G39 胶粘剂 标准查询与下载

JIS K 6503:2001 动物胶及明胶

この規格は，動物の骨，皮，じん帯又はけんから得たフラーゲンを加水分解して製造した，にかわ及びゼラチンについて規定する。

Animal glues and gelatins

BS 1203:2001 热固酚醛和氨基塑料木材胶粘剂.分类和试验方法

This British Standard specifies the technical requirements and methods of test for adhesives based on synthetic resins of the phenolic and aminoplastic types, with or without additional hardeners and extenders. The standard does not in any way apply to adhesives based on resins of types other than phenolic or aminoplastic and should not be quoted for these other materials. The properties of the adhesives are determined by tests made on beechwood joints with thin gluelines. The failing forces obtained on the test pieces prescribed cannot be converted into terms of stress values (i.e. pascals) for structural calculations. Resins sometimes require a hardener to be added by the user. In this situation, this standard covers the combination of resin and hardener. If the resin and hardener are sold separately, neither by itself can be said to conform to any of the specified durability classes.

Hot-setting phenolic and aminoplastic wood adhesives - Classification and test method

NAVY QPL-AMS-A-25463-1-2001 夹层金属结构用膜形胶粘剂

This list has been prepared for use by or for the Government in the acquisition of products covered by the subject non-Government standard and such listing of a product is not intended to and does not connote endorsement of the product by the Department of Defense.

ADHESIVE, FILM FORM, METALLIC STRUCTURAL, SANDWICH CONSTRUCTION [Superseded: NAVY QPL-25463 -31, NAVY QPL-25463 -30 (1), NAVY QPL-25463 -30, NAVY QPL-25463 -29, NAVY QPL-25463 -28 (1), NAVY QPL-25463 -28, NAVY QPL-25463 -27, NAVY QPL-25463 -26,

NAVY MMM-A-185 B NOTICE 2-2001 用于粘纸的橡胶粘合剂[代替 NAVY MMM-A-00185 A]

This notice should be filed in front of MMM-A-185B, dated 15 July 1999. MMM-A-185B is inactive for new design and is no longer used except for replacement purposes.

ADHESIVE, RUBBER (FOR PAPER BONDING) [Use In Lieu Of: NAVY MMM-A-00185 A]

NAVY MMM-A-1931 NOTICE 1-2001 银芯传导环氧粘合剂

This notice should be filed in front of MMM-A-1931, dated 19 September 1975.MMM-A-1931 is inactive for new design and is no longer used except for replacement purposes.

ADHESIVE, EPOXY, SILVER FILLED, CONDUCTIVE

NAVY MMM-A-1617 B NOTICE 1-2001 橡胶基座粘合剂的一般用途

This notice should be filed in front of MMM-A-1617B, dated 10 February 1995.

ADHESIVE, RUBBER BASE, GENERAL PURPOSE

NAVY QPL-MMM-A-1617-4 NOTICE 1-2001 通用橡胶基粘合剂

Qualified Products List QPL-MMM-A-1617-4, dated 30 November 1995, is hereby inactive for new design.

ADHESIVE, RUBBER BASE, GENERAL PURPOSE

NAVY MMM-A-1058 A NOTICE 1-2001 加压分配器内部橡胶基座粘合剂 [代替NAVY MMM-A-001058]

This notice should be filed in front of MMM-A-1058A, dated 16 January 1975.

ADHESIVE, RUBBER BASE (IN PRESSURIZED DISPENSERS) [Use In Lieu Of: NAVY MMM-A-001058]

NAVY MMM-A-134 NOTICE 1-2001 用于金属-金属结构粘结的环氧树脂粘合剂

This notice should be filed in front of MMM-A-134, dated 15 July 1999.

ADHESIVE, EPOXY RESIN, METAL TO METAL STRUCTURAL BONDING

NAVY QPL-MMM-A-134-11 NOTICE 1-2001 金属与金属结构之间粘结环氧树脂粘合剂

Qualified Products List QPL-MMM-A-134-10, dated 28 May 1997, is hereby inactive for new design.

ADHESIVE, EPOXY RESIN, METAL TO METAL STRUCTURAL BONDING

NAVY MMM-A-138 B NOTICE 2-2001 金属-木材结构粘合剂[代替NAVY MMM-A-00138]

This notice should be filed in front of MMM-A-138B, dated 5 November 1991.

