G39 胶粘剂 标准查询与下载

ASTM D2094-00 附着力试验用棒和杆试样制备的标准操作规程

1.1 This practice describes bar- and rod-type butt-joined adhesion test specimens and procedures for preparing and bonding them. The specimens are intended to be used with various adherend materials in like or unlike combinations for determining the strength properties of adhesives in accordance with Test Method D2095.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.3 The values stated in SI units are considered to be the standard. The values in parentheses are for information only.

Standard Practice for Preparation of Bar and Rod Specimens for Adhesion Tests

ASTM D2094-00(2006) 附着力试验用棒和杆试样制备的标准操作规程

The procedures outlined in this practice are designed to standardize the test specimens, surface preparations, combinations of materials, and adhesive selection. Because of the flexibility in the procedure, it is important to have some idea of the kind of properties that will be observed during testing.1.1 This practice describes bar- and rod-type butt-joined adhesion test specimens and procedures for preparing and bonding them. The specimens are intended to be used with various adherend materials in like or unlike combinations for determining the strength properties of adhesives in accordance with Test Method D 2095.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.2 The values stated in SI units are considered to be the standard. The values in parentheses are for information only.

Standard Practice for Preparation of Bar and Rod Specimens for Adhesion Tests

ASTM D2094-00e1 附着力试验用棒和杆试样制备的标准操作规程

1.1 This practice describes bar- and rod-type butt-joined adhesion test specimens and procedures for preparing and bonding them. The specimens are intended to be used with various adherend materials in like or unlike combinations for determining the strength properties of adhesives in accordance with Test Method D2095.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.3 The values stated in SI units are considered to be the standard. The values in parentheses are for information only.

Standard Practice for Preparation of Bar and Rod Specimens for Adhesion Tests

ASTM D6590/D6590M-00(2006) 密封纤维容器和罐用的压敏胶带的标准规范

1.1 This specification covers one type of pressure-sensitive tape for closing and sealing slip cover type containers such as fiber tubes and metal cans.1.2 The values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system must be used independently, without combining values in any way.The following safety hazards caveat pertains only to the test methods portion of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to its use.

Standard Specification for Pressure-Sensitive Tape for Sealing Fiber Containers and Cans

ASTM D1583-00 干粘膜中氢离子浓度的标准试验方法

1.1 This test method covers determination of the hydrogen ion concentration (pH), acidity, or alkalinity, of organic adhesives in the cured dry film form. This test method is not designed to apply to pressure-sensitive adhesives. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Hydrogen Ion Concentration of Dry Adhesive Films

NAVY MMM-A-134 (1)-1999 用于金属-金属结构粘结的环氧树脂粘合剂

The General Services Administration has authorized the use of this amendment which forms a part of MMM-A-134, dated August 17, 1970, by all federal agencies.

ADHESIVE, EPOXY RESIN, METAL TO METAL STRUCTURAL BONDING

NAVY MMM-A-185 B (3)-1999 用于粘纸的橡胶粘合剂

The margins of this amendment are marked with asterisks to indicate where changes from the previous amendment were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous amendment.

ADHESIVE, RUBBER (FOR PAPER BONDING)

HG/T 3659-1999 快速粘接输送带用氯丁胶粘剂

本标准规定了快速粘接输送带用氯丁胶粘剂的要求、试验方法、检验规则、包装、标志、 运输与贮存。 本标准适用于以冷粘工艺粘接具有多层织物带芯的橡胶输送带接头用氯丁胶粘剂。

Polychloroprene Rubber Based Adhesive for Quick Bonding Conveyor Belts

JB/T 4254-1999 液态密封胶

本标准规定了液态密封胶的产品种类、要求、试验方法、包装、标志、贮存及运输。 本标准适用于机械产品各结合防止气体、液体泄漏。

Fluid sealants

DB35/ 329-1999 鞋用聚氨脂胶粘剂

本标准规定了鞋用聚氨酯胶粘剂（以下简称胶粘剂）的技术要求、试验方法、检验规则及标志、标签、使用说明书和包装、运输、贮存。本标准适用于不人为添加苯系物、卤代烃有机溶剂的鞋用聚氨酯胶粘剂。主要用于PVC人造革、天然皮革、硫化橡胶及热塑性弹性体、PU合成革、EVA等材料的粘接。

polyurethane adhesive for shoes

NAVY MIL-PRF-24792 A-1999 两部分环氧光纤粘合剂

This specification covers the requirements of a 100 percent solid epoxy adhesive for bonding optical fibers to metal and ceramic fiber optic connector and terminus ferrules.

