G38 胶粘剂基础标准与通用方法 标准查询与下载

DIN EN 1465:2009 粘合剂.粘合组件的拉伸搭接剪切强度的测定,英文版DIN EN 1465:2009-07

This European Standard specifies a method for determining the tensile lap-shear strength of bonded assemblies when tested on a standard specimen and under specified conditions of preparation and testing. NOTE 1 This test procedure is not applicable for calculations needed for bond design in structural joints. NOTE 2 This test Test methods for the determination of tensile lap-shear strength of bonded assemblies with wood adhesives are also specified in EN 205 and EN 302-1

Adhesives - Determination of tensile lap-shear strength of bonded assemblies; English version of DIN EN 1465:2009-07

DIN EN 1966:2009 结构粘合剂.三点弯曲法测量粘合剂表面的特性,DIN EN 1966:2009-07的英文版本

This European Standard describes a test method to determine ability of a cured adhesive (possibly with a primer) to adhere to a substrate which has had a certain surface finish or with a specific surface preparation by using the "three point bending method". It is only used for quality assurance and the substrate should be rigid or resistant enough to bending such as steel or aluminium alloys. For other substrates the thickness should be adjusted to the modulus of elasticity or a suitable stiffener should be used. The adhesive should be polymerisable (curable) without pressure in order to obtain the thickness needed to provide sufficient rigidity, otherwise, a bonded reinforcing piece of the same type and same thickness as the substrate can be substituted for the bloc of adhesive. It is not suitable for film adhesives.

Structural adhesives - Characterization of a surface by measuring adhesion by means of the three point bending method; English version of DIN EN 1966:2009-07

NF T76-140-4*NF EN 13999-4+A1:2009 粘合剂.测定低溶剂或无溶剂粘合剂在施用后的排放性质的短期方法.第4部分:挥发性二异氰酸酯的测定

Adhesives - Short term method for measuring the emission properties of low-solvent or solvent-free adhesives after application - Part 4 : determination of volatile diisocyanates.

NF T76-140-4/IN1*NF EN 13999-4/IN1:2009 粘合剂.使用后低溶解或不溶解粘合剂排放性能的测量用短期方法.第4部分:挥发性二异氰酸盐酯的测定

Adhesives - Short term method for measuring the emission properties of low-solvent or solvent-free adhesives after application - Part 4 : determination of volatile diisocyanates.

BS EN 15865:2009 粘合剂.螺纹紧固件上用厌氧粘合剂的扭矩强度的测定

The test method described in this European Standard is used to make comparative assessments of the securing or locking effect of anaerobic adhesives used in threaded assemblies. This method may be used for other types of adhesives, if considered suitable.

Adhesives - Determination of torque strength of anaerobic adhesives on threaded fasteners

BS EN 15870:2009 粘合剂.对接接头抗拉强度的测定

This European Standard specifies a method for determining the bond strength of a butt joint when subjected to tensile force. The method can be applied to all types of adhesives. Although primarily intended for use under ambient conditions, the basic method can also be applied to testing under a wide range of temperature and other environmental conditions. The method requires rigid adherends that can be produced to the required dimensional tolerances and that will withstand the forces applied to them during the test.

Adhesives - Determination of tensile strength of butt joints

ISO 25217:2009 粘结剂.双悬臂梁和锥形双悬臂梁试样测定结构胶粘剂的1式粘结断裂力

This International Standard specifies a method, based upon linear elastic fracture mechanics (LEFM), for the determination of the fracture resistance of structural adhesive joints under an applied mode I opening load, using double cantilever beam (DCB) and tapered double cantilever beam (TDCB) specimens.

Adhesives - Determination of the mode 1 adhesive fracture energy of structural adhesive joints using double cantilever beam and tapered double cantilever beam specimens

NF T76-107*NF EN 1465:2009 粘合剂.粘结的配件拉伸重叠部分-剪切强度的测定

Adhesives - Determination of tensile lap-shear strength of bonded assemblies.

NF T76-143*NF EN 1966:2009 结构胶粘剂.用三点弯曲法测量粘结力的表面特征说明

Structural adhesives - Characterisation of a surface by measuring adhesion by means of the three point bending method.

EN 13999-4:2007+A1:2009 胶粘剂.短期的方法测量应用程序后低溶剂或无溶剂胶粘剂排放特性.第4部分:挥发性二异氰酸盐的测量

This European Standard specifies a procedure for the determination of volatile isocyanates in the exhaust air of an emission test chamber after application of a low-solvent or solvent-free adhesive as defined in EN 923. The method is based on chemosorption of volatile isocyanates with 1-(2-methoxyphenyl) piperazine (in the following: 1-2MP) impregnated filters with subsequent desorption and liquid chromatographic analysis. The method permits measurement of a wide range of organic compounds containing isocyanate functional groups (NCO), including isocyanate monomers. For testing of adhesives emissions mainly toluene diisocyanate (TDI) and methylene bis (4-phenyl isocyanate also known as 4,4-diisocyanato-diphenylmethane or MDI), are of concern. The method as described in this European Standard can be used for other isocyanates too, such as isophorone diisocyanate (IPDI) and 1,6-hexamethylene diisocyanate (HDI) - see ISO 16702. Isocyanate oligomers or prepolymers are not volatile enough to be detected in emission test chambers at room temperature.

