923. The method is based on chemosorption of volatile isocyanates with 1-(2-methoxyphenyl) piperazine (in the following: 1-2MP) impregnated filters with subsequent desorption and liquid chromatographic analysis. The method permits measurement of a wide range of organic compounds containing isocyanate functional groups (NCO), including isocyanate monomers. For testing of adhesives emissions mainly toluene diisocyanate (TDI) and methylene bis (4-phenyl isocyanate also known as 4,4-diisocyanato-diphenylmethane or MDI), are of concern. The method as described in this European Standard can be used for other isocyanates too, such as isophorone diisocyanate (IPDI) and 1,6-hexamethylene diisocyanate (HDI) - see ISO 16702. Isocyanate oligomers or prepolymers are not volatile enough to be detected in emission test chambers at room tem perature.

Adhesives - Short term method for measuring the emission properties of low-solvent or solvent-free adhesives after application - Part 4: Determination of volatile diisocyanates(includes Amendment A1:2009); English version of DIN EN 13999-4:2009-08

NF T76-140-3*NF EN 13999-3+A1:2009 粘合剂.低溶剂或无溶剂胶粘剂使用后排放特性的测量用短期方法.第3部分:挥发性醛类的测定

Adhesives - Short term method for measuring the emission properties of low-solvent or solvent-free adhesives after application - Part 3 : determination of volatile aldehydes.