G39 胶粘剂 标准查询与下载

ASTM C557-99 在木结构上固定石膏护墙板用胶粘剂标准规范

1.1 This specification covers minimum standards for adhesives intended for bonding the back surface of gypsum wallboard to wood framing members. 1.2 This specification also covers test requirements and test methods for the adhesive used for the application of all thicknesses of gypsum wallboard.

Standard Specification for Adhesives for Fastening Gypsum Wallboard to Wood Framing

ASTM D4689-99 酪蛋白型胶粘剂标准规范

1.1 This specification covers casein and other protein-blend adhesives for use adhering wood to wood. The adhesive type covered by this specification is a dry powder or granular product comprising a mixture of casein, or casein and other protein source, with the necessary dry chemicals to effect solution when the mixture is added to water. Note 1-Although the term casein adhesive is used throughout this specification, historically, the adhesive subclass described in 1.1 has been known as casein glue. See Terminology D907, adhesive types . 1.2 Limitations -Cooked casein adhesives are not covered by this specification. 1.3 The values stated in inch-pound units are to be regarded as the standard. 1.4 The following safety hazards caveat pertains only to the test method portion, Sections 8 through 16, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Adhesive, Casein-Type

DIN EN 1721:1998 纸张和纸板、包装材料和卫生产品的粘结剂.压敏性粘接剂表面粘性的测量.按照滚球法测量表面粘性

Adhesives for paper and board, packaging and disposable sanitary products - Tack measurement for pressure sensitive adhesives - Determination of rolling ball tack; German version EN 1721:1998

ISO 9665:1998 粘合剂 动物胶 取样和试验方法

This International Standard specifies the methods to be used for sampling and testing bone and skin glues in the form of powder, granules, pearls or cubes. NOTE 1 The methods may be extended to the testing of other forms of animal glues by suitable calculation of the equivalent dry glue content. The precision of the test methods included in this International Standard is not known because interlaboratory data are not available. When interlaboratory data are obtained, precision statements will be added to the corresponding test methods at the next revision. NOTE 2 For details of precision statements, refer to ISO 5725-1:1994, Accuracy (trueness and precision) of measurement methods and results — Part 1: General principles and definitions.

Adhesives - Animal glues - Methods of sampling and testing

IPC TM-650 2.3.17.1-1998 胶粘剂涂膜树脂流动和无载体胶粘剂胶片 修订版D

IPC Standards and Publications are designed to serve the public interest through

Resin Flow of Adhesive Coated Films and Unsupported Adhesive Films Revision B

IPC TM-650 2.3.37-1998 胶粘剂涂布介质薄膜的挥发份含量 修订版B

Material in this Test Methods Manual was voluntarily established by Technical Committees of the IPC. This material is advisory only and its use or adaptation is entirely voluntary. IPC disclaims all liability of any kind as to the use, application, or adaptation of this material. Users are also wholly responsible for protecting themselves against all claims or liabilities for patent infringement. Equipment referenced is for the convenience of the user and does not imply endorsement by the IPC.

Volatile Content of Adhesive Coated Dielectric Films Revision B

IPC TM-650 2.4.19-1998 柔性印刷线路材料拉伸强度和延伸率

Because of a need for technical information, and to develop standards in the field of printed wiring, the IPC was organized in 1957 by independent producers of PWBs and began as The Institute of Printed Circuits.

Tensile Strength and Elongation, Flexible Printed Wiring Materials Revision C

BS ISO 14615:1998 粘合剂.结构粘合连接的耐久性.在负载情况下暴露于湿度和温度之中

This International Standard describes the equipment and the test procedure used to evaluate the durability of adhesive-bonded joints exposed simultaneously to heat, humidity and load. This method is intended for the evaluation of structural and semi-structural adhesives used in hot and/or humid environments. It is particularly suitable for metal, composite and plastic adherends.

Adhesives - Durability of structural adhesive joints - Exposure to humidity and temperature under load

ASTM D6295/D6295M-98(2004) 轻载压敏膜带的非必需性的标准试验方法

Pressure-sensitive film tapes are supplied in roll form. For such a tape to be useful a strip of the tape must be easily dispensed or severed from the roll by means of a cutter found on most dispensers. This test method is a means of measuring the ease of this severing or dispensing of the tape. This test method provides information that can be used in material specifications for product design and quality assurance applications. It can be used in comparing different tape products on specific dispensing blades. This test method may be suited for office and stationery and tapes with acetate, cellophane, or light-duty plastic backings. Some tapes may be shown to be difficult to dispense under these conditions yet are readily dispensable with other dispensing systems. Note 18212;Backings described in CID A-A-113 are typical backings.1.1 This test method covers the measurement of the force and elongation required to dispense pressure-sensitive film tape on a 1-in. core intended for office and stationery applications from a desk-top dispenser.

