G40 橡胶制品综合 标准查询与下载

ASTM D926-08(2013) 橡胶属性标准试验方法:塑性与回复性行(平行板法)测试

4.1 The plasticity number and the recovery of the test specimen are related to the flow properties and the elastic properties, respectively, and may be useful in predicting processing characteristics, such as ease of forming and extrusion characteristics. 4.1.1 In this test method, plasticity is measured in an inverse manner, as noted by the final height of the specimen. Thus, high plasticity rubbers (high degree of flow during test) are indicated by a low plasticity number. 1.1 This test method covers the determination of plasticity and recovery of unvulcanized rubber by means of the parallel plate plastometer. Uncompounded, compounded, and reclaim rubber may be tested. Note 1—ISO 2007 and Test Method D3194 use a principle similar to this test method although the apparatus, test conditions, and procedure are different. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Rubber Propertymdash;Plasticity and Recovery 40;Parallel Plate Method41;

KS M ISO 3877-2:2007 轮胎、气门嘴和内胎.等义术语表.第2部分:气门嘴

이 규격은 타이어 산업에서 일반적으로 사용되는 타이어 밸브 용어에 대해서 규정한다. 용어는

Tyres, valves and tubes－List of equivalent terms－Part 2：Tyre valves

KS M ISO 3877-1:2007 轮胎、气门嘴和内胎.等义术语表.第1部分:轮胎

이 규격은 타이어 산업에서 일반적으로 사용되는 타이어 용어의 목록에 대하여 규정한다.

Tyres, valves and tubes-List of equivalent terms-Part 1:Tyres

KS M ISO 3877-4:2007 轮胎、气门嘴和内胎.等义术语表.第4部分:实心轮胎

이 규격은 타이어 산업에서 일반적으로 사용되는 통 타이어의 용어에 대하여 규정한다.

Tyres, valves and tubes-List of equivalent terms-Part 4:Solid tyres

JIS K 6422:2007 防振橡胶垫.分类标准和测试方法

この規格は，自動車用及び産業用の車両に用いるゴム製品のうち，一般に振動・衝撃の伝達防止，吸振又は衝撃の緩和を目的として使用する防振ゴムの分類基準及びその試験方法について規定する。ただし，鉄道車両用は除く。

Rubber vibration isolators -- Classification standard and testing methods

KS M ISO 247:2007 橡胶.灰分的测定

이 규격은 원료 고무, 배합 고무 및 가황 고무로부터 회분을 측정하는 두 가지 방법에 대해

Rubber－Determination of ash

KS M 6896-2007 鞋帮用人造皮革

이 규격은 신발의 겉가죽에 사용하는 인조 가죽에 대하여 규정한다.

Man-made upper material of shoes

KS M 6883-2007 鞋子用皮革

이 규격은 남자용1) 및 여자용, 어린이용2) 구두의 재료로 쓰이는 가죽에 대하여 규정한다

Leather for shoes

KS M ISO 9924-2:2007 橡胶和橡胶制品.用热裂解法测定硫化和未硫化化合物的成分.第2部分:丙烯腈丁二烯和丁基卤化橡胶

1.1 이 규격은 열분해에서 탄소를 함유한 잔류물을 형성하는 고분자를 포함하는 가황물 및

Rubber and rubber products－Determination of the composition of vulcanizates and uncured compounds by thermogravimetry－Part 2：Acrylonitrile－butadiene and halobutyl rubbers

KS M ISO 9924-1:2007 橡胶和橡胶制品.用热裂解法测定硫化和未硫化化合物的成分.第1部分:丁二烯、乙烯.丙烯共聚物和三聚物、异丁烯.异戊二烯、异戊二烯和丁二烯橡胶

이 규격은 가황물 및 미가황 혼합물에서의 카본 블랙 함량 및 회분, 전체 유기물 함량의 측

Rubber and rubber products－Determination of the composition of vulcanizates and uncured compounds by thermogravimetry－Part 1：Butadiene, ethylene－propylene copolymer and terpolymer,isobutene－isoprene, isoprene and styrene-butadiene rubbers

NAVY QPL-85322-3 NOTICE 1-2007 抗酸雨腐蚀聚氨酯橡胶涂料

QPL-85322-3, which identified products qualified under the requirements specified in MIL-C-85322, has been transformed to an equivalent qualification data set (QDS).

