G40 橡胶制品综合 标准查询与下载

HG/T 2728-2012 橡胶密度的测定.直读法

警告——使用本标准的人员应有正规实验室工作的实践经验，本标准并未指出所有可能的安全问题，使用者有责任采用适当的安全和健康措施，并保证符合国家有关法规规定的条件。 本标准规定了用直读式密度计测定橡胶密度的两种方法。方法A用机械直读式密度计测量，方法B用电子直读式密度计测量。 本标准适用于密度大于1.00g/cm³实心橡胶的测定，不适用于多孔橡胶和硬质橡胶密度的测定。

Rubber,determination of density.Direct reading method

HG/T 4301-2012 橡胶防霉性能测试方法

警告:使用本标准的人员应有正规实验室工作的实践经验，本标准并未指出所有可能的安全问题，使用者有责任采取适当的安全和健康措施，并保证符合国家有关法规规定的条件。 注意事项：本标准的某些步骤中生成的物质和废料可能对当地的环境有所损害。应制定使用后安全处理的有关文件。 本标准规定了橡胶材料及其制品的防霉性能试验和评价方法。本标准不涉及防霉产品安全性的评价。 本标准适用于橡胶材料及其制品。其他高分子材料及其制品也可参照执行。

Test method for determining resistance of rubber to fungi

HG/T 3321-2012 硫化橡胶弹性模量的测定方法

警告——使用本标准的人员应有正规实验室工作的实践经验，本标准并未指出所有可能的安全问题，使用者有责任采用适当的安全和健康措施，并保证符合国家有关法规规定的条件。 本标准规定了用弹性模量测定器测定硫化橡胶弹性模量的方法。 本标准适用于硫化橡胶。

Vulcanized rubber.Determination of elastic modulus

KS M ISO 4664-1:2012 硫化或热塑性橡胶.动态性能的测定.通用指南

이 표준은 가황 및 열가소성 고무의 동적 특성 측정에 관한 내용을 제안하고 있다. 이는 재

Rubber, vulcanized or thermoplastic－Determination of dynamic properties－Part 1：General guidance

SN/T 3124-2012 橡胶及橡胶制品中酚类防霉剂的测定.高效液相色谱法

本标准规定了橡胶及橡胶制品中酚类防霉剂（五氯苯酚、四氯苯酚、邻苯基苯酚、对硝基苯酚、见附录A）的高效液相色谱检测方法。 本标准适用于橡胶及橡胶制品中五氯苯酚、四氯苯酚、邻苯基苯酚、对硝基苯酚的测定。

Determination of phenols preservatives in rubber and rubber products.High performance liquid chromatography

NF T47-203-2:2012 橡胶、塑料软管和管材.曲挠性和刚性的测量.第2部分:低于环境温度的弯曲试验

Rubber and plastics hoses and tubing - Measurement of flexibility and stiffness - Part 2 : bending tests at sub-ambient temperatures.

NF T47-203-3*NF EN ISO 10619-3:2012 橡胶、塑料软管和管材.曲挠性和刚性的测量.第3部分:高温和低温下的弯曲试验

Rubber and plastics hoses and tubing - Measurement of flexibility and stiffness - Part 3 : bending tests at high and low temperatures.

BS ISO 3384-1:2011+A1:2013 硫化或热塑橡胶. 压缩下应力松弛的测定. 恒温试验

Rubber, vulcanized or thermoplastic. Determination of stress relaxation in compression. Testing at constant temperature

NF T47-404-3:2012 橡胶涂覆胶辊.表面硬度的测量.第3部分:普西-琼斯(Ppusey and Jones)法

Rubber-covered rollers - Determination of apparent hardness - Part 3 : Pusey and Jones method.

ASTM D2000-12 汽车用橡胶制品的标准分类系统

1.1 This classification system covers the properties of vulcanized rubber materials (natural rubber, reclaimed rubber, synthetic rubbers, alone or in combination) that are intended for, but not limited to, use in rubber products for automotive applications. Note 18212;This classification system may serve many of the needs of other industries in much the same manner as SAE numbered steels. It must be remembered, however, that this system is subject to revision when required by automotive needs. It is recommended that the latest revision always be used. 1.2 This classification system is based on the premise that the properties of all rubber products can be arranged into characteristic material designations. These designations are determined by types, based on resistance to heat aging, and classes, based on resistance to swelling in oil. Basic levels are thus established which, together with values describing additional requirements, permit complete description of the quality of all elastomeric materials. 1.3 In all cases where the provisions of this classification system would conflict with those of the detailed specifications for a particular product, the latter shall take precedence. Note 28212;When the rubber product is to be used for purposes where the requirements are too specific to be completely prescribed by this classification system, it is necessary for the purchaser to consult the supplier in advance, to establish the appropriate properties, test methods, and specification test limits. 1.4 The values stated in SI units are to be regarded as standard.