Standard Test Method for Dispensability of Light-Duty Pressure-Sensitive Film Tape

ASTM D6252/D6252M-98(2011) 测试90176度角上压敏标签毛坯剥落附着力的标准试验方法

This test method is a tool for quality assurance use. Given a pressure-sensitive label stock and a requirement in terms of the minimum or maximum peel adhesion value expected for this label stock, the data from the test can be used in conjunction with acceptance criteria. This test method can show the relative bond strength of a given label stock to one or more surfaces of varied material and texture as compared to the standard stainless steel panel. Substitution of panels representative of the proposed substrates for the standard stainless steel panel would be acceptable for this procedure.1.1 This test method covers the measurement of the peel adhesion of pressure-sensitive label stocks. This test method gives a measure of the adherence to a standard steel substrate or to other surfaces of interest for a pressure-sensitive label stock. 1.2 This test method provides a means of assessing the uniformity of the adhesion of a given type of pressure-sensitive label stock. The assessment may be within a sheet or roll, between sheets or rolls, or between production lots. 1.3 Variations in the label stock facestock and adhesive can affect the response; therefore, this test method cannot be used to pinpoint the specific cause(s) of nonuniformity. 1.4 This test method may not be appropriate to test label stocks having either stiff backings or backings showing a high stretch at low forces. These characteristics could result in a high variability of the test response, which is not a true indication of the real nature of the adhesive bond. 1.5 The values stated in either SI or inch-pound units are to be regarded separately as the standard. The values stated in each system may not be exact equivalents; therefore, each system must be used independently, without combining values in any way. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Peel Adhesion of Pressure-Sensitive Label Stocks at a 90&176 Angle

ASTM D5375/D5375M-98(2011) 从压敏标签材料上高速去除衬里的标准试验方法

These test methods are a tool for development and quality assurance use. Given a specific pressure-sensitive label and liner and a requirement in terms of the minimum for maximum peel value expected for this liner removal from the label, the data from the test can be used in conjunction with acceptance criteria.1.1 These test methods cover the measurement of the adherence of the release liner to the adhesive of a pressure-sensitive adhesive label. 1.2 These test methods provide means of assessing the uniformity of the adhesion to the liner of a given type of pressure-sensitive label. The assessment may be within a sheet or roll between sheets or rolls or between production lots. 1.3 Variation in the label backing, liner, liner release coating, adhesive, and adhesive coating weight, affect the response. Therefore, these methods cannot be used to pinpoint the specific cause(s) of nonuniformity. 1.4 These test methods may not be appropriate to test labels having either relatively stiff backings or stiff liners, or backings showing high stretch at low forces. These characteristics will result in a high variability of the test response that is not a true indication of the real nature of the adhesive bond. 1.5 The values stated in either SI or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system must be used independently, without combining values in any way. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Liner Removal at High Speeds from Pressure-Sensitive Label Stock

ASTM D4317-98(2004) 聚乙酸乙烯酯乳状胶粘剂

1.1 This specification covers polyvinyl acetate or polyvinyl acetate copolymer resin emulsion adhesives suitable for use on wood, wood-based substrates, or plastic laminates. It does not cover the group of polyvinyl-based adhesives which are suitable for bonding flexible films.1.2 The adhesives are classified at three performance levels in accordance with water-resistance as shown in and . See Section for a description of the expected exposure conditions for each class of adhesive. See for a classification of typical end products that are manufactured using adhesives at the three performance levels covered by this specification.1.3 The following index is provided as a guide to the test methods portion of this specification:SectionTests for Physical PropertiesViscosityDensity NonvolatilespH Tests for Adhesive BondBlock Shear Strength, CompressionPlywood Shear Tests1.4 The values stated in SI units are to be regarded as the standard. The values given in parenthesis are for information purposes only.1.5 The following safety hazards caveat pertains only to the test method portion, Sections 9 and 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Polyvinyl Acetate-Based Emulsion Adhesives

