G39 胶粘剂 标准查询与下载

JIS A 5547:1996 泡沫塑料板用粘合剂

Adhesives for plastic foam board

JIS A 5538:1996 护墙板和天花板用粘合剂

Adhesives for wall and ceiling boards

JIS A 5537:1996 固定木砌块用粘合剂

Adhesives for anchoring wooden blocks

DIN EN 12024:1996 胶粘带.耐高温高空气湿度的测定

The document specifies a method to obtain an indication of the behaviour of the adhesive tape under specified conditions of elevated temperature and high humidity.

Self adhesive tapes - Measurement of resistance to elevated temperature and humidity; German version EN 12024:1996

DIN EN 12025:1996 胶粘带.摆锤法测量撕裂强度

The document specifies the method to measure the force required to tear certain types of adhesive tapes under standard test conditions. Details of the test method depend upon the width of the adhesive tape under test. For adhesive tapes less than 63,5 mm width it is necessary to use Annex A (normative).#,,#

Self adhesive tapes - Measurement of tear resistance by the pendulum; German version EN 12025:1996

DIN EN 12027:1996 胶粘带.耐燃性测定

The document specifies a method to mesure the ability of an adhesive tape to withstand exposure to flame. A freely suspended piece of adhesive tape is ignited by means of a fuse. The flame resistance of the adhesive tape is measured by noting the time taken for the flame to go out and the length of adhesive tape burnt.

Self adhesive tapes - Measurement of flame resistance; German version EN 12027:1996

DIN EN 12026:1996 胶粘带.高速开卷力测量

Self adhesive tapes - Measurement of the unwinding force at high speed; German version EN 12026:1996

DIN EN 12036:1996 胶粘带.胶粘封条的溶剂渗透

Self adhesive tapes - Solvent penetration into adhesive masking tapes; German version EN 12036:1996

DIN EN 12035:1996 胶粘带.胶粘带头标记

The document specifies a method to measure flagging which may occur under specified conditions. Knowledge of the flagging is useful in determining whether the adhesion of the adhesive tape to a backing of the same adhesive tape is adequate for applications where unwinding could occur. The flagging may occur under normal conditions, during the curing cycle of thermosetting adhesives or during immersion in liquids.#,,#

Self adhesive tapes - Flagging of adhesive tape; German version EN 12035:1996

DIN EN 12034:1996 胶粘带.粘合带卷长度测量

The document specifies a method to measure the length of adhesive tape on a roll. For non extensible adhesive tapes the length measured by this method shall be the same as the length after unrolling. For extensible adhesive tapes the length after unrolling shall be greater if the adhesive tape is stretched irreversibly by unrolling. It is also possible for an extensible adhesive tape to measure less after unrolling if stress built manufacture recovers after unrolling. This is important for all adhesive tapes with elongation at break of 80 % or greater.

Self adhesive tapes - Measurement of the length of a roll of adhesive tape; German version EN 12034:1996

DIN EN 12033:1996 胶粘带.热硬化后胶粘带粘着强度测量

The document specifies a method to observe the bonding of a thermosetting adhesive tape in a hot atmosphere.

Self adhesive tapes - Measurement of bonding of thermosetting adhesive tapes after curing; German version EN 12033:1996

DIN EN 12032:1996 胶粘带.热硬化中胶粘带粘着强度测量

The document specifies a method to observe the bonding of a thermosetting adhesive tape during the thermosetting process. The temperature and duration for each test shall be as the manufacturer's instructions for bonding the relevant adhesive tape.

Self adhesive tapes - Measurement of bonding of thermosetting adhesive tapes during curing; German version EN 12032:1996

DIN EN 12031:1996 胶粘带.断裂强度测量

The document specifies a method to measure the hydrostatic pressure required to burst an adhesive tape.

Self adhesive tapes - Measurement of bursting strength; German version EN 12031:1996

DIN EN 12030:1996 胶粘带.耐冲击测量

The document specifies the method to determine the ability of an adhesive tape to resist impact forces. An adhesive tape may posses adequate breaking and tear strengths to withstand a steady force, but it may lack sufficient impact strength to withstand the shock forces sometimes experienced in use. The maximum width of adhesive tape tested by thids method is 25 mm. For rolls of adhesive tape of this width or less, the impact resistance measured corresponds to that of adhesive tape as supplied commercially, i.e. with factory-cut edges.#,,#

Self adhesive tapes - Measurement of impact resistance; German version EN 12030:1996

DIN EN 12029:1996 胶粘带.水溶腐蚀性离子测定

The document specifies a method to give an indication of the ability of an adhesive tape to cause corrosion. If amounts of water-soluble ions are negligible (pH near neutrality and low conductivity of aqueous extract) this indicates that the adhesive tape is suitable for applications where corrosion must be avoided. Adhesive tapes with higher concentrations of water-soluble ions may cause corrosion in use. This test may be useful for electrical applications where the adhesive tape is in contact with metallic surfaces.