Standard Classification System for Rubber Products in Automotive Applications

ASTM D6499-12 天然橡胶及其制品中抗原蛋白免疫测量的标准试验方法

Type 1 latex allergy most commonly manifests as localized urticaria after contact of skin with natural rubber but can also include symptoms of allergic rhinoconjunctivitis, asthma and rarely anaphylaxis. This immediate (Type I) allergy is caused by natural proteins inherent to the rubber tree, which remain on the finished natural rubber products. The quantification of protein levels in NRL products using the standard colorimetric protein assays may give spurious results due to chemical additives in the latex formulations that interfere with the assay (2,3). Furthermore, the amount of protein found in NRL products are often below the detection limits of the standard colorimetric protein assay (4,5). This test method describes an immunological method for quantitation of natural rubber latex proteins using rabbit anti-NRL serum. Rabbits immunized with NRL proteins react to the majority of the proteins present, and their sera have the capability to detect most if not all of the proteins in NRL. Therefore, although rabbit antibody reacts with antigenic material, this should not be considered as quantitative measure of total protein levels.1.1 This test method covers an immunological method to determine the amount of antigenic protein in natural rubber and its products using rabbit antisera specific for natural rubber latex (NRL) proteins. This immunoassay procedure quantitatively measures the level of antigenic latex proteins in solution using an inhibition format. The samples may include glove or other rubber product extracts which have been collected in order to measure the latex protein levels. Although this method detects antigenic proteins, it should not be considered as a measure of allergenic proteins. Correlation of protein/antigen levels with the level of allergenic proteins has not been fully established. 1.2 For the purpose of this test method, the range of protein will be measured in terms of microgram to milligram quantities. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for The Immunological Measurement of Antigenic Protein in Natural Rubber and its Products

ASTM D3853-12 橡胶及橡胶胶乳.混炼用化学药品的缩写相关的标准术语

These abbreviations are to be used in technical writing where the full chemical name of the substance is used initially, followed by the abbreviation found in this terminology. Later references to this substance may then use the abbreviation only.1.1 This terminology is a compilation of abbreviations for accelerators, vulcanizing agents, activators, antidegradants, plasticizers, softeners, processing aids, blowing agents, retarders, isocyanates, peroxides, and antireversion agents used in the compounding of rubber products. Abbreviations for rubbers are listed in Practice D1418 and a numbering system for various grades of carbon blacks is described in Classification D1765.

Standard Terminology Relating to Rubber and Rubber Laticesmdash;Abbreviations for Chemicals Used in Compounding

ASTM D6204-12 使用无转子切流变仪测量橡胶未硫化流变特性的标准试验方法

5.1 This test method is used to measure viscoelastic properties of raw rubber as well as unvulcanized rubber compounds. These viscoelastic properties may relate to factory processing behavior. 5.2 This test method may be used for quality control in rubber manufacturing processes and for research and development testing of raw rubber and rubber compounds. This test method may also be used for evaluating compound differences resulting from the use of different compounding materials. 1.1 This test method covers the use of a rotorless oscillating shear rheometer for the measurement of the flow properties of raw rubber and unvulcanized rubber compounds. These flow properties are related to factory processing. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Rubbermdash;Measurement of Unvulcanized Rheological Properties Using Rotorless Shear Rheometers