ADHESIVE, EPOXY, TWO PART, FIBER OPTICS

ASTM F451-99ae1 丙烯酸骨胶结剂

1.1 This specification covers self-curing resins used primarily for the fixation of internal orthopedic prostheses. The mixture may be used in either the predough or dough stage in accordance with the manufacturer's recommendations.1.2 Units of premeasured powder and liquid are supplied in a form suitable for mixing. The mixture then sets in place.1.3 While a variety of copolymers and comonomers may be incorporated, the composition of the set cement shall contain poly(methacrylic acid esters) as its main ingredient.1.4 This specification covers compositional, physical performance, and biocompatibility as well as packaging requirements. The biocompatibility of acrylic bone cement as it has been traditionally formulated and used has been reported in the literature (1, 2).1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Acrylic Bone Cement

ASTM D6412/D6412M-99(2005) 用于粘结金属和非金属材料的环氧(柔性)粘结剂的标准规范

1.1 The specification covers a two-part modified epoxy paste adhesive for bonding metallic and nonmetallic materials. The adhesive should be suitable for forming bonds that can withstand environmental exposure to temperatures from -184 to 82 176C (-300 to 180 176F) when exposed to an expected combination of stress, temperature, and relative humidity to be encountered in service. Note 1-When coordinated through the Department of Defense (DoD) and the National Aeronautics and Space Administration (NASA), this practice will be a direct replacement of MIL-A-82720 (OS), MIS-26872 and MSFC-SPEC-2037. 1.2 The values stated in SI units or inch-pound units are to be regarded separately as standard. Within the text, the inch-pound units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification. 1.3 The following precautionary statement pertains to the test method portion only, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Epoxy (Flexible) Adhesive for Bonding Metallic and Nonmetallic Materials

ASTM D4689-99(2005) 酪蛋白型胶粘剂标准规范

1.1 This specification covers casein and other protein-blend adhesives for use adhering wood to wood. The adhesive type covered by this specification is a dry powder or granular product comprising a mixture of casein, or casein and other protein source, with the necessary dry chemicals to effect solution when the mixture is added to water. Note 18212;Although the term casein adhesive is used throughout this specification, historically, the adhesive subclass described in 1.1 has been known as casein glue. See Terminology D 907, adhesive types. 1.2 Limitations8212; Cooked casein adhesives are not covered by this specification.1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.4 The following safety hazards caveat pertains only to the test method portion, Sections 8 through 16, of this specification:This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Adhesive, Casein-Type

ASTM D4690-99(2005) 脲甲醛树脂胶粘剂标准规范

1.1 This specification covers three types of urea-formaldehyde thermosetting resin adhesives suitable for use on wood, wood-based substrates, or plastic laminates.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are provided for information only.1.3 The requirements for the adhesive are based on tests of physical properties including viscosity, density, nonvolatile content, pH, insoluble matter, amylaceous matter, mixing properties, working life, and on strength properties, including dry shear strength in lumber-type joints, dry and wet shear strength in plywood-type joints, and all strength tests at the end of the storage life certified by the manufacturer.1.4 The following safety hazards caveat pertains only to the test method portion, Sections 8 through 13, of this specification:This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Urea-Formaldehyde Resin Adhesives