Adhesives - Short term method for measuring the emission properties of low-solvent or solvent-free adhesives after application - Part 4: Determination of volatile diisocyanates

EN 13999-3:2007+A1:2009 胶粘剂.短期的方法测量应用程序后低溶剂或无溶剂胶粘剂排放特性.第3部分:挥发性乙醛的测量

This European Standard specifies a procedure for the determination of volatile aldehydes (especially formaldehyde and acetaldehyde) and other carbonyl compounds in the exhaust air of an emission test chamber after application of a low-solvent or solvent-free adhesive as defined in EN 923. The method is based on chemosorption of volatile carbonyl compounds with 2,4-dinitrophenylhydrazine (in the following: DNPH) impregnated silica tubes or cartridges with subsequent solvent desorption, clean-up and liquid chromatographic analysis. The method permits measurement of several aldehydes including formaldehyde, acetaldehyde, propionaldehyde, butyraldehyde, valeraldehyde, isovaleraldehyde, hexanal, benzaldehyde, 2,5-dimethylbenzaldehyde, o-tolualdehyde, m-tolualdehyde, p-tolualdehyde, crotonaldehyde in the concentration range of approximately 10 µg/m3 to 1 mg/m3 (see ISO 16000-3).

Adhesives - Short term method for measuring the emission properties of low-solvent or solvent-free adhesives after application - Part 3: Determination of volatile aldehydes

BS EN 1966:2009 机构粘合剂.用三点弯曲法测量粘附性的方法进行表面特性的表征

This European Standard describes a test method to determine ability of a cured adhesive (possibly with a primer) to adhere to a substrate which has had a certain surface finish or with a specific surface preparation by using the "three point bending method". It is only used for quality assurance and the substrate should be rigid or resistant enough to bending such as steel or aluminium alloys. For other substrates the thickness should be adjusted to the modulus of elasticity or a suitable stiffener should be used. The adhesive should be polymerisable (curable) without pressure in order to obtain the thickness needed to provide sufficient rigidity, otherwise, a bonded reinforcing piece of the same type and same thickness as the substrate can be substituted for the bloc of adhesive. It is not suitable for film adhesives.

Structural adhesives - Characterization of a surface by measuring adhesion by means of the three point bending method

BS EN 1465:2009 粘合剂.粘结的配件拉伸重叠部分-剪切强度的测定

This European Standard specifies a method for determining the tensile lap-shear strength of bonded assemblies when tested on a standard specimen and under specified conditions of preparation and testing. NOTE 1 This test procedure is not applicable for calculations needed for bond design in structural joints. NOTE 2 This test Test methods for the determination of tensile lap-shear strength of bonded assemblies with wood adhesives are also specified in EN 205 and EN 302-1

Adhesives. Determination of tensile lap-shear strength of bonded assemblies

ASTM D6114/D6114M-09 沥青橡胶粘结剂的标准规范

1.1 This specification covers asphalt-rubber binder, consisting of a blend of paving grade asphalt cements, ground recycled tire (that is, vulcanized) rubber and other additives, as needed, for use as binder in pavement construction. The rubber shall be blended and interacted in the hot asphalt cement sufficiently to cause swelling of the rubber particles prior to use. Note 18212;It has been found that at least 15 % rubber by weight of the total blend is usually necessary to provide acceptable properties of asphalt-rubber. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 The following precautionary caveat pertains to the test method portions only, Sections 4 and 5 of this Specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 4.3.2.

Standard Specification for Asphalt-Rubber Binder

ASTM D7532-09 地毯粘合剂重新粘性测定的标准实施规程

Selection of or development of a carpet adhesive, for direct glue or adhered applications requires knowledge of the adhesive's ability to perform adequately when it is found necessary to correct an installation concern, such as bubbles or wrinkles, by re-rolling or application of dead weight to the affected area without the application or injection of additional adhesive. Adhesive bonding of some carpet backings to substrates and the adhesive bonding of carpet backings to a pad foundation, double stick or glue application, require that prior to bonding the adhesive is to be dried sufficiently to allow for no transfer of adhesive as a result of slight finger pressure.1.1 This practice will provide a protocol for determining the effect of extended drying (open time) periods on the shear and peel strength performance of a carpet adhesive when bonding a carpet backing or standard duck cloth material to a substrate. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Determination of Re-tack Ability of Carpet Adhesives

KS M 3822-2008 环氧树脂和固化剂黏度的测定

이 표준은 상온에서 액체 상태 또는 용제로 희석된 에폭시 수지 및 경화제의 점도 시험 방법

Testing methods for viscosity of epoxide resins and hardners

KS M ISO 6238:2008 黏合剂.木材与木材黏合剂.用压缩负荷测定剪切强度

이 표준은 압축이 적용되는 표준 시료와 준비, 상태, 시험의 특정한 조건하에서 목재 대 목

Adhesives-Wood-to-wood adhesive bonds-Determination of shear strength by compression loading

KS M 3821-2008 环氧树脂和固化剂比重试验方法

이 표준은 에폭시 수지 및 경화제의 비중 시험방법에 대하여 규정한다.

Testing methods for specific gravity of epoxide resins and hardeners

KS M 3823-2008 环氧树脂软化点的测定方法

이 표준은 상온에서 고형 에폭시 수지의 연화점 시험방법에 대하여 규정한다.

Testing methods for softening point of epoxide resins

KS M 3824-2008 热塑聚氨酯弹性物试验方法

이 표준은 폴리우레탄계 열가소성 탄성체의 시험방법에 대하여 규정한다.

Testing methods for thermoplastic polyurethane elastomers