共找到 1146 条与 胶管、胶带、胶布 相关的标准,共 77 页
Rubber hoses and hose assemblies - Rubber-covered spiral-wire-reinforced hydraulic types for oil-based or water-based fluids - Specification
Rubber hoses and hose assemblies - Wire-braid-reinforced hydraulic types for oil-based or water-based fluids - Specification
Rubber or plastics hoses and hose assemblies - Hydraulic-pressure impulse test without flexing (ISO 6803:2017); German version EN ISO 6803:2017
Rubber hoses and hose assemblies for saturated steam - Specification (ISO 6134:2017); German version EN ISO 6134:2017
Rubber hoses and hose assemblies for use in oil burners - Specification
Rubber and plastics hoses - Determination of adhesion between components (ISO 8033:2016); German version EN ISO 8033:2017
Rubber hoses and tubing for air and vacuum systems for internal-combustion engines. Specification
Rubber or plastics hoses and hose assemblies. Hydraulic-pressure impulse test without flexing
Rubber hoses for agricultural spraying (ISO 1401:2016); German version EN ISO 1401:2016
Rubber hoses, textile-reinforced, for compressed air - Specification (ISO 2398:2016), German version EN ISO 2398:2016
This document specifies requirements for rubber hoses and tubing for use in the various air and vacuum systems found on internal combustion engines. This document does not cover hoses used for direct power-brake actuation in trucks and trailers, nor for air intakes and ducting within the passenger compartment. The highest-temperature hoses are generally used for turbocharger applications. All hoses and tubing remain serviceable down to −40°C. NOTE Although the term vacuum is generally used, in reality the application is one of reduced air pressure used for the purposes of actuation or monitoring of the various engine-system components. The air carried by the tubing or hoses may be clean and free of contaminants but may also contain oil, fuel and their vapours as contamination, due to the particular installation and application.
Rubber hoses and tubing for air and vacuum systems for internal-combustion engines - Specification
Rubber hoses and hose assemblies for saturated steam. Specification
This document specifies requirements for two types of hoses and hose assemblies, low pressure with a maximum working pressure of 6 bar and high pressure with a maximum working pressure of 18 bar, made of rubber and hose fittings made of metal, designed to convey saturated steam and hot water condensate. Each type is divided into two classes having either an oil resistant or non-oil resistant cover. NOTE Information on the frequency of testing of hose assemblies in use and storage is given in Annex A and Annex B.
Rubber hoses and hose assemblies for saturated steam - Specification
Rubber and plastics hoses and hose assemblies. Guidelines for selection, storage, use and maintenance
Rubber hoses and hose assemblies for water suction and discharge. Specification
Rubber hoses, textile-reinforced, for compressed air. Specification
Rubber hoses for agricultural spraying
This part of ISO 13775 specifies test requirements and test methods for extruded thermoplastic tubing and hoses for use in petroleum-based-fuel lines in vehicles powered by internal-combustion engines.
Thermoplastic tubing and hoses for automotive use - Part 2: Petroleum-based-fuel applications
This document specifies the minimum requirements for textile-reinforced, smooth-bore rubber watersuction and discharge hoses and hose assemblies. Three types of hoses and hose assemblies are specified according to their operating duty requirements, i.e. their ambient and water temperature ranges: — ambient temperatures: −25 °C to +70 °C; — water temperatures during operation: 0 °C to +70 °C.
Rubber hoses and hose assemblies for water suction and discharge - Specification
Rubber hose assemblies for oil suction and discharge services - Specification for the assemblies; German version EN 1765:2016
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号