ASTM D4688-99 评定榫接木材粘结用结构胶粘剂的标准试验方法

1.1 These test methods cover the evaluation of adhesives for finger jointing lumber used in the manufacture of structural glued laminated timber. They include tests of the tensile strength of joints; dry with no treatment, wet after one vacuum-pressure soak treatment, and wet after cyclic boil-dry treatment. 1.2 The values stated in inch-pound units are to be regarded as the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Evaluating Structural Adhesives for Finger Jointing Lumber

ASTM F451-99a 丙烯酸骨胶结剂

1.1 This specification covers self-curing resins used primarily for the fixation of internal orthopedic prostheses. The mixture may be used in either the predough or dough stage in accordance with the manufacturer's recommendations. 1.2 Units of premeasured powder and liquid are supplied in a form suitable for mixing, which then sets in place. 1.3 While a variety of copolymers and comonomers may be incorporated, the composition of the set cement shall contain poly(methacrylic acid esters) as its main ingredient. 1.4 This specification covers compositional, physical performance, and biocompatibility as well as packaging requirements. The biocompatibility of acrylic bone cement as it has been traditionally formulated and used has been reported in the literature (1, 2). 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Acrylic Bone Cement

ASTM D4690-99 脲甲醛树脂胶粘剂标准规范

1.1 This specification covers three types of urea-formaldehyde thermosetting resin adhesives suitable for use on wood, wood-based substrates, or plastic laminates. 1.2 The requirements for the adhesive are based on tests of physical properties including viscosity, density, nonvolatile content, pH, insoluble matter, amylaceous matter, mixing properties, working life, and on strength properties, including dry shear strength in lumber-type joints, dry and wet shear strength in plywood-type joints, and all strength tests at the end of the storage life certified by the manufacturer. 1.3 The following safety hazards caveat pertains only to the test method portion, Sections 8 through 13, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Urea-Formaldehyde Resin Adhesives

ASTM D1879-99 暴露在高能辐射下的胶粘剂样品的标准操作规程

1.1 The purpose of this practice is to define conditions for the exposure of polymeric adhesives in bonded specimens to high-energy radiation prior to determination of radiation-induced changes in physical or chemical properties. This recommended practice specifically covers the following kinds of radiation: gamma or X-ray radiation, electron or beta radiation, neutrons, and mixtures of these such as reactor radiation. 1.2 This practice specifies only the conditions of irradiation but does not cover the preparation of test specimens, testing conditions, or the evaluation of test. These are covered in the various ASTM methods or specifications for specific materials. 1.3 This practice covers procedures for the following five types of exposure: Procedure A -Exposure at ambient conditions. Procedure B -Exposure at controlled temperature. Procedure C -Exposure in a medium other than air. Procedure D- Exposure under load. Procedure E- Exposure combining two or more of the variables listed in Procedures A to D. Note 1-The problems of measuring the properties of materials during irradiation involve shielding and remote control facilities and are, therefore, not considered in this practice.

Standard Practice for Exposure of Adhesive Specimens to High-Energy Radiation

ASTM D4688-99(2005) 评定榫接木材粘结用结构胶粘剂的标准试验方法

This test method is specifically designed to measure the performance of adhesives in finger joints manufactured under production line conditions. The results of the test method may be used to certify an adhesive as suitable for finger jointing lumber under production-line conditions where the intended end use of the finger jointed lumber will be in a structural glued laminated timber. When the test results are to be used for certification of an adhesive for this purpose, use a standard wood species and a standard finger profile. Standard species may be found in Table 1 of Specification D 2559. Two standard finger profiles commonly used in the manufacture of structural glued laminated timber industry are shown in Fig. 1.3 This test method is not intended for quality control as the test assemblies are selected for their absence of defects usually found in run-of-the-mill lumber and finger joints. Note8212;Recommended by American Institute of Timber Construction.3 FIG. 1 Standard Joint Profiles for Certification Tests1.1 This test method is designed to evaluate adhesives for finger jointing lumber used in the manufacture of structural glued laminated timber. It tests the tensile strength of joints under the following treatments; dry with no treatment, wet after one vacuum-pressure soak treatment, and wet after cyclic boil-dry treatment.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Evaluating Structural Adhesives for Finger Jointing Lumber