ASTM E1555-98 用于夹层板修补的结构膏胶粘剂标准规范

1.1 This specification defines those characteristics that are required of adhesives to be used in the repair of sandwich panels for durable, rigidwall, relocatable shelters. 1.1.1 This specification covers two-part epoxy adhesive suitable for bonding aluminum alloy facings to nonmetallic core and core to core in the repair of durable rigidwall relocatable shelters. The adhesive shall be suitable for forming bonds that will withstand exposure to temperatures from -54 to 93176C (-65 to 199176F) and high relative humidity and will also withstand the combinations of stress, temperature, and relative humidity that are expected to be encountered in service. The adhesive shall also be suitable for the bonding of panel inserts and edge attachments. 1.2 The values stated in SI units are to be regarded as the standard where only SI units are given, or where SI units are given first followed by inch-pound units; where inch-pound units are given first followed by SI units, the inch-pound units are to be regarded as the standard. 1.3 The following safety hazards caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Structural Paste Adhesive for Sandwich Panel Repair

ASTM D4317-98 聚乙酸乙烯酯乳状胶粘剂

1.1 This specification covers polyvinyl acetate or polyvinyl acetate copolymer resin emulsion adhesives suitable for use on wood, wood-based substrates, or plastic laminates. It does not cover the group of polyvinyl-based adhesives which are suitable for gluing flexible films. 1.2 The adhesives are classified at three performance levels in accordance with water-resistance as shown in Tables 1 and 2. See Section 5 for a description of the expected exposure conditions for each class of adhesive. See Table X1.1 for a classification of typical end products that are manufactured using adhesives at the three performance levels covered by this specification. 1.3 The following index is provided as a guide to the test methods portion of this specification: Section Tests for Physical Properties 9 Viscosity 9.1.1 Density 9.1.2 Nonvolatiles 9.1.3 pH 9.1.4 Tests for Adhesive Bond 10 Block Shear Strength, Compression 10.2 Plywood Shear Tests 10.3 1.4 The values stated in inch-pound units are to be regarded as the standard. 1.5 The following safety hazards caveat pertains only to the test method portion, Sections 9 and 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Polyvinyl Acetate-Based Emulsion Adhesives

ASTM D6252/D6252M-98(2004) 压敏标签在90-176°角度的剥离粘附力的标准试验方法

This test method is a tool for quality assurance use. Given a pressure-sensitive label stock and a requirement in terms of the minimum or maximum peel adhesion value expected for this label stock, the data from the test can be used in conjunction with acceptance criteria. This test method can show the relative bond strength of a given label stock to one or more surfaces of varied material and texture as compared to the standard stainless steel panel. Substitution of panels representative of the proposed substrates for the standard stainless steel panel would be acceptable for this procedure.1.1 This test method covers the measurement of the peel adhesion of pressure-sensitive label stocks. This test method gives a measure of the adherence to a standard steel substrate or to other surfaces of interest for a pressure-sensitive label stock. 1.2 This test method provides a means of assessing the uniformity of the adhesion of a given type of pressure-sensitive label stock. The assessment may be within a sheet or roll, between sheets or rolls, or between production lots. 1.3 Variations in the label stock facestock and adhesive can affect the response; therefore, this test method cannot be used to pinpoint the specific cause(s) of nonuniformity. 1.4 This test method may not be appropriate to test label stocks having either stiff backings or backings showing a high variability of the test response, which is not a true indication of the real nature of the adhesive bond. 1.5 The values stated in either SI or inch-pound units are to be regarded spearately as the standard. The values stated in each system may not be exact equivalents; therefore, each system must be used independently, without combining values in any way. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Peel Adhesion of Pressure-Sensitive Label Stocks at a 90176 Angle

ASTM D2851-98 液态光学胶粘剂

1.1 This specification covers liquid optical adhesive for use in bonding glass to glass or other transparent adherends. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are provided for information purposes only. 1.3 The following precautionary caveat pertains only to the test method portion, Section 5, of this specification: This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in the Note in 6.1.1.

Standard Specification for Liquid Optical Adhesive

ASTM D6295/D6295M-98(2011) 轻型压敏胶带可省约性的标准试验方法

Pressure-sensitive film tapes are supplied in roll form. For such a tape to be useful a strip of the tape must be easily dispensed or severed from the roll by means of a cutter found on most dispensers. This test method is a means of measuring the ease of this severing or dispensing of the tape. This test method provides information that can be used in material specifications for product design and quality assurance applications. It can be used in comparing different tape products on specific dispensing blades. This test method may be suited for office and stationery and tapes with acetate, cellophane, or light-duty plastic backings. Some tapes may be shown to be difficult to dispense under these conditions yet are readily dispensable with other dispensing systems. Note 18212;Backings described in CID A-A-113 are typical backings.1.1 This test method covers the measurement of the force and elongation required to dispense pressure-sensitive film tape on a 1-in. core intended for office and stationery applications from a desk-top dispenser. 1.2 The values stated in either SI or inch-pound units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. 1.3 This standard does not propose to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Dispensability of Light-Duty Pressure-Sensitive Film Tape