Self adhesive tapes - Determination of the water-soluble corrosive ions; German version EN 12029:1996

DIN EN 12028:1996 胶粘带.静力伸长测量

The document specifies the method to mesure the elongation of an adhesive tape under a low tension maintained over a relatively short period. This method is intended to give an indication to the user of the elongation of an adhesive tape under tension in use. This test is particularly applicable to adhesive tapes based on highly stretchable backings.

Self adhesive tapes - Measurement of elongation under static load; German version EN 12028:1996

HG/T 2814-1996 通用型聚酯聚氨酯胶粘剂

本标准规定了通用型聚酯聚氨酯I型胶粘剂的技术要求、试验方法、检验规则、标志、包装、运输、贮存。 本标准适用于由甲、乙二组份调合的室温固化的通用型聚酯聚氨酯I型胶粘剂。

General Purpose Polyester Polyurethane Adhesive

ASTM D2235-96a 丙烯腈-丁二烯-苯乙烯共聚物(ABS)塑料管和配件用液态粘结剂的标准规范

1.1 This specification covers solvent cement for joining acrylonitrile-butadiene styrene (ABS) plastic pipe and fittings for pressure and nonpressure systems. 1.2 Recommendation for using solvent cement for joining acrylonitrile-butadiene-styrene (ABS) plastic pipe and fittings is given in Appendix X1. Satisfactory joining of pipe and fittings cannot be made in the presence of water, as water destroys the bonding ability of solvent cement; therefore, all materials must be dry for satisfactory joining. 1.3 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.5 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings

ASTM D3833/D3833M-96(2006) 压敏带水蒸气透过性的标准试验方法

The results of this test method will indicate the relative permeability by water vapor of the tape through its smallest dimension (generally normal to the tapersquo;backing). 5.1.1 The pathway for the water vapor parallel to the adhesive-cup interface is great compared to the tapersquo;thickness and the latter is usually the nearly exclusive source of transmitted vapor. 5.1.2 Some tape types allow a relatively free path in a direction normal to the backing or along backing pathways parallel to the adhesive-cup interface allowing the adhesive to become the principal barrier. If the adhesive does not continue to adhere to the cup flange during the exposure periods allowing unintended pathways for water vapor to occur, the measurement should be considered as not having been made. Consequently, the tape might be considered as being inappropriate for use on surfaces like the cup flange under moisture conditions approximating those of the test. Note 18212;It may be that the interest is simply in the tape material as a water vapor barrier. In this case, how well the tape adheres to the cup flange may be of little consequence, and steps to prevent any edge effects are in order. These are referred to in Section 10.1.1 This test method covers one procedure for measuring the water vapor transmission rate of pressure-sensitive tape.1.2 The values stated in either SI or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system must be used independently, without combining values in any way.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Water Vapor Transmission of Pressure-Sensitive Tapes

ASTM D3816/D3816M-96(2007) 压感胶带的水渗透率的标准试验方法

The results of this test method will indicate the relative permeability by water of the tape through its smallest dimension (generally normal to the tapersquo;backing). 5.1.1 The pathway for the water parallel to the adhesive-cup interface is great compared to the tapersquo;thickness and the latter is usually the nearly exclusive source of transmitted water. 5.1.2 Some tape types allow a relatively free path in a direction normal to the backing or along backing pathways parallel to the adhesive-cup interface, allowing the adhesive to become the principal barrier. If the adhesive does not continue to adhere to the cup flange during the exposure periods, allowing unintended pathways for water to occur, the measurement should be considered as not having been made. Consequently, the tape might be considered as being inappropriate for use on surfaces like the cup flange under moisture conditions approximating those of the test. Note 18212;It may be that the interest is simply in the tape material as a water barrier. In this case how well the tape adheres to the cup flange may be of little consequence and steps to prevent any edge effects are in order. These are referred to in Section 10.1.1 This test method provides one procedure for measuring the water penetration rate of 2-in. or wider pressure-sensitive tape.1.2 The values stated in either SI or inch-pound units are to be regarded separately as standard. The values stated in each system may not be equivalent; therefore, each system must be used independently, without combining values in any way.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Water Penetration Rate of Pressure-Sensitive Tapes