COATING, ELASTOMERIC, POLYURETHANE, RAIN-EROSION

ISO 6916-1:1995/Amd 1:2007 柔性多孔聚合材料.海绵和海绵多孔橡胶制品.规范.第1部分:片材.修改件1

The standard is about Flexible cellular polymeric materials — Sponge and expanded cellular rubber products — Specification Part 1: Sheeting AMENDMENT 1

Flexible cellular polymeric materials - Sponge and expanded cellular rubber products - Specification - Part 1: Sheeting; Amendment 1

DLA MS28761 REV C-2007 3,000 PSI液压扣押直口管橡胶软管装配

1. Dimensions are in inches. 2. Metric equivalents are for given for information only. 3. Unless otherwise specified, tolerances are ±.005 inch (0.13 mm). 4. The fitting identification shall be marked in accordance with MIL-DTL-8789. 5. Hex or flats shall fit standard wrench openings. 6. Threads shall be in accordance with SAE-AS8879.

FITTING END, STRAIGHT, ATTACHABLE, HYDRAULIC, HIGH PRESSURE HOSE 3,000 PSI, FLARELESS TUBE

DLA MS28760 REV E-2007 3,000 PSI液压气动扣押直口管橡胶软管装配

This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-8789.

FITTING END, STRAIGHT, ATTACHABLE, HYDRAULIC AND PNEUMATIC, HIGH PRESSURE HOSE 3,000 PSI, FLARED TUBE

DLA MS28920 REV C-2007 3,000 PSI液压45度激化管橡胶软管装配

This specification is approved for use by all Departments and Agencies of the Department of Defense.

HOSE ASSEMBLY, RUBBER, HYDRAULIC, (3,000 PSI), FITTING END TO ELBOW 45 DEG., FLARED TUBE

DLA MS28924 REV C-2007 3,000 PSI液压90度扩口管橡胶软管装配

This specification is approved for use by all Departments and Agencies of the Department of Defense.

HOSE ASSEMBLY, RUBBER, HYDRAULIC, 3,000 PSI, ELBOW 90?TO ELBOW 90? FLARED TUBE

DLA MS28921 REV C-2007 3,000 PSI液压90度激化管橡胶软管装配

This specification is approved for use by all Departments and Agencies of the Department of Defense.

HOSE ASSEMBLY, RUBBER, HYDRAULIC 3,000 PSI, STRAIGHT TO ELBOW 90 DEGREE, FLARED TUBE

DLA MS28762 REV D-2007 3,000 PSI液压扣押直口管橡胶软管装配

This specification is approved for use by all Departments and Agencies of the Department of Defense.

HOSE ASSEMBLY, RUBBER, HYDRAULIC 3000 PSI, STRAIGHT TO STRAIGHT, FLARELESS TUBE FIELD ATTACHABLE

DLA MS28759 REV D-2007 3,000 PSI液压管外扣押直口管橡胶软管装配

Dash size number refers to the nominal outside diameter of the passageway in sixteenths (1/16) of an inch. A dash 8 (-8) has an outside diameter of one-half inch (8/16).

HOSE ASSEMBLY, RUBBER, HYDRAULIC 3,000 PSI, STRAIGHT TO STRAIGHT, FLARED TUBE FIELD ATTACHABLE

SN/T 1877.4-2007 橡胶及其制品中多环芳烃的测定方法

SN/T1 877 的本部分规定了橡胶及其制品中多环芳烃的气相色谱一质谱和高效液相色谱测定方法。 本部分适用于橡胶及其制品中多环芳烃的测定。

Determination of polycyclic aromatic hydrocarbons in rubber and rubber product