ASTM D2000-12(2017) 机动车应用橡胶产品的标准分类体系

1.1 This classification system covers the properties of vulcanized rubber materials (natural rubber, reclaimed rubber, synthetic rubbers, alone or in combination) that are intended for, but not limited to, use in rubber products for automotive applications. Note 1: This classification system may serve many of the needs of other industries in much the same manner as SAE numbered steels. It must be remembered, however, that this system is subject to revision when required by automotive needs. It is recommended that the latest revision always be used. 1.2 This classification system is based on the premise that the properties of all rubber products can be arranged into characteristic material designations. These designations are determined by types, based on resistance to heat aging, and classes, based on resistance to swelling in oil. Basic levels are thus established which, together with values describing additional requirements, permit complete description of the quality of all elastomeric materials. 1.3 In all cases where the provisions of this classification system would conflict with those of the detailed specifications for a particular product, the latter shall take precedence. Note 2: When the rubber product is to be used for purposes where the requirements are too specific to be completely prescribed by this classification system, it is necessary for the purchaser to consult the supplier in advance, to establish the appropriate properties, test methods, and specification test limits. 1.4 The values stated in SI units are to be regarded as standard. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Classification System for Rubber Products in Automotive Applications

ASTM D6601-12 使用无转子切流变仪测量橡胶固化特性和固化后特性的标准试验方法

5.1 This test method is used to determine the vulcanization characteristics of (vulcanizable) rubber compounds under selected test conditions of strain and frequency which do not significantly affect the cured dynamic properties. In the same test, this test method also will measure the dynamic properties of the vulcanizate at temperatures significantly below the cure temperature. These lower temperature measurements are necessary in order to more effectively relate to rubber product service conditions. 5.2 This test method may be used for quality control in rubber manufacturing processes and for research and development testing of rubber compounds containing curatives. This test method also may be used for evaluating cure and dynamic property differences resulting from the use of different compounding ingredients. 5.3 For additional information regarding the significance of dynamic testing of vulcanized rubber, the reader may wish to reference Guide D5992. 1.1 This test method covers the use of a rotorless oscillating shear rheometer for measuring after cure dynamic properties at predetermined temperature(s) below the cure temperature. 1.2 Specified cure conditions that approximate a ???static cure??? also are covered to minimize effects on cured rubber compound dynamic properties. This test method is not intended to replace Test Method D5289. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 Warning???Compounds based on silicone or fluoroelastomers may have high levels of thermal contraction or poor adhesion to the dies when cooled after the cure portion of this test method, causing slippage during strain sweeps. If this occurs, the results will not be reliable.

Standard Test Method for Rubber Propertiesmdash;Measurement of Cure and After-Cure Dynamic Properties Using a Rotorless Shear Rheometer

ASTM D3853-12(2017) 配方中使用化学品用橡胶和橡胶胶乳缩略语相关标准术语

3.1 These abbreviations are to be used in technical writing where the full chemical name of the substance is used initially, followed by the abbreviation found in this terminology. Later references to this substance may then use the abbreviation only. 1.1 This terminology is a compilation of abbreviations for accelerators, vulcanizing agents, activators, antidegradants, plasticizers, softeners, processing aids, blowing agents, retarders, isocyanates, peroxides, and antireversion agents used in the compounding of rubber products. Abbreviations for rubbers are listed in Practice D1418 and a numbering system for various grades of carbon blacks is described in Classification D1765. 1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Terminology Relating to Rubber and Rubber Latices&x2014;Abbreviations for Chemicals Used in Compounding

BS ISO 6101-6:2011 橡胶.用原子吸收光谱法对金属含量进行测定.镁含量的测定

Rubber. Determination of metal content by atomic absorption spectrometry. Determination of magnesium content

HG/T 3101-2011 硫化橡胶伸张时的有效弹性和滞后损失试验方法

警告—使用本标准的人员应有正规实验室工作的实践经验，本标准并未指出所有可能的安全问题，使用者有责任采用适当的安全和健康措施，并保证符合国家有关法规规定的条件。 本标准规定了测定硫化橡胶伸张时的有效弹性和滞后损失的试验方法。 本标准适用于硫化橡胶。

Vulcanized rubber.Test method of the relative hysteresis and useful elasticity by elongation

HG/T 3102-2011 硫化橡胶多次压缩试验方法

警告—使用本标准的人员应有正规实验室工作的实践经验，本标准并未指出所有可能的安全问题，使用者有责任采用适当的安全和健康措施，并保证符合国家有关法规规定的条件。 本标准规定了用往复式疲劳试验机测定硫化橡胶多次压缩后的温升、试样变形或疲劳寿命的试验方法。 本标准适用于硬度在85（邵尔A）以下的硫化橡胶。

Vulcanized rubber.Test method of multiple compression

KS M 3017-2011 丙烯腈试验方法

이 표준은 아크릴로나이트릴의 시험방법에 대하여 규정한다.

Testing methods for acrylonitrile