ADHESIVE, METAL TO WOOD, STRUCTURAL [Use In Lieu Of: NAVY MMM-A-00138]

ARMY A-A-59109 B-2001 环氧树脂基粘合剂

This commercial item description covers one type of adhesive consisting of an epoxy resin base and an amine type curing agent.

ADHESIVE, EPOXY RESIN BASE

ASTM D1583-01 干粘膜中氢离子浓度的标准试验方法

The pH of an adhesive may be a factor whereby the adherends or the adhesive itself may be adversely affected in time by the acidity or alkalinity.1.1 This test method covers determination of the hydrogen ion concentration (pH), acidity, or alkalinity, of organic adhesives in the cured dry film form. This test method is not designed to apply to pressure-sensitive adhesives. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Hydrogen Ion Concentration of Dry Adhesive Films

DLA A-A-59692-2001 耐水粘合剂(粘合纤维板箱) [取代：DLA MMM-A-250 C CANC NOTICE 2, DLA MMM-A-250 C VALID 公告 1, DLA MMM-A-250 C (1), DLA MMM-A-250 C, DLA MMM-A-250 B, DLA MMM-A-250 A]

This Commercial Item Description (CID) covers water-resistant adhesives intended for closure of fiberboard boxes, cartons, and cases.

ADHESIVE, WATER-RESISTANT (FOR CLOSURE OF FIBERBOARD BOXES) [Superseded: DLA MMM-A-250 C CANC NOTICE 2, DLA MMM-A-250 C VALID NOTICE 1, DLA MMM-A-250 C (1), DLA MMM-A-250 C, DLA MMM-A-250 B, DLA MMM-A-250 A]

CSA C22.2 No.0.15-01-2001 不干胶标签.第3版

Adhesive Labels Third Edition

Adhesive Labels Third Edition

ASTM D3652/D3652M-01(2006) 压敏胶纸带厚度的标准试验方法

Thickness is an important property of tapes, and this dimension is important for certain end uses. This test method is useful for quality control and for acceptance testing for conformance to specifications.1.1 This test method covers the determination of the thickness of pressure-sensitive tapes at standard conditions.1.2 The values stated in either SI or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system must be used independently, without combining values in any way.1.3 This test method is intended to replace AFERA 4006 and PSTC 33.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Thickness of Pressure-Sensitive Tapes

ASTM D1583-01(2008) 干粘膜中氢离子浓度的测试方法

The pH of an adhesive may be a factor whereby the adherends or the adhesive itself may be adversely affected in time by the acidity or alkalinity.1.1 This test method covers determination of the hydrogen ion concentration (pH), acidity, or alkalinity, of organic adhesives in the cured dry film form. This test method is not designed to apply to pressure-sensitive adhesives. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Hydrogen Ion Concentration of Dry Adhesive Films

NAVY MIL-PRF-24793 A-2001 一部分紫外固化的光纤粘合剂

This specification covers the requirements of a liquid adhesive for bonding optical fibers to glass fiber optic splice, connector, and terminus ferrules.

ADHESIVE, UV CURABLE, ONE PART, FIBER OPTICS

ASTM D2235-01 丙烯腈-丁二烯-苯乙烯共聚物(ABS)塑料管和配件用液态粘结剂的标准规范

1.1 This specification covers solvent cement for joining acrylonitrile-butadiene styrene (ABS) plastic pipe and fittings for pressure and nonpressure systems. 1.2 Recommendation for using solvent cement for joining acrylonitrile-butadiene-styrene (ABS) plastic pipe and fittings is given in Appendix X1. Satisfactory joining of pipe and fittings cannot be made in the presence of water, as water destroys the bonding ability of solvent cement; therefore, all materials must be dry for satisfactory joining. 1.3 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.5 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings

ASTM D1579-01 苯酚、间苯二酚和三聚氰胺胶粘剂中填料含量的标准测试方法

It is possible to modify the properties of phenol, resorcinol, and melamine-based adhesives by adding fillers to the adhesive and in doing so affect the way the adhesive performs. This test method makes possible accurate determination of these filler levels for purposes of quality control and characterization of the adhesive.1.1 This test method is suitable for measuring the filler content of phenol, resorcinol, and melamine resin-base adhesives mixed with hardener or catalyst, that set at room, intermediate, and high temperatures. Results are expressed on the basis of the nonvolatile content of the mixed, liquid adhesive.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Filler Content of Phenol, Resorcinol, and Melamine Adhesives