ASTM D1779-98(2004) 声学材料用胶粘剂的标准规范

1.1 This specification covers an adhesive for bonding prefabricated acoustical materials to the inside walls and ceilings of rooms in buildings. This adhesive is required to maintain a tensile adhesion (bond strength) of not less than 3.45 104 dynes/cm2 (1/2 lb/in.2) for a long period of time under the temperature and moisture conditions likely to be encountered and to maintain sufficient plasticity to allow for movement of parts of the building as it ages.Note 18212;Cleanliness of Surface-The surface to which the acoustical material is applied with the adhesive should be clean, sound, and dry. Surface coatings should be removed if their nature indicates an unsatisfactory installation, so that the adhesive can be applied to the base. When the adhesive is to be applied on a painted surface, test tile should be applied for 48 h to determine suitable adherence of the coating by examination. Acoustical adhesives are not intended to be applied to surfaces that are moist and that have an alkaline reaction, or that may later become moist or alkaline. Such surfaces, as concrete or plaster, should be properly dried and aged before applying the adhesive.Note 28212;Load-This adhesive is not recommended as a sole means of holding acoustical materials weighing more than 121 kg/m 2 (21/2 lb/ft2) to ceiling surfaces.Note 38212;Amount and Condition of Material-It is recommended that sufficient adhesive be used so that there is a contact surface of not less than 1.2 104 cm2/m2 (20 in.2/ft2) of acoustical material, with a minimum thickness of 0.3 cm (1/8 in.) and that the adhesive be applied in four separate nearly spherical portions of approximately equal size near the corners for a standard 30.5 by 30.5-cm (12 by 12-in.) tile. Fewer than or more than four portions for 30.5 by 30.5-cm tile are not recommended due to difficulty in leveling and in securing effective contact area on all portions. Adhesives that are hard, or do not wet the surface, or are difficult to spread should not be used.Note 4Rigidity of Base Surfaces-It is necessary that the material forming the base to which the adhesive is attached should be relatively smooth, firm, and rigid. If the pressure of applying tile and adhesive causes the base material to deflect excessively, tile previously applied may have their adhesive bond broken. This occurs on some types of gypsum board suspension systems.Note 5Aging-To date, no accelerated aging tests for adhesives have been developed to duplicate exactly aging in service. The aging tests in this specification are designed to accelerate the aging process and to test various manifestations of aging, and are intended to be satisfactory for comparing one adhesive with another; they do not necessarily reflect aging characteristics on an absolute basis. Purchasers of adhesives should receive from the manufacturer additional warranties and assurances of performance of the adhesive under normal aging.Note 68212;Erection Practices-Proper erection techniques are essential for proper performance of any acoustical adhesive. Use of a material meeting this specification will not in itself guarantee satisfactory performance. Only when tiles are applied by skilled and experienced workers following instructions from the manufacturer can the purchaser be assured of satisfactory performance of an adhesive.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Adhesive for Acoustical Materials

ASTM D3715/D3715M-98(2004) 压合带的质量保证的标准实施规程

1.1 This practice contains uniform quality assurance provisions for pressure-sensitive tapes and establishes sampling plans and procedures for acceptance inspection.1.2 Limitations1.2.1 This practice only includes procedures for when an upper or a lower specification limit is given. It does not provide for double, both minimum and maximum, specification limits. Note 1When double specification limits are given (applies to variables testing only), use may be made of Table C-3 and Example C-3 of ANSI/ASQC Z1.9.1.2.2 The variables sampling plans apply to a single quality characteristic. Having obtained the sample and the responses to the physical property tests, acceptance is determined on one quality characteristic at a time. The process is repeated for each additional characteristic.1.2.3 The variables sampling plans require that the response to each quality characteristic is normally distributed either directly or by transformation. If this is not known, the potential user of this practice should seek the counsel of someone with sufficient understanding of statistical techniques to provide that information.1.3 The values stated in either SI or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system must be used independently, without combining values in any way.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Quality Assurance of Pressure-Sensitive Tapes

IPC TM-650 5.5.3.7-1998 试样E绝缘电阻

This test method is designed to determine the capability of HDI materials and other dielectrics to withstand moisture induced stress as applied by extended time in a pressure vessel. For laminated constructions, the results may be affected by the process conditions.

Specimen E Insulation Resistance